On Thu, Oct 03, 2024 at 02:15:37PM -0400, Frank Li wrote: > From: Richard Zhu <hongxing.zhu@xxxxxxx> > > Add PCIe support for i.MX8QXP, i.MX8QM and i.MX8DXL. > > Signed-off-by: Richard Zhu <hongxing.zhu@xxxxxxx> > Signed-off-by: Frank Li <Frank.Li@xxxxxxx> > --- > Change from v1 to v2 > - none > > On going discussion: > https://lore.kernel.org/imx/20240930-pci_fixup_addr-v3-2-80ee70352fc7@xxxxxxx/ > don't affect this dts. > This work for with/without above patches. > --- > .../boot/dts/freescale/imx8-ss-hsio.dtsi | 123 +++++++++++ > .../boot/dts/freescale/imx8dxl-ss-hsio.dtsi | 52 +++++ > arch/arm64/boot/dts/freescale/imx8dxl.dtsi | 2 + > .../boot/dts/freescale/imx8qm-ss-hsio.dtsi | 209 ++++++++++++++++++ > arch/arm64/boot/dts/freescale/imx8qm.dtsi | 2 + > .../boot/dts/freescale/imx8qxp-ss-hsio.dtsi | 41 ++++ > arch/arm64/boot/dts/freescale/imx8qxp.dtsi | 2 + > 7 files changed, 431 insertions(+) > create mode 100644 arch/arm64/boot/dts/freescale/imx8-ss-hsio.dtsi > create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-ss-hsio.dtsi > create mode 100644 arch/arm64/boot/dts/freescale/imx8qm-ss-hsio.dtsi > create mode 100644 arch/arm64/boot/dts/freescale/imx8qxp-ss-hsio.dtsi > > diff --git a/arch/arm64/boot/dts/freescale/imx8-ss-hsio.dtsi b/arch/arm64/boot/dts/freescale/imx8-ss-hsio.dtsi > new file mode 100644 > index 0000000000000..bf05cae05d27a > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/imx8-ss-hsio.dtsi > @@ -0,0 +1,123 @@ > +// SPDX-License-Identifier: GPL-2.0+ > +/* > + * Copyright 2024 NXP > + * > + * Richard Zhu <hongxing.zhu@xxxxxxx> > + */ > +#include <dt-bindings/phy/phy.h> > + > +hsio_axi_clk: clock-hsio-axi { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + clock-frequency = <400000000>; > + clock-output-names = "hsio_axi_clk"; > +}; > + > +hsio_per_clk: clock-hsio-per { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + clock-frequency = <133333333>; > + clock-output-names = "hsio_per_clk"; > +}; > + > +hsio_refa_clk: clock-hsio-refa { > + compatible = "gpio-gate-clock"; > + clocks = <&xtal100m>; > + #clock-cells = <0>; > + enable-gpios = <&lsio_gpio4 27 GPIO_ACTIVE_LOW>; > +}; > + > +hsio_refb_clk: clock-hsio-refb { > + compatible = "gpio-gate-clock"; > + clocks = <&xtal100m>; > + #clock-cells = <0>; > + enable-gpios = <&lsio_gpio4 1 GPIO_ACTIVE_LOW>; > +}; > + > +xtal100m: clock-xtal100m { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + clock-frequency = <100000000>; > + clock-output-names = "xtal_100MHz"; > +}; > + > +hsio_subsys: bus@5f000000 { > + compatible = "simple-bus"; > + ranges = <0x5f000000 0x0 0x5f000000 0x21000000>, > + <0x80000000 0x0 0x70000000 0x10000000>; > + #address-cells = <1>; > + #size-cells = <1>; > + dma-ranges = <0x80000000 0 0x80000000 0x80000000>; > + > + pcieb: pcie@5f010000 { > + compatible = "fsl,imx8q-pcie"; > + reg = <0x5f010000 0x10000>, > + <0x8ff00000 0x80000>; > + reg-names = "dbi", "config"; > + ranges = <0x81000000 0 0x00000000 0x8ff80000 0 0x00010000>, > + <0x82000000 0 0x80000000 0x80000000 0 0x0ff00000>; > + #interrupt-cells = <1>; > + interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names = "msi"; > + #address-cells = <3>; > + #size-cells = <2>; > + clocks = <&pcieb_lpcg IMX_LPCG_CLK_6>, > + <&pcieb_lpcg IMX_LPCG_CLK_4>, > + <&pcieb_lpcg IMX_LPCG_CLK_5>; > + clock-names = "dbi", "mstr", "slv"; > + bus-range = <0x00 0xff>; > + device_type = "pci"; > + fsl,max-link-speed = <3>; Can we put vendor property after generic ones? > + interrupt-map = <0 0 0 1 &gic 0 105 4>, > + <0 0 0 2 &gic 0 106 4>, > + <0 0 0 3 &gic 0 107 4>, > + <0 0 0 4 &gic 0 108 4>; > + interrupt-map-mask = <0 0 0 0x7>; > + num-lanes = <1>; > + num-viewport = <4>; > + power-domains = <&pd IMX_SC_R_PCIE_B>; > + status = "disabled"; > + }; > + > + pcieb_lpcg: clock-controller@5f060000 { > + compatible = "fsl,imx8qxp-lpcg"; > + reg = <0x5f060000 0x10000>; > + clocks = <&hsio_axi_clk>, <&hsio_axi_clk>, <&hsio_axi_clk>; > + #clock-cells = <1>; > + clock-indices = <IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_5>, <IMX_LPCG_CLK_6>; > + clock-output-names = "hsio_pcieb_mstr_axi_clk", > + "hsio_pcieb_slv_axi_clk", > + "hsio_pcieb_dbi_axi_clk"; > + power-domains = <&pd IMX_SC_R_PCIE_B>; > + }; > + > + phyx1_crr1_lpcg: clock-controller@5f0b0000 { > + compatible = "fsl,imx8qxp-lpcg"; > + reg = <0x5f0b0000 0x10000>; > + clocks = <&hsio_per_clk>; > + #clock-cells = <1>; > + clock-indices = <IMX_LPCG_CLK_4>; > + clock-output-names = "hsio_phyx1_per_clk"; > + power-domains = <&pd IMX_SC_R_SERDES_1>; > + }; > + > + pcieb_crr3_lpcg: clock-controller@5f0d0000 { > + compatible = "fsl,imx8qxp-lpcg"; > + reg = <0x5f0d0000 0x10000>; > + clocks = <&hsio_per_clk>; > + #clock-cells = <1>; > + clock-indices = <IMX_LPCG_CLK_4>; > + clock-output-names = "hsio_pcieb_per_clk"; > + power-domains = <&pd IMX_SC_R_PCIE_B>; > + }; > + > + misc_crr5_lpcg: clock-controller@5f0f0000 { > + compatible = "fsl,imx8qxp-lpcg"; > + reg = <0x5f0f0000 0x10000>; > + clocks = <&hsio_per_clk>; > + #clock-cells = <1>; > + clock-indices = <IMX_LPCG_CLK_4>; > + clock-output-names = "hsio_misc_per_clk"; > + power-domains = <&pd IMX_SC_R_HSIO_GPIO>; > + }; > +}; > diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-ss-hsio.dtsi b/arch/arm64/boot/dts/freescale/imx8dxl-ss-hsio.dtsi > new file mode 100644 > index 0000000000000..f3104e205ae89 > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/imx8dxl-ss-hsio.dtsi > @@ -0,0 +1,52 @@ > +// SPDX-License-Identifier: GPL-2.0+ > +/* > + * Copyright 2024 NXP > + */ > + > +&hsio_subsys { > + phyx1_lpcg: clock-controller@5f090000 { > + compatible = "fsl,imx8qxp-lpcg"; > + reg = <0x5f090000 0x10000>; > + clocks = <&hsio_refb_clk>, <&hsio_per_clk>, > + <&hsio_per_clk>, <&hsio_per_clk>; > + #clock-cells = <1>; > + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_1>, > + <IMX_LPCG_CLK_2>, <IMX_LPCG_CLK_4>; > + clock-output-names = "hsio_phyx1_pclk", > + "hsio_phyx1_epcs_tx_clk", > + "hsio_phyx1_epcs_rx_clk", > + "hsio_phyx1_apb_clk"; > + power-domains = <&pd IMX_SC_R_SERDES_1>; > + }; > + > + hsio_phy: phy@5f1a0000 { > + compatible = "fsl,imx8qxp-hsio"; > + reg = <0x5f1a0000 0x10000>, > + <0x5f120000 0x10000>, > + <0x5f140000 0x10000>, > + <0x5f160000 0x10000>; > + reg-names = "reg", "phy", "ctrl", "misc"; > + clocks = <&phyx1_lpcg IMX_LPCG_CLK_0>, > + <&phyx1_lpcg IMX_LPCG_CLK_4>, > + <&phyx1_crr1_lpcg IMX_LPCG_CLK_4>, > + <&pcieb_crr3_lpcg IMX_LPCG_CLK_4>, > + <&misc_crr5_lpcg IMX_LPCG_CLK_4>; > + clock-names = "pclk0", "apb_pclk0", "phy0_crr", "ctl0_crr", > + "misc_crr"; > + #phy-cells = <3>; > + power-domains = <&pd IMX_SC_R_SERDES_1>; > + status = "disabled"; > + }; > +}; > + > +&pcieb { > + #interrupt-cells = <1>; > + interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names = "msi"; > + interrupt-map = <0 0 0 1 &gic 0 47 4>, > + <0 0 0 2 &gic 0 48 4>, > + <0 0 0 3 &gic 0 49 4>, > + <0 0 0 4 &gic 0 50 4>; > + interrupt-map-mask = <0 0 0 0x7>; > +}; > + > diff --git a/arch/arm64/boot/dts/freescale/imx8dxl.dtsi b/arch/arm64/boot/dts/freescale/imx8dxl.dtsi > index 7e54cf2028580..76de3db8b9423 100644 > --- a/arch/arm64/boot/dts/freescale/imx8dxl.dtsi > +++ b/arch/arm64/boot/dts/freescale/imx8dxl.dtsi > @@ -237,12 +237,14 @@ xtal24m: clock-xtal24m { > #include "imx8-ss-conn.dtsi" > #include "imx8-ss-ddr.dtsi" > #include "imx8-ss-lsio.dtsi" > + #include "imx8-ss-hsio.dtsi" > }; > > #include "imx8dxl-ss-adma.dtsi" > #include "imx8dxl-ss-conn.dtsi" > #include "imx8dxl-ss-lsio.dtsi" > #include "imx8dxl-ss-ddr.dtsi" > +#include "imx8dxl-ss-hsio.dtsi" > > &cm40_intmux { > interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, > diff --git a/arch/arm64/boot/dts/freescale/imx8qm-ss-hsio.dtsi b/arch/arm64/boot/dts/freescale/imx8qm-ss-hsio.dtsi > new file mode 100644 > index 0000000000000..6494f55d33f85 > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/imx8qm-ss-hsio.dtsi > @@ -0,0 +1,209 @@ > +// SPDX-License-Identifier: GPL-2.0+ > +/* > + * Copyright 2024 NXP > + * Richard Zhu <hongxing.zhu@xxxxxxx> > + */ > + > +&hsio_subsys { > + compatible = "simple-bus"; > + ranges = <0x5f000000 0x0 0x5f000000 0x21000000>, > + <0x40000000 0x0 0x60000000 0x10000000>, > + <0x80000000 0x0 0x70000000 0x10000000>; > + #address-cells = <1>; > + #size-cells = <1>; > + > + pciea: pcie@5f000000 { > + compatible = "fsl,imx8q-pcie"; > + reg = <0x5f000000 0x10000>, > + <0x4ff00000 0x80000>; > + reg-names = "dbi", "config"; > + ranges = <0x81000000 0 0x00000000 0x4ff80000 0 0x00010000>, > + <0x82000000 0 0x40000000 0x40000000 0 0x0ff00000>; > + #interrupt-cells = <1>; > + interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names = "msi"; > + #address-cells = <3>; > + #size-cells = <2>; > + clocks = <&pciea_lpcg 2>, > + <&pciea_lpcg 0>, > + <&pciea_lpcg 1>; > + clock-names = "dbi", "mstr", "slv"; > + bus-range = <0x00 0xff>; > + device_type = "pci"; > + fsl,max-link-speed = <3>; > + interrupt-map = <0 0 0 1 &gic 0 73 4>, > + <0 0 0 2 &gic 0 74 4>, > + <0 0 0 3 &gic 0 75 4>, > + <0 0 0 4 &gic 0 76 4>; > + interrupt-map-mask = <0 0 0 0x7>; > + num-lanes = <1>; > + num-viewport = <4>; > + power-domains = <&pd IMX_SC_R_PCIE_A>; > + status = "disabled"; > + }; > + > + pcieb: pcie@5f010000 { > + compatible = "fsl,imx8q-pcie"; > + reg = <0x5f010000 0x10000>, > + <0x8ff00000 0x80000>; > + reg-names = "dbi", "config"; > + ranges = <0x81000000 0 0x00000000 0x8ff80000 0 0x00010000>, > + <0x82000000 0 0x80000000 0x80000000 0 0x0ff00000>; > + #interrupt-cells = <1>; > + interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names = "msi"; > + #address-cells = <3>; > + #size-cells = <2>; > + clocks = <&pcieb_lpcg 2>, > + <&pcieb_lpcg 0>, > + <&pcieb_lpcg 1>; > + clock-names = "dbi", "mstr", "slv"; > + bus-range = <0x00 0xff>; > + device_type = "pci"; > + fsl,max-link-speed = <3>; > + interrupt-map = <0 0 0 1 &gic 0 105 4>, > + <0 0 0 2 &gic 0 106 4>, > + <0 0 0 3 &gic 0 107 4>, > + <0 0 0 4 &gic 0 108 4>; > + interrupt-map-mask = <0 0 0 0x7>; > + num-lanes = <1>; > + num-viewport = <4>; > + power-domains = <&pd IMX_SC_R_PCIE_B>; > + status = "disabled"; > + }; > + > + sata: sata@5f020000 { Not sure why SATA is included in a PCIe change. If it's been done for some reason, we should probably mention that in commit log. Shawn > + compatible = "fsl,imx8qm-ahci"; > + reg = <0x5f020000 0x10000>; > + interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&sata_lpcg 0>, > + <&sata_crr4_lpcg 0>; > + clock-names = "sata", "sata_ref"; > + /* > + * Since "REXT" pin is only present for first lane PHY > + * and its calibration result will be stored, and shared > + * by the PHY used by SATA. > + * > + * Add the calibration PHYs for SATA here, although only > + * the third lane PHY is used by SATA. > + */ > + phys = <&hsio_phy 2 PHY_TYPE_SATA 0>, > + <&hsio_phy 0 PHY_TYPE_PCIE 0>, > + <&hsio_phy 1 PHY_TYPE_PCIE 1>; > + phy-names = "sata-phy", "cali-phy0", "cali-phy1"; > + power-domains = <&pd IMX_SC_R_SATA_0>; > + status = "disabled"; > + }; > + > + pciea_lpcg: clock-controller@5f050000 { > + compatible = "fsl,imx8qxp-lpcg"; > + reg = <0x5f050000 0x10000>; > + clocks = <&hsio_axi_clk>, <&hsio_axi_clk>, <&hsio_axi_clk>; > + #clock-cells = <1>; > + clock-indices = <IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_5>, <IMX_LPCG_CLK_6>; > + clock-output-names = "hsio_pciea_mstr_axi_clk", > + "hsio_pciea_slv_axi_clk", > + "hsio_pciea_dbi_axi_clk"; > + power-domains = <&pd IMX_SC_R_PCIE_A>; > + }; > + > + sata_lpcg: clock-controller@5f070000 { > + compatible = "fsl,imx8qxp-lpcg"; > + reg = <0x5f070000 0x10000>; > + clocks = <&hsio_axi_clk>; > + #clock-cells = <1>; > + clock-indices = <IMX_LPCG_CLK_4>; > + clock-output-names = "hsio_sata_clk"; > + power-domains = <&pd IMX_SC_R_SATA_0>; > + }; > + > + phyx2_lpcg: clock-controller@5f080000 { > + compatible = "fsl,imx8qxp-lpcg"; > + reg = <0x5f080000 0x10000>; > + clocks = <&hsio_refa_clk>, <&hsio_per_clk>, > + <&hsio_refa_clk>, <&hsio_per_clk>; > + #clock-cells = <1>; > + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_1>, > + <IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_5>; > + clock-output-names = "hsio_phyx2_pclk_0", > + "hsio_phyx2_pclk_1", > + "hsio_phyx2_apbclk_0", > + "hsio_phyx2_apbclk_1"; > + power-domains = <&pd IMX_SC_R_SERDES_0>; > + }; > + > + phyx1_lpcg: clock-controller@5f090000 { > + compatible = "fsl,imx8qxp-lpcg"; > + reg = <0x5f090000 0x10000>; > + clocks = <&hsio_refa_clk>, <&hsio_per_clk>, > + <&hsio_per_clk>, <&hsio_per_clk>; > + #clock-cells = <1>; > + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_1>, > + <IMX_LPCG_CLK_2>, <IMX_LPCG_CLK_4>; > + clock-output-names = "hsio_phyx1_pclk", > + "hsio_phyx1_epcs_tx_clk", > + "hsio_phyx1_epcs_rx_clk", > + "hsio_phyx1_apb_clk"; > + power-domains = <&pd IMX_SC_R_SERDES_1>; > + }; > + > + phyx2_crr0_lpcg: clock-controller@5f0a0000 { > + compatible = "fsl,imx8qxp-lpcg"; > + reg = <0x5f0a0000 0x10000>; > + clocks = <&hsio_per_clk>; > + #clock-cells = <1>; > + clock-indices = <IMX_LPCG_CLK_4>; > + clock-output-names = "hsio_phyx2_per_clk"; > + power-domains = <&pd IMX_SC_R_SERDES_0>; > + }; > + > + pciea_crr2_lpcg: clock-controller@5f0c0000 { > + compatible = "fsl,imx8qxp-lpcg"; > + reg = <0x5f0c0000 0x10000>; > + clocks = <&hsio_per_clk>; > + #clock-cells = <1>; > + clock-indices = <IMX_LPCG_CLK_4>; > + clock-output-names = "hsio_pciea_per_clk"; > + power-domains = <&pd IMX_SC_R_PCIE_A>; > + }; > + > + sata_crr4_lpcg: clock-controller@5f0e0000 { > + compatible = "fsl,imx8qxp-lpcg"; > + reg = <0x5f0e0000 0x10000>; > + clocks = <&hsio_per_clk>; > + #clock-cells = <1>; > + clock-indices = <IMX_LPCG_CLK_4>; > + clock-output-names = "hsio_sata_per_clk"; > + power-domains = <&pd IMX_SC_R_SATA_0>; > + }; > + > + hsio_phy: phy@5f180000 { > + compatible = "fsl,imx8qm-hsio"; > + reg = <0x5f180000 0x30000>, > + <0x5f110000 0x20000>, > + <0x5f130000 0x30000>, > + <0x5f160000 0x10000>; > + reg-names = "reg", "phy", "ctrl", "misc"; > + clocks = <&phyx2_lpcg IMX_LPCG_CLK_0>, > + <&phyx2_lpcg IMX_LPCG_CLK_1>, > + <&phyx2_lpcg IMX_LPCG_CLK_4>, > + <&phyx2_lpcg IMX_LPCG_CLK_5>, > + <&phyx1_lpcg IMX_LPCG_CLK_0>, > + <&phyx1_lpcg IMX_LPCG_CLK_1>, > + <&phyx1_lpcg IMX_LPCG_CLK_2>, > + <&phyx1_lpcg IMX_LPCG_CLK_4>, > + <&phyx2_crr0_lpcg IMX_LPCG_CLK_4>, > + <&phyx1_crr1_lpcg IMX_LPCG_CLK_4>, > + <&pciea_crr2_lpcg IMX_LPCG_CLK_4>, > + <&pcieb_crr3_lpcg IMX_LPCG_CLK_4>, > + <&sata_crr4_lpcg IMX_LPCG_CLK_4>, > + <&misc_crr5_lpcg IMX_LPCG_CLK_4>; > + clock-names = "pclk0", "pclk1", "apb_pclk0", "apb_pclk1", > + "pclk2", "epcs_tx", "epcs_rx", "apb_pclk2", > + "phy0_crr", "phy1_crr", "ctl0_crr", > + "ctl1_crr", "ctl2_crr", "misc_crr"; > + #phy-cells = <3>; > + power-domains = <&pd IMX_SC_R_SERDES_0>, <&pd IMX_SC_R_SERDES_1>; > + status = "disabled"; > + }; > +}; > diff --git a/arch/arm64/boot/dts/freescale/imx8qm.dtsi b/arch/arm64/boot/dts/freescale/imx8qm.dtsi > index 3ee6e2869e3cf..ac9064a949d82 100644 > --- a/arch/arm64/boot/dts/freescale/imx8qm.dtsi > +++ b/arch/arm64/boot/dts/freescale/imx8qm.dtsi > @@ -594,6 +594,7 @@ mipi_pll_div2_clk: clock-controller-mipi-div2-pll { > #include "imx8-ss-dma.dtsi" > #include "imx8-ss-conn.dtsi" > #include "imx8-ss-lsio.dtsi" > + #include "imx8-ss-hsio.dtsi" > }; > > #include "imx8qm-ss-img.dtsi" > @@ -603,3 +604,4 @@ mipi_pll_div2_clk: clock-controller-mipi-div2-pll { > #include "imx8qm-ss-audio.dtsi" > #include "imx8qm-ss-lvds.dtsi" > #include "imx8qm-ss-mipi.dtsi" > +#include "imx8qm-ss-hsio.dtsi" > diff --git a/arch/arm64/boot/dts/freescale/imx8qxp-ss-hsio.dtsi b/arch/arm64/boot/dts/freescale/imx8qxp-ss-hsio.dtsi > new file mode 100644 > index 0000000000000..47fc6e0cff4a1 > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/imx8qxp-ss-hsio.dtsi > @@ -0,0 +1,41 @@ > +// SPDX-License-Identifier: GPL-2.0+ > +/* > + * Copyright 2024 NXP > + * Richard Zhu <hongxing.zhu@xxxxxxx> > + */ > + > +&hsio_subsys { > + phyx1_lpcg: clock-controller@5f090000 { > + compatible = "fsl,imx8qxp-lpcg"; > + reg = <0x5f090000 0x10000>; > + clocks = <&hsio_refb_clk>, <&hsio_per_clk>, > + <&hsio_per_clk>, <&hsio_per_clk>; > + #clock-cells = <1>; > + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_1>, > + <IMX_LPCG_CLK_2>, <IMX_LPCG_CLK_4>; > + clock-output-names = "hsio_phyx1_pclk", > + "hsio_phyx1_epcs_tx_clk", > + "hsio_phyx1_epcs_rx_clk", > + "hsio_phyx1_apb_clk"; > + power-domains = <&pd IMX_SC_R_SERDES_1>; > + }; > + > + hsio_phy: phy@5f1a0000 { > + compatible = "fsl,imx8qxp-hsio"; > + reg = <0x5f1a0000 0x10000>, > + <0x5f120000 0x10000>, > + <0x5f140000 0x10000>, > + <0x5f160000 0x10000>; > + reg-names = "reg", "phy", "ctrl", "misc"; > + clocks = <&phyx1_lpcg IMX_LPCG_CLK_0>, > + <&phyx1_lpcg IMX_LPCG_CLK_1>, > + <&phyx1_crr1_lpcg IMX_LPCG_CLK_4>, > + <&pcieb_crr3_lpcg IMX_LPCG_CLK_4>, > + <&misc_crr5_lpcg IMX_LPCG_CLK_4>; > + clock-names = "pclk0", "apb_pclk0", "phy0_crr", "ctl0_crr", > + "misc_crr"; > + #phy-cells = <3>; > + power-domains = <&pd IMX_SC_R_SERDES_1>; > + status = "disabled"; > + }; > +}; > diff --git a/arch/arm64/boot/dts/freescale/imx8qxp.dtsi b/arch/arm64/boot/dts/freescale/imx8qxp.dtsi > index 0313f295de2e9..db21c6d64f24d 100644 > --- a/arch/arm64/boot/dts/freescale/imx8qxp.dtsi > +++ b/arch/arm64/boot/dts/freescale/imx8qxp.dtsi > @@ -323,6 +323,7 @@ map0 { > #include "imx8-ss-conn.dtsi" > #include "imx8-ss-ddr.dtsi" > #include "imx8-ss-lsio.dtsi" > + #include "imx8-ss-hsio.dtsi" > }; > > #include "imx8qxp-ss-img.dtsi" > @@ -330,3 +331,4 @@ map0 { > #include "imx8qxp-ss-adma.dtsi" > #include "imx8qxp-ss-conn.dtsi" > #include "imx8qxp-ss-lsio.dtsi" > +#include "imx8qxp-ss-hsio.dtsi" > -- > 2.34.1 >