Adds bootph-* properties to the leaf nodes to enable bootloaders to
utilise them.
Following adds bootph-* to
- System controller nodes that allow controlling power domain, clocks, etc.
- secure_proxy_sa3/secure_proxy_main mboxes for communication with
System Controller
- mcu_ringacc/mcu_udmap for DMA to SMS
- chipid for detection soc information.
- mcu_timer0 for bootloader tick-timer.
- wkup_vtm for enabling Adaptive voltage scaling(AVS) support
Reviewed-by: Andrew Davis <afd@xxxxxx>
Signed-off-by: Manorit Chawdhry <m-chawdhry@xxxxxx>
---
Notes:
R-by picked up in v3 ( Andrew )
arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi | 1 +
arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi | 13 +++++++++++++
2 files changed, 14 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
index 9ed6949b40e9..9889144d665a 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
@@ -816,6 +816,7 @@ secure_proxy_main: mailbox@32c00000 {
<0x00 0x32800000 0x00 0x100000>;
interrupt-names = "rx_011";
interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ bootph-all;
};
hwspinlock: spinlock@30e00000 {
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
index 9d96b19d0e7c..c36888c45531 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
@@ -21,16 +21,19 @@ sms: system-controller@44083000 {
k3_pds: power-controller {
compatible = "ti,sci-pm-domain";
#power-domain-cells = <2>;
+ bootph-all;
};
k3_clks: clock-controller {
compatible = "ti,k2g-sci-clk";
#clock-cells = <2>;
+ bootph-all;
};
k3_reset: reset-controller {
compatible = "ti,sci-reset";
#reset-cells = <2>;
+ bootph-all;
};
};
@@ -43,6 +46,7 @@ wkup_conf: bus@43000000 {
chipid: chipid@14 {
compatible = "ti,am654-chipid";
reg = <0x14 0x4>;
+ bootph-all;
};
};
@@ -53,6 +57,8 @@ secure_proxy_sa3: mailbox@43600000 {
reg = <0x00 0x43600000 0x00 0x10000>,
<0x00 0x44880000 0x00 0x20000>,
<0x00 0x44860000 0x00 0x20000>;
+ bootph-pre-ram;
+
/*
* Marked Disabled:
* Node is incomplete as it is meant for bootloaders and
@@ -167,6 +173,7 @@ mcu_timer0: timer@40400000 {
assigned-clocks = <&k3_clks 35 1>;
assigned-clock-parents = <&k3_clks 35 2>;
power-domains = <&k3_pds 35 TI_SCI_PD_EXCLUSIVE>;
+ bootph-pre-ram;
ti,timer-pwm;
/* Non-MPU Firmware usage */
status = "reserved";
@@ -361,6 +368,7 @@ wkup_i2c0: i2c@42120000 {
clocks = <&k3_clks 223 1>;
clock-names = "fck";
power-domains = <&k3_pds 223 TI_SCI_PD_EXCLUSIVE>;
+ bootph-all;
status = "disabled";
};
@@ -469,6 +477,7 @@ mcu_ringacc: ringacc@2b800000 {
<0x0 0x2a500000 0x0 0x40000>,
<0x0 0x28440000 0x0 0x40000>;
reg-names = "rt", "fifos", "proxy_gcfg", "proxy_target", "cfg";
+ bootph-all;
ti,num-rings = <286>;
ti,sci-rm-range-gp-rings = <0x1>;
ti,sci = <&sms>;
@@ -488,6 +497,7 @@ mcu_udmap: dma-controller@285c0000 {
"tchan", "rchan", "rflow";
msi-parent = <&main_udmass_inta>;
#dma-cells = <1>;
+ bootph-all;
ti,sci = <&sms>;
ti,sci-dev-id = <273>;
@@ -507,6 +517,8 @@ secure_proxy_mcu: mailbox@2a480000 {
reg = <0x00 0x2a480000 0x00 0x80000>,
<0x00 0x2a380000 0x00 0x80000>,
<0x00 0x2a400000 0x00 0x80000>;
+ bootph-pre-ram;
+
/*
* Marked Disabled:
* Node is incomplete as it is meant for bootloaders and
@@ -667,6 +679,7 @@ wkup_vtm0: temperature-sensor@42040000 {
<0x00 0x42050000 0x0 0x350>;
power-domains = <&k3_pds 180 TI_SCI_PD_SHARED>;
#thermal-sensor-cells = <1>;
+ bootph-pre-ram;
};
mcu_r5fss0: r5fss@41000000 {
--
2.46.0
