On Fri, Oct 25, 2024 at 08:48:48AM +0300, Dmitry Baryshkov wrote:
> On Fri, 25 Oct 2024 at 06:00, Yuanjie Yang <quic_yuanjiey@xxxxxxxxxxx> wrote:
> >
> > On Thu, Oct 24, 2024 at 11:42:26PM +0300, Dmitry Baryshkov wrote:
> > > On Wed, Oct 23, 2024 at 05:27:07PM +0800, Yuanjie Yang wrote:
> > > > Add SD and emmc support to the QCS615 Ride platform. The SD controller
> > > > and emmc controller of QCS615 are derived from SM6115. Include the
> > > > relevant binding documents accordingly. Additionally, configure
> > > > emmc-related and SD-related opp, power, and interconnect settings
> > > > in the device tree.
> > > >
> > > > Signed-off-by: Yuanjie Yang <quic_yuanjiey@xxxxxxxxxxx>
> > > > ---
> > > > arch/arm64/boot/dts/qcom/qcs615.dtsi | 198 +++++++++++++++++++++++++++
> > > > 1 file changed, 198 insertions(+)
> > > >
> > > > diff --git a/arch/arm64/boot/dts/qcom/qcs615.dtsi b/arch/arm64/boot/dts/qcom/qcs615.dtsi
> > > > index fcba83fca7cf..3840edf13fe8 100644
> > > > --- a/arch/arm64/boot/dts/qcom/qcs615.dtsi
> > > > +++ b/arch/arm64/boot/dts/qcom/qcs615.dtsi
> > > > @@ -399,6 +399,65 @@ qfprom: efuse@780000 {
> > > > #size-cells = <1>;
> > > > };
> > > >
> > > > + sdhc_1: mmc@7c4000 {
> > > > + compatible = "qcom,qcs615-sdhci", "qcom,sdhci-msm-v5";
> > > > + reg = <0 0x7c4000 0 0x1000>,
> > > > + <0 0x7c5000 0 0x1000>;
> > >
> > > <0x0 0x007c4000 0x0 0x1000> (this applies to all address nodes, so
> > > sdhc_2 too.
> > Thanks, in the next version, I will adjust all the values in the reg to hexadecimal.
>
> Not only that. In the entry that I've posted there is a second change.
Thanks, of course, in the next version I will change all the values in the reg of
sdhc1 and sdhc2 to hexadecimal.I will also check other places to see if there are
similar situations that need to be modified.
> >
> > >
> > > > + reg-names = "hc",
> > > > + "cqhci";
> > > > +
> > > > + interrupts = <GIC_SPI 641 IRQ_TYPE_LEVEL_HIGH>,
> > > > + <GIC_SPI 644 IRQ_TYPE_LEVEL_HIGH>;
> > > > + interrupt-names = "hc_irq",
> > > > + "pwr_irq";
> > > > +
> > > > + clocks = <&gcc GCC_SDCC1_AHB_CLK>,
> > > > + <&gcc GCC_SDCC1_APPS_CLK>,
> > > > + <&rpmhcc RPMH_CXO_CLK>,
> > > > + <&gcc GCC_SDCC1_ICE_CORE_CLK>;
> > > > + clock-names = "iface",
> > > > + "core",
> > > > + "xo",
> > > > + "ice";
> > > > +
> > > > + resets = <&gcc GCC_SDCC1_BCR>;
> > > > +
> > > > + power-domains = <&rpmhpd RPMHPD_CX>;
> > > > + operating-points-v2 = <&sdhc1_opp_table>;
> > > > + iommus = <&apps_smmu 0x02c0 0x0>;
> > > > + interconnects = <&aggre1_noc MASTER_SDCC_1 QCOM_ICC_TAG_ALWAYS
> > > > + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>,
> > > > + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
> > > > + &config_noc SLAVE_SDCC_1 QCOM_ICC_TAG_ALWAYS>;
> > > > + interconnect-names = "sdhc-ddr",
> > > > + "cpu-sdhc";
> > > > +
> > > > + bus-width = <8>;
> > > > + qcom,dll-config = <0x000f642c>;
> > > > + qcom,ddr-config = <0x80040868>;
> > > > + supports-cqe;
> > > > + dma-coherent;
> > > > + mmc-ddr-1_8v;
> > > > + mmc-hs200-1_8v;
> > > > + mmc-hs400-1_8v;
> > > > + mmc-hs400-enhanced-strobe;
> > >
> > > Are these board properties or SoC properties?
> > Thanks, these properties are Soc properties, so I put them in dtsi.
> >
> > > > + status = "disabled";
> > > > +
> > >
> > > --
> > > With best wishes
> > > Dmitry
> >
> > Thanks,
> > Yuanjie
>
>
>
> --
> With best wishes
> Dmitry
Thanks,
Yuanjie
