The regulator-fec*-pwdn regulators were used to deassert the PWDN signal of ethernet PHY, e.g. not powering. This is not necessary as the line has a pull-up already. Instead of the combo pad of the PHY for IRQ support. Signed-off-by: Alexander Stein <alexander.stein@xxxxxxxxxxxxxxx> --- arch/arm/boot/dts/nxp/imx/imx7-mba7.dtsi | 23 ++--------------------- arch/arm/boot/dts/nxp/imx/imx7d-mba7.dts | 3 ++- 2 files changed, 4 insertions(+), 22 deletions(-) diff --git a/arch/arm/boot/dts/nxp/imx/imx7-mba7.dtsi b/arch/arm/boot/dts/nxp/imx/imx7-mba7.dtsi index 304281681abfe..576a7df505d3b 100644 --- a/arch/arm/boot/dts/nxp/imx/imx7-mba7.dtsi +++ b/arch/arm/boot/dts/nxp/imx/imx7-mba7.dtsi @@ -87,26 +87,6 @@ iio-hwmon { <&adc2 0>, <&adc2 1>, <&adc2 2>, <&adc2 3>; }; - reg_fec1_pwdn: regulator-fec1-pwdn { - compatible = "regulator-fixed"; - regulator-name = "PWDN_FEC1"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; - - reg_fec2_pwdn: regulator-fec2-pwdn { - compatible = "regulator-fixed"; - regulator-name = "PWDN_FEC2"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - gpio = <&gpio2 31 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; - reg_usb_otg1_vbus: regulator-usb-otg1-vbus { compatible = "regulator-fixed"; regulator-name = "VBUS_USBOTG1"; @@ -231,7 +211,6 @@ &fec1 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_enet1>; phy-mode = "rgmii-id"; - phy-supply = <®_fec1_pwdn>; phy-handle = <ðphy1_0>; fsl,magic-packet; status = "okay"; @@ -252,6 +231,8 @@ ethphy1_0: ethernet-phy@0 { reset-gpios = <&gpio7 15 GPIO_ACTIVE_LOW>; reset-assert-us = <1000>; reset-deassert-us = <500>; + interrupt-parent = <&gpio1>; + interrupts = <9 IRQ_TYPE_EDGE_FALLING>; }; }; }; diff --git a/arch/arm/boot/dts/nxp/imx/imx7d-mba7.dts b/arch/arm/boot/dts/nxp/imx/imx7d-mba7.dts index 0443faa3dfae4..e3ee16f1aaa96 100644 --- a/arch/arm/boot/dts/nxp/imx/imx7d-mba7.dts +++ b/arch/arm/boot/dts/nxp/imx/imx7d-mba7.dts @@ -21,7 +21,6 @@ &fec2 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_enet2>; phy-mode = "rgmii-id"; - phy-supply = <®_fec2_pwdn>; phy-handle = <ðphy2_0>; fsl,magic-packet; status = "okay"; @@ -42,6 +41,8 @@ ethphy2_0: ethernet-phy@0 { reset-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>; reset-assert-us = <1000>; reset-deassert-us = <500>; + interrupt-parent = <&gpio2>; + interrupts = <31 IRQ_TYPE_EDGE_FALLING>; }; }; }; -- 2.34.1