Add the dt-bindings for the NXP SIUL2 module which is a multi function device. It can export information about the SoC, configure the pinmux&pinconf for pins and it is also a GPIO controller with interrupt capability. Signed-off-by: Andrei Stefanescu <andrei.stefanescu@xxxxxxxxxxx> --- .../devicetree/bindings/mfd/nxp,siul2.yaml | 191 ++++++++++++++++++ 1 file changed, 191 insertions(+) create mode 100644 Documentation/devicetree/bindings/mfd/nxp,siul2.yaml diff --git a/Documentation/devicetree/bindings/mfd/nxp,siul2.yaml b/Documentation/devicetree/bindings/mfd/nxp,siul2.yaml new file mode 100644 index 000000000000..141ec1219821 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/nxp,siul2.yaml @@ -0,0 +1,191 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright 2024 NXP +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mfd/nxp,siul2.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: System Integration Unit Lite2 (SIUL2) + +maintainers: + - Andrei Stefanescu <andrei.stefanescu@xxxxxxxxxxx> + +description: | + SIUL2 is a hardware block which implements pinmuxing, + pinconf, GPIOs (some with interrupt capability) and + registers which contain information about the SoC. + There are generally two SIUL2 modules whose functionality + is grouped together. For example interrupt configuration + registers are part of SIUL2_1 even though interrupts are + also available for SIUL2_0 pins. + + The following register types are exported by SIUL2: + - MIDR (MCU ID Register) - information related to the SoC + - interrupt configuration registers + - MSCR (Multiplexed Signal Configuration Register) - pinmuxing and pinconf + - IMCR (Input Multiplexed Signal Configuration Register)- pinmuxing + - PGPDO (Parallel GPIO Pad Data Out Register) - GPIO output value + - PGPDI (Parallel GPIO Pad Data In Register) - GPIO input value + + Most registers are 32bit wide with the exception of PGPDO/PGPDI which are + 16bit wide. + +properties: + compatible: + enum: + - nxp,s32g2-siul2 + - nxp,s32g3-siul2 + + reg: + items: + - description: SIUL2_0 module memory + - description: SIUL2_1 module memory + + reg-names: + items: + - const: siul20 + - const: siul21 + + gpio-controller: true + + '#gpio-cells': + const: 2 + + gpio-ranges: + minItems: 2 + maxItems: 2 + + gpio-reserved-ranges: + minItems: 2 + + interrupts: + maxItems: 1 + + interrupt-controller: true + + '#interrupt-cells': + const: 2 + + nvmem-layout: + $ref: /schemas/nvmem/layouts/nvmem-layout.yaml# + description: + This container may reference an NVMEM layout parser. + +patternProperties: + '-hog(-[0-9]+)?$': + required: + - gpio-hog + + '-pins$': + type: object + additionalProperties: false + + patternProperties: + '-grp[0-9]$': + type: object + allOf: + - $ref: /schemas/pinctrl/pinmux-node.yaml# + - $ref: /schemas/pinctrl/pincfg-node.yaml# + description: + Pinctrl node's client devices specify pin muxes using subnodes, + which in turn use the standard properties below. + + properties: + bias-disable: true + bias-high-impedance: true + bias-pull-up: true + bias-pull-down: true + drive-open-drain: true + input-enable: true + output-enable: true + + pinmux: + description: | + An integer array for representing pinmux configurations of + a device. Each integer consists of a PIN_ID and a 4-bit + selected signal source(SSS) as IOMUX setting, which is + calculated as: pinmux = (PIN_ID << 4 | SSS) + + slew-rate: + description: Supported slew rate based on Fmax values (MHz) + enum: [83, 133, 150, 166, 208] + + additionalProperties: false + +required: + - compatible + - reg + - reg-names + - gpio-controller + - "#gpio-cells" + - gpio-ranges + - gpio-reserved-ranges + - interrupts + - interrupt-controller + - "#interrupt-cells" + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + + siul2: siul2@4009c000 { + compatible = "nxp,s32g2-siul2"; + reg = <0x4009c000 0x179c>, + <0x44010000 0x17b0>; + reg-names = "siul20", "siul21"; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&siul2 0 0 102>, <&siul2 112 112 79>; + gpio-reserved-ranges = <102 10>, <123 21>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>; + + jtag_pins: jtag-pins { + jtag-grp0 { + pinmux = <0x0>; + input-enable; + bias-pull-up; + slew-rate = <166>; + }; + + jtag-grp1 { + pinmux = <0x11>; + slew-rate = <166>; + }; + + jtag-grp2 { + pinmux = <0x40>; + input-enable; + bias-pull-down; + slew-rate = <166>; + }; + + jtag-grp3 { + pinmux = <0x23c0>, + <0x23d0>, + <0x2320>; + }; + + jtag-grp4 { + pinmux = <0x51>; + input-enable; + bias-pull-up; + slew-rate = <166>; + }; + }; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + soc-major@0 { + reg = <0 0x4>; + }; + }; + }; +... -- 2.45.2
