On 26.10.2024 6:56 PM, Krishna Kurapati wrote:
>
>
> On 10/25/2024 11:58 PM, Konrad Dybcio wrote:
>> On 11.10.2024 9:46 AM, Krishna Kurapati wrote:
>>
>> The commit title should include a `qcs8300: ` part, like others in
>> the directory (see git log --oneline arch/arm64/boot/dts/qcom).
>>
>>> Add support for USB controllers on QCS8300. The second
>>> controller is only High Speed capable.
>>>
>>> Signed-off-by: Krishna Kurapati <quic_kriskura@xxxxxxxxxxx>
>>> ---
>>> arch/arm64/boot/dts/qcom/qcs8300.dtsi | 168 ++++++++++++++++++++++++++
>>> 1 file changed, 168 insertions(+)
>>>
>>> diff --git a/arch/arm64/boot/dts/qcom/qcs8300.dtsi b/arch/arm64/boot/dts/qcom/qcs8300.dtsi
>>> index 2c35f96c3f28..4e6ba9f49b95 100644
>>> --- a/arch/arm64/boot/dts/qcom/qcs8300.dtsi
>>> +++ b/arch/arm64/boot/dts/qcom/qcs8300.dtsi
>>> @@ -1363,6 +1363,174 @@ IPCC_MPROC_SIGNAL_GLINK_QMP
>>> qcom,remote-pid = <5>;
>>> };
>>> };
>>> +
>>> + usb_1_hsphy: phy@8904000 {
>>> + compatible = "qcom,qcs8300-usb-hs-phy",
>>> + "qcom,usb-snps-hs-7nm-phy";
>>> + reg = <0x0 0x8904000 0x0 0x400>;
>>
>> Please pad the address parts to 8 hex digits with leading zeroes.
>>
>>> +
>>> + clocks = <&rpmhcc RPMH_CXO_CLK>;
>>> + clock-names = "ref";
>>> +
>>> + resets = <&gcc GCC_USB2_PHY_PRIM_BCR>;
>>> +
>>> + #phy-cells = <0>;
>>> +
>>> + status = "disabled";
>>> + };
>>> +
>>> + usb_2_hsphy: phy@8906000 {
>>> + compatible = "qcom,qcs8300-usb-hs-phy",
>>> + "qcom,usb-snps-hs-7nm-phy";
>>> + reg = <0x0 0x08906000 0x0 0x400>;
>>> +
>>> + clocks = <&rpmhcc RPMH_CXO_CLK>;
>>> + clock-names = "ref";
>>> +
>>> + resets = <&gcc GCC_USB2_PHY_SEC_BCR>;
>>> +
>>> + #phy-cells = <0>;
>>> +
>>> + status = "disabled";
>>> + };
>>> +
>>> + usb_qmpphy: phy@8907000 {
>>> + compatible = "qcom,qcs8300-qmp-usb3-uni-phy";
>>> + reg = <0x0 0x8907000 0x0 0x2000>;
>>> +
>>> + clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
>>> + <&gcc GCC_USB_CLKREF_EN>,
>>> + <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>,
>>> + <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
>>> + clock-names = "aux", "ref", "com_aux", "pipe";
>>
>> Please make this a vertical list like in the node below.
>>
>> [...]
>>
>>> + interconnects = <&aggre1_noc MASTER_USB3_0 0 &mc_virt SLAVE_EBI1 0>,
>>
>> QCOM_ICC_TAG_ALWAYS, see x1e80100.dtsi
>>
>>> + <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_USB3_0 0>;
>>> + interconnect-names = "usb-ddr", "apps-usb";
>>> +
>>> + wakeup-source;
>>> +
>>> + status = "disabled";
>>> +
>>> + usb_1_dwc3: usb@a600000 {
>>> + compatible = "snps,dwc3";
>>> + reg = <0x0 0x0a600000 0x0 0xe000>;
>>> + interrupts = <GIC_SPI 292 IRQ_TYPE_LEVEL_HIGH>;
>>> + iommus = <&apps_smmu 0x80 0x0>;
>>> + phys = <&usb_1_hsphy>, <&usb_qmpphy>;
>>> + phy-names = "usb2-phy", "usb3-phy";
>>> + snps,dis_u2_susphy_quirk;
>>> + snps,dis_enblslpm_quirk;
>>
>> That's a very low number of quirks.. Should we have some more?
>>
>
> snps,dis-u1-entry-quirk;
> snps,dis-u2-entry-quirk;
> snps,dis_u2_susphy_quirk;
> snps,ssp-u3-u0-quirk;
>
> I would actually like to add these as well, but there is no precedent in upstream as to what quirks to add for usb nodes
Every single one that applies to the hardware ;)
> , so I kept only a couple of them. Ideally downstream we disable u1u2 for almost all targets because of some issues in the past. (atleast during tethering use cases, but I need to double check though).
Does
5b8baed4b881 ("arm64: dts: qcom: sc7180: Disable SuperSpeed instances in park mode")
apply here too?
Konrad
