Re: [PATCH v2 04/11] DT: Add documentation for the mfd Maxim max77693

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




Hi Sakari,

On 03/28/2015 11:55 PM, Sakari Ailus wrote:
On Fri, Mar 27, 2015 at 02:49:38PM +0100, Jacek Anaszewski wrote:
This patch adds device tree binding documentation for
the flash cell of the Maxim max77693 multifunctional device.

Signed-off-by: Jacek Anaszewski <j.anaszewski@xxxxxxxxxxx>
Signed-off-by: Andrzej Hajda <a.hajda@xxxxxxxxxxx>
Acked-by: Kyungmin Park <kyungmin.park@xxxxxxxxxxx>
Acked-by: Sakari Ailus <sakari.ailus@xxxxxxxxxxxxxxx>
Cc: Lee Jones <lee.jones@xxxxxxxxxx>
Cc: Chanwoo Choi <cw00.choi@xxxxxxxxxxx>
Cc: Bryan Wu <cooloney@xxxxxxxxx>
Cc: Richard Purdie <rpurdie@xxxxxxxxx>
---
  Documentation/devicetree/bindings/mfd/max77693.txt |   61 ++++++++++++++++++++
  1 file changed, 61 insertions(+)

diff --git a/Documentation/devicetree/bindings/mfd/max77693.txt b/Documentation/devicetree/bindings/mfd/max77693.txt
index 38e6440..15c546ea 100644
--- a/Documentation/devicetree/bindings/mfd/max77693.txt
+++ b/Documentation/devicetree/bindings/mfd/max77693.txt
@@ -76,7 +76,53 @@ Optional properties:
      Valid values: 4300000, 4700000, 4800000, 4900000
      Default: 4300000

+- led : the LED submodule device node
+
+There are two LED outputs available - FLED1 and FLED2. Each of them can
+control a separate LED or they can be connected together to double
+the maximum current for a single connected LED. One LED is represented
+by one child node.
+
+Required properties:
+- compatible : Must be "maxim,max77693-led".
+
+Optional properties:
+- maxim,trigger-type : Flash trigger type.
+	Possible trigger types:
+		LEDS_TRIG_TYPE_EDGE (0) - Rising edge of the signal triggers
+			the flash,
+		LEDS_TRIG_TYPE_LEVEL (1) - Strobe pulse length controls duration
+			of the flash.
+- maxim,boost-mode :
+	In boost mode the device can produce up to 1.2A of total current
+	on both outputs. The maximum current on each output is reduced
+	to 625mA then. If not enabled explicitly, boost setting defaults to
+	LEDS_BOOST_FIXED in case both current sources are used.
+	Possible values:
+		LEDS_BOOST_OFF (0) - no boost,
+		LEDS_BOOST_ADAPTIVE (1) - adaptive mode,
+		LEDS_BOOST_FIXED (2) - fixed mode.
+- maxim,boost-mvout : Output voltage of the boost module in millivolts.

What are the possible values for this?

maxim,boost-mvout : Output voltage of the boost module in millivolts
	Range: 3300 - 5500

Do you think it is necessary to mention also allowed step for all the
values?

Is the datasheet publicly available btw.?

I have an access only to the non-public one.

+- maxim,mvsys-min : Low input voltage level in millivolts. Flash is not fired
+	if chip estimates that system voltage could drop below this level due
+	to flash power consumption.
+
+Required properties of the LED child node:
+- led-sources : see Documentation/devicetree/bindings/leds/common.txt;
+		device current output identifiers: 0 - FLED1, 1 - FLED2
+
+Optional properties of the LED child node:
+- label : see Documentation/devicetree/bindings/leds/common.txt
+- max-microamp : see Documentation/devicetree/bindings/leds/common.txt
+		Range: 15625 - 250000
+- flash-max-microamp : see Documentation/devicetree/bindings/leds/common.txt
+		Range: 15625 - 1000000
+- flash-timeout-us : see Documentation/devicetree/bindings/leds/common.txt
+		Range: 62500 - 1000000
+
  Example:
+#include <dt-bindings/leds/common.h>
+
  	max77693@66 {
  		compatible = "maxim,max77693";
  		reg = <0x66>;
@@ -117,5 +163,20 @@ Example:
  			maxim,thermal-regulation-celsius = <75>;
  			maxim,battery-overcurrent-microamp = <3000000>;
  			maxim,charge-input-threshold-microvolt = <4300000>;
+
+		led {
+			compatible = "maxim,max77693-led";
+			maxim,trigger-type = <LEDS_TRIG_TYPE_LEVEL>;
+			maxim,boost-mode = <LEDS_BOOST_FIXED>;
+			maxim,boost-mvout = <5000>;
+			maxim,mvsys-min = <2400>;
+
+			camera_flash: flash-led {
+				label = "max77693-flash";
+				led-sources = <0>, <1>;
+				max-microamp = <500000>;
+				flash-max-microamp = <1250000>;
+				flash-timeout-us = <1000000>;
+			};
  		};
  	};



--
Best Regards,
Jacek Anaszewski
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux