On Sat, Oct 19, 2024 at 01:50:49PM +0200, Barnabás Czémán wrote:
> From: Otto Pflüger <otto.pflueger@xxxxxxxxx>
>
> Add initial support for MSM8917 SoC.
>
> Signed-off-by: Otto Pflüger <otto.pflueger@xxxxxxxxx>
> [reword commit, rebase, fix schema errors]
> Signed-off-by: Barnabás Czémán <barnabas.czeman@xxxxxxxxxxxxxx>
> ---
> arch/arm64/boot/dts/qcom/msm8917-pins.dtsi | 344 ++++++
> arch/arm64/boot/dts/qcom/msm8917.dtsi | 1557 ++++++++++++++++++++++++++++
> arch/arm64/boot/dts/qcom/pm8916.dtsi | 9 +-
> 3 files changed, 1909 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/msm8917-pins.dtsi b/arch/arm64/boot/dts/qcom/msm8917-pins.dtsi
> new file mode 100644
> index 0000000000000000000000000000000000000000..f283ffd59b8aca8e510ef95d5526af9592a1c036
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/msm8917-pins.dtsi
Please merge into msm8917.dtsi (for generic parts) and
msm8917-boatd.dtsi (for board-specific parts).
> @@ -0,0 +1,344 @@
> +// SPDX-License-Identifier: GPL-2.0
If possible, GPL-2.0 OR MIT, or GPL-2.0 OR BSD-2/3-Clause
> +&tlmm {
> + blsp1_uart1_default: blsp1-uart1-default-state {
> + pins = "gpio0", "gpio1", "gpio2", "gpio3";
> + function = "blsp_uart1";
> +
> + drive-strength = <16>;
> + bias-disable;
> + };
> +
> + blsp1_uart1_sleep: blsp1-uart1-sleep-state {
> + pins = "gpio0", "gpio1", "gpio2", "gpio3";
> + function = "gpio";
> +
> + drive-strength = <2>;
> + bias-pull-down;
> + };
Please sort all the pin states by the node name.
> +
> + wcnss_pin_a: wcnss-active-state {
> + wcss-wlan2-pins {
> + pins = "gpio76";
> + function = "wcss_wlan2";
> + drive-strength = <6>;
> + bias-pull-up;
> +
> + };
> +
> + wcss-wlan1-pins {
and subnodes too.
> + pins = "gpio77";
> + function = "wcss_wlan1";
> + drive-strength = <6>;
> + bias-pull-up;
> +
> + };
> +
> + wcss-wlan0-pins {
> + pins = "gpio78";
> + function = "wcss_wlan0";
> + drive-strength = <6>;
> + bias-pull-up;
> +
> + };
> +
> + wcss-wlan-pins {
> + pins = "gpio79", "gpio80";
> + function = "wcss_wlan";
> + drive-strength = <6>;
> + bias-pull-up;
> +
> + };
> + };
> +
> + cci0_default: cci0-default-state {
> + pins = "gpio29", "gpio30";
> + function = "cci_i2c";
> +
> +
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + cci1_default: cci1-default-state {
> + pins = "gpio31", "gpio32";
> + function = "cci_i2c";
> +
> +
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + cdc_pdm_lines_act: pdm-lines-on-state {
> + pins = "gpio69", "gpio70", "gpio71", "gpio72",
> + "gpio73", "gpio74";
> + function = "cdc_pdm0";
> +
> + drive-strength = <8>;
> + bias-disable;
> + };
> +
> + cdc_pdm_lines_sus: pdm-lines-off-state {
> + pins = "gpio69", "gpio70", "gpio71", "gpio72",
> + "gpio73", "gpio74";
> + function = "cdc_pdm0";
> +
> + drive-strength = <2>;
> + bias-disable;
> + };
> +};
> diff --git a/arch/arm64/boot/dts/qcom/msm8917.dtsi b/arch/arm64/boot/dts/qcom/msm8917.dtsi
> new file mode 100644
> index 0000000000000000000000000000000000000000..e5f580c6ec28ad6442b31a0e1ee256c376c5438d
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/msm8917.dtsi
> @@ -0,0 +1,1557 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +
> +#include <dt-bindings/clock/qcom,gcc-msm8917.h>
> +#include <dt-bindings/clock/qcom,rpmcc.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/power/qcom-rpmpd.h>
> +#include <dt-bindings/soc/qcom,apr.h>
> +#include <dt-bindings/sound/qcom,q6dsp-lpass-ports.h>
> +#include <dt-bindings/thermal/thermal.h>
> +
> +/ {
> + interrupt-parent = <&intc>;
> +
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + aliases {
> + mmc0 = &sdhc_1; /* SDC1 eMMC slot */
> + mmc1 = &sdhc_2; /* SDC2 SD card slot */
> + };
> +
> + chosen { };
> +
> + memory@80000000 {
> + device_type = "memory";
> + /* We expect the bootloader to fill in the reg */
> + reg = <0 0x80000000 0 0>;
> + };
> +
> + reserved-memory {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + reserved@85b00000 {
> + reg = <0x0 0x85b00000 0x0 0x800000>;
> + no-map;
> + };
> +
> + smem@86300000 {
> + compatible = "qcom,smem";
> + reg = <0x0 0x86300000 0x0 0x100000>;
> + no-map;
> +
> + hwlocks = <&tcsr_mutex 3>;
> + qcom,rpm-msg-ram = <&rpm_msg_ram>;
> + };
> +
> + reserved@86400000 {
> + reg = <0x0 0x86400000 0x0 0x400000>;
> + no-map;
> + };
> +
> + mpss_mem: mpss@86800000 {
> + /*
> + * The memory region for the mpss firmware is generally
> + * relocatable and could be allocated dynamically.
> + * However, many firmware versions tend to fail when
> + * loaded to some special addresses, so it is hard to
> + * define reliable alloc-ranges.
> + *
> + * alignment = <0x0 0x400000>;
> + * alloc-ranges = <0x0 0x86800000 0x0 0x8000000>;
> + */
> + reg = <0x0 0x86800000 0x0 0>; /* size is device-specific */
> + no-map;
> + status = "disabled";
> + };
> +
> + adsp_mem: adsp {
> + size = <0x0 0x1100000>;
> + alignment = <0x0 0x100000>;
> + alloc-ranges = <0x0 0x86800000 0x0 0x8000000>;
> + no-map;
> + status = "disabled";
> + };
> +
> + wcnss_mem: wcnss {
> + size = <0x0 0x700000>;
> + alignment = <0x0 0x100000>;
> + alloc-ranges = <0x0 0x86800000 0x0 0x8000000>;
> + no-map;
> + status = "disabled";
> + };
> +
> + venus_mem: venus {
> + size = <0x0 0x400000>;
> + alignment = <0x0 0x100000>;
> + alloc-ranges = <0x0 0x86800000 0x0 0x8000000>;
> + no-map;
> + status = "disabled";
> + };
> +
> + mba_mem: mba {
Please sort these nodes too.
> + size = <0x0 0x100000>;
> + alignment = <0x0 0x100000>;
> + alloc-ranges = <0x0 0x86800000 0x0 0x8000000>;
> + no-map;
> + status = "disabled";
> + };
> +
> + rmtfs@92100000 {
This one should be after mpss_mem, just before adsp.
> + compatible = "qcom,rmtfs-mem";
> + reg = <0x0 0x92100000 0x0 0x180000>;
> + no-map;
> +
> + qcom,client-id = <1>;
> + };
> + };
> +
> + cpus {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + CPU0: cpu@0 {
lowercase all labels.
> + device_type = "cpu";
> + compatible = "arm,cortex-a53";
> + reg = <0x100>;
> + next-level-cache = <&L2_0>;
> + enable-method = "psci";
> + clocks = <&apcs>;
> + operating-points-v2 = <&cpu_opp_table>;
> + #cooling-cells = <2>;
> + power-domains = <&CPU_PD0>;
> + power-domain-names = "psci";
> + };
> +
> + CPU1: cpu@1 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53";
> + reg = <0x101>;
> + next-level-cache = <&L2_0>;
> + enable-method = "psci";
> + clocks = <&apcs>;
> + operating-points-v2 = <&cpu_opp_table>;
> + #cooling-cells = <2>;
> + power-domains = <&CPU_PD1>;
> + power-domain-names = "psci";
> + };
> +
> + CPU2: cpu@2 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53";
> + reg = <0x102>;
> + next-level-cache = <&L2_0>;
> + enable-method = "psci";
> + clocks = <&apcs>;
> + operating-points-v2 = <&cpu_opp_table>;
> + #cooling-cells = <2>;
> + power-domains = <&CPU_PD2>;
> + power-domain-names = "psci";
> + };
> +
> + CPU3: cpu@3 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53";
> + reg = <0x103>;
> + next-level-cache = <&L2_0>;
> + enable-method = "psci";
> + clocks = <&apcs>;
> + operating-points-v2 = <&cpu_opp_table>;
> + #cooling-cells = <2>;
> + power-domains = <&CPU_PD3>;
> + power-domain-names = "psci";
> + };
> +
> + L2_0: l2-cache {
> + compatible = "cache";
> + cache-level = <2>;
> + cache-unified;
> + };
> +
> + cpu-map {
> + cluster0 {
> + core0 {
> + cpu = <&CPU0>;
> + };
> +
> + core1 {
> + cpu = <&CPU1>;
> + };
> +
> + core2 {
> + cpu = <&CPU2>;
> + };
> +
> + core3 {
> + cpu = <&CPU3>;
> + };
> + };
> + };
> +
> + idle-states {
> + entry-method = "psci";
> +
> + CPU_SLEEP_0: cpu-sleep-0 {
> + compatible = "arm,idle-state";
> + idle-state-name = "standalone-power-collapse";
> + arm,psci-suspend-param = <0x40000003>;
> + entry-latency-us = <125>;
> + exit-latency-us = <180>;
> + min-residency-us = <595>;
> + local-timer-stop;
> + };
> + };
> +
> + domain-idle-states {
> + CLUSTER_PWRDN: cluster-gdhs {
> + compatible = "domain-idle-state";
> + arm,psci-suspend-param = <0x41000043>;
> + entry-latency-us = <240>;
> + exit-latency-us = <280>;
> + min-residency-us = <806>;
> + };
> +
> + CLUSTER_RET: cluster-retention {
> + compatible = "domain-idle-state";
> + arm,psci-suspend-param = <0x41000023>;
> + entry-latency-us = <700>;
> + exit-latency-us = <650>;
> + min-residency-us = <1972>;
> + };
> +
> + CLUSTER_PC: cluster-power-collapse {
> + compatible = "domain-idle-state";
> + arm,psci-suspend-param = <0x41000053>;
> + entry-latency-us = <700>;
> + exit-latency-us = <1000>;
> + min-residency-us = <6500>;
> + };
> + };
> + };
> +
> + cpu_opp_table: opp-table-cpu {
> + compatible = "operating-points-v2";
> + opp-shared;
> +
> + opp-960000000 {
> + opp-hz = /bits/ 64 <960000000>;
> + };
> +
> + opp-1094400000 {
> + opp-hz = /bits/ 64 <1094400000>;
> + };
> +
> + opp-1248000000 {
> + opp-hz = /bits/ 64 <1248000000>;
> + };
> +
> + opp-1401600000 {
> + opp-hz = /bits/ 64 <1401600000>;
> + };
> + };
> +
> + timer {
Again, please sort the nodes.
> + compatible = "arm,armv8-timer";
> + interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
> + clock-frequency = <19200000>;
> + };
> +
> + clocks {
> + xo_board: xo-board {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <19200000>;
> + clock-output-names = "xo";
Freq goes to the board dts.
Please drop clock-output-names.
> + };
> +
> + sleep_clk: sleep-clk {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <32768>;
> + clock-output-names = "sleep_clk";
> + };
> + };
> +
> + firmware {
> + scm: scm {
> + compatible = "qcom,scm-msm8916", "qcom,scm";
> + clocks = <&gcc GCC_CRYPTO_CLK>,
> + <&gcc GCC_CRYPTO_AXI_CLK>,
> + <&gcc GCC_CRYPTO_AHB_CLK>;
> + clock-names = "core", "bus", "iface";
> + #reset-cells = <1>;
> +
> + qcom,dload-mode = <&tcsr 0x6100>;
> + };
> + };
> +
> + pmu {
> + compatible = "arm,cortex-a53-pmu";
> + interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
> + };
> +
> + psci {
> + compatible = "arm,psci-1.0";
> + method = "smc";
> +
> + CPU_PD0: power-domain-cpu0 {
> + #power-domain-cells = <0>;
> + power-domains = <&CLUSTER_PD>;
> + domain-idle-states = <&CPU_SLEEP_0>;
> + };
> +
> + CPU_PD1: power-domain-cpu1 {
> + #power-domain-cells = <0>;
> + power-domains = <&CLUSTER_PD>;
> + domain-idle-states = <&CPU_SLEEP_0>;
> + };
> +
> + CPU_PD2: power-domain-cpu2 {
> + #power-domain-cells = <0>;
> + power-domains = <&CLUSTER_PD>;
> + domain-idle-states = <&CPU_SLEEP_0>;
> + };
> +
> + CPU_PD3: power-domain-cpu3 {
> + #power-domain-cells = <0>;
> + power-domains = <&CLUSTER_PD>;
> + domain-idle-states = <&CPU_SLEEP_0>;
> + };
> +
> + CLUSTER_PD: power-domain-cluster {
> + #power-domain-cells = <0>;
> + domain-idle-states = <&CLUSTER_PWRDN>, <&CLUSTER_RET>, <&CLUSTER_PC>;
> + };
> + };
> +
> + rpm: remoteproc {
> + compatible = "qcom,msm8917-rpm-proc", "qcom,rpm-proc";
> +
> + smd-edge {
> + interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
> + qcom,ipc = <&apcs 8 0>;
> + qcom,smd-edge = <15>;
> +
> + rpm_requests: rpm-requests {
> + compatible = "qcom,rpm-msm8917", "qcom,smd-rpm";
> + qcom,smd-channels = "rpm_requests";
> +
> + rpmcc: clock-controller {
> + compatible = "qcom,rpmcc-msm8917", "qcom,rpmcc";
> + #clock-cells = <1>;
> + clocks = <&xo_board>;
> + clock-names = "xo";
> + };
> +
> + rpmpd: power-controller {
> + compatible = "qcom,msm8917-rpmpd";
> + #power-domain-cells = <1>;
> + operating-points-v2 = <&rpmpd_opp_table>;
> +
> + rpmpd_opp_table: opp-table {
> + compatible = "operating-points-v2";
> +
> + rpmpd_opp_ret: opp1 {
> + opp-level = <RPM_SMD_LEVEL_RETENTION>;
> + };
> +
> + rpmpd_opp_ret_plus: opp2 {
> + opp-level = <RPM_SMD_LEVEL_RETENTION_PLUS>;
> + };
> +
> + rpmpd_opp_min_svs: opp3 {
> + opp-level = <RPM_SMD_LEVEL_MIN_SVS>;
> + };
> +
> + rpmpd_opp_low_svs: opp4 {
> + opp-level = <RPM_SMD_LEVEL_LOW_SVS>;
> + };
> +
> + rpmpd_opp_svs: opp5 {
> + opp-level = <RPM_SMD_LEVEL_SVS>;
> + };
> +
> + rpmpd_opp_svs_plus: opp6 {
> + opp-level = <RPM_SMD_LEVEL_SVS_PLUS>;
> + };
> +
> + rpmpd_opp_nom: opp7 {
> + opp-level = <RPM_SMD_LEVEL_NOM>;
> + };
> +
> + rpmpd_opp_nom_plus: opp8 {
> + opp-level = <RPM_SMD_LEVEL_NOM_PLUS>;
> + };
> +
> + rpmpd_opp_turbo: opp9 {
> + opp-level = <RPM_SMD_LEVEL_TURBO>;
> + };
> + };
> + };
> + };
> + };
> + };
> +
> + smp2p-adsp {
> + compatible = "qcom,smp2p";
> + qcom,smem = <443>, <429>;
> +
> + interrupts = <GIC_SPI 291 IRQ_TYPE_EDGE_RISING>;
> +
> + mboxes = <&apcs 10>;
> +
> + qcom,local-pid = <0>;
> + qcom,remote-pid = <2>;
> +
> + adsp_smp2p_out: master-kernel {
> + qcom,entry-name = "master-kernel";
> +
> + #qcom,smem-state-cells = <1>;
> + };
> +
> + adsp_smp2p_in: slave-kernel {
> + qcom,entry-name = "slave-kernel";
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> + };
> +
> + smp2p-modem {
> + compatible = "qcom,smp2p";
> + qcom,smem = <435>, <428>;
> +
> + interrupts = <GIC_SPI 27 IRQ_TYPE_EDGE_RISING>;
> +
> + qcom,ipc = <&apcs 8 14>;
> +
> + qcom,local-pid = <0>;
> + qcom,remote-pid = <1>;
> +
> + modem_smp2p_out: master-kernel {
> + qcom,entry-name = "master-kernel";
> +
> + #qcom,smem-state-cells = <1>;
> + };
> +
> + modem_smp2p_in: slave-kernel {
> + qcom,entry-name = "slave-kernel";
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> + };
> +
> + smp2p-wcnss {
> + compatible = "qcom,smp2p";
> + qcom,smem = <451>, <431>;
> +
> + interrupts = <GIC_SPI 143 IRQ_TYPE_EDGE_RISING>;
> +
> + qcom,ipc = <&apcs 8 18>;
> +
> + qcom,local-pid = <0>;
> + qcom,remote-pid = <4>;
> +
> + wcnss_smp2p_out: master-kernel {
> + qcom,entry-name = "master-kernel";
> +
> + #qcom,smem-state-cells = <1>;
> + };
> +
> + wcnss_smp2p_in: slave-kernel {
> + qcom,entry-name = "slave-kernel";
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> + };
> +
> + smsm {
> + compatible = "qcom,smsm";
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + qcom,ipc-1 = <&apcs 8 13>;
> + qcom,ipc-3 = <&apcs 8 19>;
Please use mboxes instead
> +
> + apps_smsm: apps@0 {
> + reg = <0>;
> +
> + #qcom,smem-state-cells = <1>;
> + };
> +
> + hexagon_smsm: hexagon@1 {
> + reg = <1>;
> + interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + wcnss_smsm: wcnss@6 {
> + reg = <6>;
> + interrupts = <GIC_SPI 144 IRQ_TYPE_EDGE_RISING>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> + };
> +
> + soc: soc@0 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges = <0 0 0 0xffffffff>;
> + compatible = "simple-bus";
> +
> + rng@22000 {
> + compatible = "qcom,prng";
> + reg = <0xe3000 0x1000>;
> + clocks = <&gcc GCC_PRNG_AHB_CLK>;
> + clock-names = "core";
> + };
> +
> + restart@4ab000 {
> + compatible = "qcom,pshold";
> + reg = <0x004ab000 0x4>;
> + };
> +
> + qfprom: qfprom@a4000 {
> + compatible = "qcom,msm8917-qfprom", "qcom,qfprom";
> + reg = <0x000a4000 0x1000>;
> + #address-cells = <1>;
> + #size-cells = <1>;
empty line
> + tsens_caldata: caldata@d0 {
> + reg = <0x01d8 0x14>;
> + };
No, individual bit definitions for each of tsens fuse values.
> + };
> +
> + rpm_msg_ram: sram@60000 {
> + compatible = "qcom,rpm-msg-ram";
> + reg = <0x00060000 0x8000>;
> + };
> +
> + tsens: thermal-sensor@4a9000 {
> + compatible = "qcom,msm8917-tsens", "qcom,tsens-v1";
> + reg = <0x004a9000 0x1000>,
> + <0x004a8000 0x1000>;
> + nvmem-cells = <&tsens_caldata>;
> + nvmem-cell-names = "calib";
And here too, individual bits instead of a single blob.
> + #qcom,sensors = <10>;
> + interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "uplow";
> + #thermal-sensor-cells = <1>;
> + };
> +
> + tlmm: pinctrl@1000000 {
> + compatible = "qcom,msm8917-pinctrl";
> + reg = <0x01000000 0x300000>;
> + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
> + gpio-controller;
> + gpio-ranges = <&tlmm 0 0 134>;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + gcc: clock-controller@1800000 {
> + compatible = "qcom,gcc-msm8917";
> + #clock-cells = <1>;
> + #reset-cells = <1>;
> + #power-domain-cells = <1>;
> + reg = <0x01800000 0x80000>;
> + clocks = <&xo_board>,
> + <&sleep_clk>,
> + <&mdss_dsi0_phy 1>,
> + <&mdss_dsi0_phy 0>;
> + clock-names = "xo",
> + "sleep_clk",
> + "dsi0pll",
> + "dsi0pllbyte";
> + };
> +
> + tcsr_mutex: hwlock@1905000 {
> + compatible = "qcom,tcsr-mutex";
> + reg = <0x01905000 0x20000>;
> + #hwlock-cells = <1>;
> + };
> +
> + tcsr: syscon@1937000 {
> + compatible = "qcom,tcsr-msm8917", "syscon";
> + reg = <0x01937000 0x30000>;
> + };
> +
> + apps_iommu: iommu@1e00000 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + #iommu-cells = <1>;
> + compatible = "qcom,msm8917-iommu", "qcom,msm-iommu-v1";
> + ranges = <0 0x01e20000 0x20000>;
> +
> + clocks = <&gcc GCC_SMMU_CFG_CLK>,
> + <&gcc GCC_APSS_TCU_CLK>;
> + clock-names = "iface", "bus";
> +
> + qcom,iommu-secure-id = <17>;
> +
> + /* VFE */
> + iommu-ctx@14000 {
> + compatible = "qcom,msm-iommu-v1-ns";
> + reg = <0x00014000 0x1000>;
> + interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + /* MDP_0 */
> + iommu-ctx@15000 {
> + compatible = "qcom,msm-iommu-v1-ns";
> + reg = <0x00015000 0x1000>;
> + interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + /* VENUS_NS */
> + iommu-ctx@16000 {
> + compatible = "qcom,msm-iommu-v1-ns";
> + reg = <0x00016000 0x1000>;
> + interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
> + };
> + };
> +
> + gpu_iommu: iommu@1f00000 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + #iommu-cells = <1>;
> +
> + compatible = "qcom,msm8917-iommu", "qcom,msm-iommu-v1";
> +
> + ranges = <0 0x01f08000 0x10000>;
> + clocks = <&gcc GCC_SMMU_CFG_CLK>,
> + <&gcc GCC_GFX_TCU_CLK>;
> + clock-names = "iface", "bus";
> + qcom,iommu-secure-id = <18>;
> +
> + iommu-ctx@0 {
> + compatible = "qcom,msm-iommu-v2-ns";
> + reg = <0x0000 0x1000>;
> + interrupts = <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>;
> + };
> + };
> +
> + mdss: display-subsystem@1a00000 {
Please keep the nodes sorted by the address.
> + compatible = "qcom,mdss";
> + reg = <0x01a00000 0x1000>,
> + <0x01ab0000 0x1040>;
> + reg-names = "mdss_phys", "vbif_phys";
> +
> + power-domains = <&gcc MDSS_GDSC>;
> +
> + clocks = <&gcc GCC_MDSS_AHB_CLK>,
> + <&gcc GCC_MDSS_AXI_CLK>,
> + <&gcc GCC_MDSS_VSYNC_CLK>;
> + clock-names = "iface",
> + "bus",
> + "vsync";
> +
> + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
> +
> + interrupt-controller;
> + #interrupt-cells = <1>;
> +
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + status = "disabled";
> +
> + mdp: display-controller@1a01000 {
> + compatible = "qcom,msm8917-mdp5", "qcom,mdp5";
> + reg = <0x01a01000 0x89000>;
> + reg-names = "mdp_phys";
> +
> + interrupt-parent = <&mdss>;
> + interrupts = <0>;
> +
> + power-domains = <&gcc MDSS_GDSC>;
> +
> + clocks = <&gcc GCC_MDSS_AHB_CLK>,
> + <&gcc GCC_MDSS_AXI_CLK>,
> + <&gcc GCC_MDSS_MDP_CLK>,
> + <&gcc GCC_MDSS_VSYNC_CLK>;
> + clock-names = "iface",
> + "bus",
> + "core",
> + "vsync";
> +
> + iommus = <&apps_iommu 0x15>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
Please add missing empty lines between properties and subnodes.
> + mdp5_intf1_out: endpoint {
mdss_mdp_intf1_out:
> + remote-endpoint = <&mdss_dsi0_in>;
> + };
> + };
> + };
> + };
> +
> + mdss_dsi0: dsi@1a94000 {
> + compatible = "qcom,mdss-dsi-ctrl";
> + reg = <0x01a94000 0x300>;
> + reg-names = "dsi_ctrl";
> +
> + interrupt-parent = <&mdss>;
> + interrupts = <4>;
> +
> + assigned-clocks = <&gcc BYTE0_CLK_SRC>,
> + <&gcc PCLK0_CLK_SRC>;
> + assigned-clock-parents = <&mdss_dsi0_phy 0>,
> + <&mdss_dsi0_phy 1>;
> +
> + clocks = <&gcc GCC_MDSS_MDP_CLK>,
> + <&gcc GCC_MDSS_AHB_CLK>,
> + <&gcc GCC_MDSS_AXI_CLK>,
> + <&gcc GCC_MDSS_BYTE0_CLK>,
> + <&gcc GCC_MDSS_PCLK0_CLK>,
> + <&gcc GCC_MDSS_ESC0_CLK>;
> + clock-names = "mdp_core",
> + "iface",
> + "bus",
> + "byte",
> + "pixel",
> + "core";
> + phys = <&mdss_dsi0_phy>;
> +
> + operating-points-v2 = <&mdss_dsi0_opp_table>;
> + power-domains = <&rpmpd MSM8917_VDDCX>;
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + mdss_dsi0_in: endpoint {
> + remote-endpoint = <&mdp5_intf1_out>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> + mdss_dsi0_out: endpoint {
> + };
> + };
> + };
> +
> + mdss_dsi0_opp_table: opp-table {
> + compatible = "operating-points-v2";
> +
> + opp-125000000 {
> + opp-hz = /bits/ 64 <125000000>;
> + required-opps = <&rpmpd_opp_svs>;
> + };
> +
> + opp-187500000 {
> + opp-hz = /bits/ 64 <187500000>;
> + required-opps = <&rpmpd_opp_nom>;
> + };
> + };
> + };
> +
> + mdss_dsi0_phy: phy@1a94400 {
> + compatible = "qcom,dsi-phy-28nm-8937";
> + reg = <0x01a94a00 0xd4>,
> + <0x01a94400 0x280>,
> + <0x01a94b80 0x30>;
> + reg-names = "dsi_pll",
> + "dsi_phy",
> + "dsi_phy_regulator";
> +
> + #clock-cells = <1>;
> + #phy-cells = <0>;
> +
> + clocks = <&gcc GCC_MDSS_AHB_CLK>,
> + <&xo_board>;
> + clock-names = "iface", "ref";
> + };
> + };
> +
> + a53pll: clock@b016000 {
> + compatible = "qcom,msm8939-a53pll";
> + reg = <0x0b016000 0x40>;
> + clocks = <&xo_board>;
> + clock-names = "xo";
> + #clock-cells = <0>;
> + operating-points-v2 = <&pll_opp_table>;
> +
> + pll_opp_table: opp-table {
> + compatible = "operating-points-v2";
> +
> + opp-960000000 {
> + opp-hz = /bits/ 64 <960000000>;
> + };
> +
> + opp-1094400000 {
> + opp-hz = /bits/ 64 <1094400000>;
> + };
> +
> + opp-1248000000 {
> + opp-hz = /bits/ 64 <1248000000>;
> + };
> +
> + opp-1401600000 {
> + opp-hz = /bits/ 64 <1401600000>;
> + };
> + };
> + };
> +
> + gpu: gpu@1c00000 {
> + compatible = "qcom,adreno-306.32", "qcom,adreno";
Is it really .32 ?
> + reg = <0x01c00000 0x20000>;
> + reg-names = "kgsl_3d0_reg_memory";
> + interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "kgsl_3d0_irq";
> + clock-names = "core",
> + "iface",
> + "mem_iface",
> + "alt_mem_iface",
> + "gfx3d";
> + clocks = <&gcc GCC_OXILI_GFX3D_CLK>,
> + <&gcc GCC_OXILI_AHB_CLK>,
> + <&gcc GCC_BIMC_GFX_CLK>,
> + <&gcc GCC_BIMC_GPU_CLK>,
> + <&gcc GFX3D_CLK_SRC>;
> + power-domains = <&gcc OXILI_GX_GDSC>;
> + operating-points-v2 = <&gpu_opp_table>;
> + #cooling-cells = <2>;
> +
> + iommus = <&gpu_iommu 0>;
> +
> + status = "disabled";
> +
> + gpu_opp_table: opp-table {
> + compatible = "operating-points-v2";
> +
> + opp-598000000 {
> + opp-hz = /bits/ 64 <598000000>;
> + };
> +
> + opp-523200000 {
> + opp-hz = /bits/ 64 <523200000>;
> + };
> +
> + opp-484800000 {
> + opp-hz = /bits/ 64 <484800000>;
> + };
> +
> + opp-400000000 {
> + opp-hz = /bits/ 64 <400000000>;
> + };
> +
> + opp-270000000 {
> + opp-hz = /bits/ 64 <270000000>;
> + };
> +
> + opp-19200000 {
> + opp-hz = /bits/ 64 <19200000>;
> + };
> + };
> + };
> +
> + spmi_bus: spmi@200f000 {
> + compatible = "qcom,spmi-pmic-arb";
> + reg = <0x0200f000 0x001000>,
> + <0x02400000 0x800000>,
> + <0x02c00000 0x800000>,
> + <0x03800000 0x200000>,
> + <0x0200a000 0x002100>;
> + reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
> + interrupt-names = "periph_irq";
> + interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
> + qcom,ee = <0>;
> + qcom,channel = <0>;
> + #address-cells = <2>;
> + #size-cells = <0>;
> + interrupt-controller;
> + #interrupt-cells = <4>;
> + };
> +
> + bam_dmux_dma: dma-controller@4044000 {
> + compatible = "qcom,bam-v1.7.0";
> + reg = <0x04044000 0x19000>;
> + interrupts = <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>;
> + #dma-cells = <1>;
> + qcom,ee = <0>;
> +
> + num-channels = <6>;
> + qcom,num-ees = <1>;
> + qcom,powered-remotely;
> +
> + status = "disabled";
> + };
> +
> + apcs: mailbox@b011000 {
> + compatible = "qcom,msm8939-apcs-kpss-global", "syscon";
> + reg = <0x0b011000 0x1000>;
> + #mbox-cells = <1>;
> + clocks = <&a53pll>, <&gcc GPLL0_EARLY>, <&rpmcc RPM_SMD_XO_CLK_SRC>;
> + clock-names = "pll", "aux", "ref";
> + #clock-cells = <0>;
> + };
> +
> + sdhc_1: mmc@7824900 {
> + compatible = "qcom,sdhci-msm-v4";
> + reg = <0x07824900 0x500>, <0x07824000 0x800>;
> + reg-names = "hc", "core";
> +
> + interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "hc_irq", "pwr_irq";
> + clocks = <&gcc GCC_SDCC1_AHB_CLK>,
> + <&gcc GCC_SDCC1_APPS_CLK>,
> + <&xo_board>;
> + clock-names = "iface", "core", "xo";
> + power-domains = <&rpmpd MSM8917_VDDCX>;
> + mmc-hs200-1_8v;
> + mmc-hs400-1_8v;
> + mmc-ddr-1_8v;
> + bus-width = <8>;
> + non-removable;
> + status = "disabled";
> + };
> +
> + sdhc_2: mmc@7864900 {
> + compatible = "qcom,sdhci-msm-v4";
> + reg = <0x07864900 0x500>, <0x07864000 0x800>;
> + reg-names = "hc", "core";
> +
> + interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "hc_irq", "pwr_irq";
> + clocks = <&gcc GCC_SDCC2_AHB_CLK>,
> + <&gcc GCC_SDCC2_APPS_CLK>,
> + <&xo_board>;
> + clock-names = "iface", "core", "xo";
> + power-domains = <&rpmpd MSM8917_VDDCX>;
> + bus-width = <4>;
> + status = "disabled";
> + };
> +
> + blsp1_dma: dma-controller@7884000 {
> + compatible = "qcom,bam-v1.7.0";
> + reg = <0x07884000 0x1f000>;
> + interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_BLSP1_AHB_CLK>;
> + clock-names = "bam_clk";
> + qcom,controlled-remotely;
> + #dma-cells = <1>;
> + num-channels = <12>;
> + qcom,num-ees = <4>;
> + qcom,ee = <0>;
> + };
> +
> + blsp2_dma: dma-controller@7ac4000 {
> + compatible = "qcom,bam-v1.7.0";
> + reg = <0x07ac4000 0x1d000>;
> + interrupts = <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_BLSP2_AHB_CLK>;
> + clock-names = "bam_clk";
> + qcom,controlled-remotely;
> + #dma-cells = <1>;
> + num-channels = <10>;
> + qcom,num-ees = <4>;
> + qcom,ee = <0>;
> + };
> +
> + blsp1_uart1: serial@78af000 {
> + compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
> + reg = <0x078af000 0x200>;
> + interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>,
> + <&gcc GCC_BLSP1_AHB_CLK>;
> + clock-names = "core", "iface";
> + dmas = <&blsp1_dma 0>, <&blsp1_dma 1>;
> + dma-names = "tx", "rx";
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&blsp1_uart1_default>;
> + pinctrl-1 = <&blsp1_uart1_sleep>;
> + status = "disabled";
> + };
> +
> + blsp1_uart2: serial@78b0000 {
> + compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
> + reg = <0x078b0000 0x200>;
> + interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>,
> + <&gcc GCC_BLSP1_AHB_CLK>;
> + clock-names = "core", "iface";
> + dmas = <&blsp1_dma 2>, <&blsp1_dma 3>;
> + dma-names = "tx", "rx";
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&blsp1_uart2_default>;
> + pinctrl-1 = <&blsp1_uart2_sleep>;
> + status = "disabled";
> + };
> +
> + blsp_i2c2: i2c@78b6000 {
> + compatible = "qcom,i2c-qup-v2.2.1";
> + reg = <0x078b6000 0x600>;
> + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>,
> + <&gcc GCC_BLSP1_AHB_CLK>;
> + clock-names = "core", "iface";
> + dmas = <&blsp1_dma 6>, <&blsp1_dma 7>;
> + dma-names = "tx", "rx";
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&i2c2_default>;
> + pinctrl-1 = <&i2c2_sleep>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + blsp_i2c3: i2c@78b7000 {
> + compatible = "qcom,i2c-qup-v2.2.1";
> + reg = <0x078b7000 0x600>;
> + interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>,
> + <&gcc GCC_BLSP1_AHB_CLK>;
> + clock-names = "core", "iface";
> + dmas = <&blsp1_dma 8>, <&blsp1_dma 9>;
> + dma-names = "tx", "rx";
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&i2c3_default>;
> + pinctrl-1 = <&i2c3_sleep>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + blsp_spi3: spi@78b7000 {
> + compatible = "qcom,spi-qup-v2.2.1";
> + reg = <0x078b7000 0x600>;
> + interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_BLSP1_QUP3_SPI_APPS_CLK>,
> + <&gcc GCC_BLSP1_AHB_CLK>;
> + clock-names = "core", "iface";
> + dmas = <&blsp1_dma 8>, <&blsp1_dma 9>;
> + dma-names = "tx", "rx";
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&spi3_default>;
> + pinctrl-1 = <&spi3_sleep>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + blsp_i2c4: i2c@78b8000 {
> + compatible = "qcom,i2c-qup-v2.2.1";
> + reg = <0x078b8000 0x500>;
> + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>,
> + <&gcc GCC_BLSP1_AHB_CLK>;
> + clock-names = "core", "iface";
> + dmas = <&blsp1_dma 10>, <&blsp1_dma 11>;
> + dma-names = "tx", "rx";
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&i2c4_default>;
> + pinctrl-1 = <&i2c4_sleep>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + blsp_i2c5: i2c@7af5000 {
> + compatible = "qcom,i2c-qup-v2.2.1";
> + reg = <0x07af5000 0x600>;
> + interrupts = <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_BLSP2_QUP1_I2C_APPS_CLK>,
> + <&gcc GCC_BLSP2_AHB_CLK>;
> + clock-names = "core", "iface";
> + dmas = <&blsp2_dma 4>, <&blsp2_dma 5>;
> + dma-names = "tx", "rx";
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&i2c5_default>;
> + pinctrl-1 = <&i2c5_sleep>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + blsp_spi6: spi@7af6000 {
> + compatible = "qcom,spi-qup-v2.2.1";
> + reg = <0x07af6000 0x600>;
> + interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_BLSP2_QUP2_SPI_APPS_CLK>,
> + <&gcc GCC_BLSP2_AHB_CLK>;
> + clock-names = "core", "iface";
> + dmas = <&blsp2_dma 6>, <&blsp2_dma 7>;
> + dma-names = "tx", "rx";
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&spi6_default>;
> + pinctrl-1 = <&spi6_sleep>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + usb_hs_phy: phy@6c000 {
> + compatible = "qcom,usb-hs-28nm-femtophy";
> + reg = <0x6c000 0x200>;
> + #phy-cells = <0>;
> + clocks = <&xo_board>,
> + <&gcc GCC_USB_HS_PHY_CFG_AHB_CLK>,
> + <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
> + clock-names = "ref", "ahb", "sleep";
> + resets = <&gcc GCC_QUSB2_PHY_BCR>,
> + <&gcc GCC_USB2_HS_PHY_ONLY_BCR>;
> + reset-names = "phy", "por";
> + status = "disabled";
> + };
> +
> + usb: usb@78db000 {
> + compatible = "qcom,ci-hdrc";
> + reg = <0x078db000 0x200>,
> + <0x078db200 0x200>;
> + interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_USB_HS_AHB_CLK>,
> + <&gcc GCC_USB_HS_SYSTEM_CLK>;
> + clock-names = "iface", "core";
> + assigned-clocks = <&gcc GCC_USB_HS_SYSTEM_CLK>;
> + assigned-clock-rates = <80000000>;
> + resets = <&gcc GCC_USB_HS_BCR>;
> + reset-names = "core";
> + phy_type = "ulpi";
> + dr_mode = "otg";
> + hnp-disable;
> + srp-disable;
> + adp-disable;
> + ahb-burst-config = <0>;
> + phy-names = "usb-phy";
> + phys = <&usb_hs_phy>;
> + status = "disabled";
> + #reset-cells = <1>;
> + };
> +
> + pronto: wcnss: remoteproc@a21b000 {
One label should be enough.
> + compatible = "qcom,pronto-v3-pil", "qcom,pronto";
> + reg = <0x0a204000 0x2000>, <0x0a202000 0x1000>, <0x0a21b000 0x3000>;
> + reg-names = "ccu", "dxe", "pmu";
> +
> + memory-region = <&wcnss_mem>;
> +
> + interrupts-extended = <&intc GIC_SPI 149 IRQ_TYPE_EDGE_RISING>,
> + <&wcnss_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
> + <&wcnss_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
> + <&wcnss_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
> + <&wcnss_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
> + interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack";
> +
> + power-domains = <&rpmpd MSM8917_VDDCX>,
> + <&rpmpd MSM8917_VDDMX>;
> + power-domain-names = "cx", "mx";
> +
> + qcom,smem-states = <&wcnss_smp2p_out 0>;
> + qcom,smem-state-names = "stop";
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&wcnss_pin_a>;
> +
> + status = "disabled";
> +
> + wcnss_iris: iris {
> + clocks = <&rpmcc RPM_SMD_RF_CLK2>;
> + clock-names = "xo";
> + };
> +
> + smd-edge {
> + interrupts = <GIC_SPI 142 IRQ_TYPE_EDGE_RISING>;
> +
> + qcom,ipc = <&apcs 8 17>;
mboxes
> + qcom,smd-edge = <6>;
> + qcom,remote-pid = <4>;
> +
> + label = "pronto";
> +
> + wcnss_ctrl: wcnss {
> + compatible = "qcom,wcnss";
> + qcom,smd-channels = "WCNSS_CTRL";
> +
> + qcom,mmio = <&pronto>;
> +
> + wcnss_bt: bluetooth {
> + compatible = "qcom,wcnss-bt";
> + };
> +
> + wcnss_wifi: wifi {
> + compatible = "qcom,wcnss-wlan";
> +
> + interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "tx", "rx";
> +
> + qcom,smem-states = <&apps_smsm 10>, <&apps_smsm 9>;
> + qcom,smem-state-names = "tx-enable",
> + "tx-rings-empty";
> + };
> + };
> + };
> + };
> +
> + intc: interrupt-controller@b000000 {
> + compatible = "qcom,msm-qgic2";
> + interrupt-controller;
> + #interrupt-cells = <3>;
> + reg = <0x0b000000 0x1000>,
> + <0x0b002000 0x1000>;
> + };
> +
> + watchdog@b017000 {
> + compatible = "qcom,apss-wdt-qcs404", "qcom,kpss-wdt";
> + reg = <0x0b017000 0x1000>;
> + clocks = <&sleep_clk>;
> + };
> +
> + timer@b120000 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> + compatible = "arm,armv7-timer-mem";
> + reg = <0x0b120000 0x1000>;
> + clock-frequency = <19200000>;
> +
> + frame@b121000 {
> + frame-number = <0>;
> + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
> + reg = <0x0b121000 0x1000>,
> + <0x0b122000 0x1000>;
> + };
> +
> + frame@b123000 {
> + frame-number = <1>;
> + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
> + reg = <0x0b123000 0x1000>;
> + status = "disabled";
> + };
> +
> + frame@b124000 {
> + frame-number = <2>;
> + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
> + reg = <0x0b124000 0x1000>;
> + status = "disabled";
> + };
> +
> + frame@b125000 {
> + frame-number = <3>;
> + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
> + reg = <0x0b125000 0x1000>;
> + status = "disabled";
> + };
> +
> + frame@b126000 {
> + frame-number = <4>;
> + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
> + reg = <0x0b126000 0x1000>;
> + status = "disabled";
> + };
> +
> + frame@b127000 {
> + frame-number = <5>;
> + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
> + reg = <0x0b127000 0x1000>;
> + status = "disabled";
> + };
> +
> + frame@b128000 {
> + frame-number = <6>;
> + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
> + reg = <0x0b128000 0x1000>;
> + status = "disabled";
> + };
> + };
> + };
> +
> + thermal_zones: thermal-zones {
> + aoss-thermal {
> + polling-delay-passive = <250>;
> + polling-delay = <1000>;
> +
> + thermal-sensors = <&tsens 0>;
> +
> + trips {
> + aoss_alert0: trip-point0 {
> + temperature = <85000>;
> + hysteresis = <2000>;
> + type = "hot";
> + };
> + };
> + };
> +
> + mdm-core-thermal {
> + polling-delay-passive = <250>;
> + polling-delay = <1000>;
> +
> + thermal-sensors = <&tsens 1>;
> +
> + trips {
> + mdm_core_alert0: trip-point0 {
> + temperature = <85000>;
> + hysteresis = <2000>;
> + type = "hot";
> + };
> + };
> + };
> +
> + q6-thermal {
> + polling-delay-passive = <250>;
> + polling-delay = <1000>;
> +
> + thermal-sensors = <&tsens 2>;
> +
> + trips {
> + q6_alert0: trip-point0 {
> + temperature = <85000>;
> + hysteresis = <2000>;
> + type = "hot";
> + };
> + };
> + };
> +
> + camera-thermal {
> + polling-delay-passive = <250>;
> + polling-delay = <1000>;
> +
> + thermal-sensors = <&tsens 3>;
> +
> + trips {
> + camera_alert0: trip-point0 {
> + temperature = <85000>;
> + hysteresis = <2000>;
> + type = "hot";
> + };
> + };
> + };
> +
> + cpuss1-thermal {
> + polling-delay-passive = <250>;
> + polling-delay = <1000>;
> +
> + thermal-sensors = <&tsens 4>;
> +
> + trips {
> + cpuss1_alert0: trip-point0 {
> + temperature = <75000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + cpuss1_alert1: trip-point1 {
> + temperature = <85000>;
> + hysteresis = <2000>;
> + type = "hot";
> + };
> +
> + cpuss1_crit: cpuss1-crit {
> + temperature = <100000>;
> + hysteresis = <2000>;
> + type = "critical";
> + };
> + };
> + cooling-maps {
> + map0 {
> + trip = <&cpuss1_alert0>;
> + cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> + };
> + };
> + };
> +
> + cpu0-thermal {
> + polling-delay-passive = <250>;
> + polling-delay = <1000>;
> +
> + thermal-sensors = <&tsens 5>;
> +
> + trips {
> + cpu0_alert0: trip-point0 {
> + temperature = <75000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + cpu0_alert1: trip-point1 {
> + temperature = <85000>;
> + hysteresis = <2000>;
> + type = "hot";
> + };
> +
> + cpu0_crit: cpu-crit {
> + temperature = <100000>;
> + hysteresis = <2000>;
> + type = "critical";
> + };
> + };
> + cooling-maps {
> + map0 {
> + trip = <&cpu0_alert1>;
> + cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> + };
> + };
> + };
> +
> + cpu1-thermal {
> + polling-delay-passive = <250>;
> + polling-delay = <1000>;
> +
> + thermal-sensors = <&tsens 6>;
> +
> + trips {
> + cpu1_alert0: trip-point0 {
> + temperature = <75000>;
> + hysteresis = <2000>;
> + type = "hot";
> + };
> +
> + cpu1_alert1: trip-point1 {
> + temperature = <85000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + cpu1_crit: cpu-crit {
> + temperature = <100000>;
> + hysteresis = <2000>;
> + type = "critical";
> + };
> + };
> + cooling-maps {
> + map0 {
> + trip = <&cpu1_alert1>;
> + cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> + };
> + };
> + };
> +
> + cpu2-thermal {
> + polling-delay-passive = <250>;
> + polling-delay = <1000>;
> +
> + thermal-sensors = <&tsens 7>;
> +
> + trips {
> + cpu2_alert0: trip-point0 {
> + temperature = <75000>;
> + hysteresis = <2000>;
> + type = "hot";
> + };
> +
> + cpu2_alert1: trip-point1 {
> + temperature = <85000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + cpu2_crit: cpu-crit {
> + temperature = <100000>;
> + hysteresis = <2000>;
> + type = "critical";
> + };
> + };
> + cooling-maps {
> + map0 {
> + trip = <&cpu2_alert1>;
> + cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> + };
> + };
> + };
> +
> + cpu3-thermal {
> + polling-delay-passive = <250>;
> + polling-delay = <1000>;
> +
> + thermal-sensors = <&tsens 8>;
> +
> + trips {
> + cpu3_alert0: trip-point0 {
> + temperature = <75000>;
> + hysteresis = <2000>;
> + type = "hot";
> + };
> +
> + cpu3_alert1: trip-point1 {
> + temperature = <85000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + cpu3_crit: cpu-crit {
> + temperature = <100000>;
> + hysteresis = <2000>;
> + type = "critical";
> + };
> + };
> + cooling-maps {
> + map0 {
> + trip = <&cpu3_alert1>;
> + cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> + };
> + };
> + };
> +
> + gpu-thermal {
> + polling-delay-passive = <250>;
> + polling-delay = <1000>;
> +
> + thermal-sensors = <&tsens 9>;
> +
> + trips {
> + gpu_alert: trip-point0 {
> + temperature = <70000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + gpu_crit: gpu-crit {
> + temperature = <90000>;
> + hysteresis = <2000>;
> + type = "critical";
> + };
> + };
> +
> + cooling-maps {
> + map0 {
> + trip = <&gpu_alert>;
> + cooling-device = <&gpu THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> + };
> + };
> + };
> + };
> +};
> +
> +#include "msm8917-pins.dtsi"
> diff --git a/arch/arm64/boot/dts/qcom/pm8916.dtsi b/arch/arm64/boot/dts/qcom/pm8916.dtsi
> index f8e4829ff7f7de1f1f4f5da0f41020875d6c7e17..df0f679250ccb6c49a76288fad12f67b01fa6b61 100644
> --- a/arch/arm64/boot/dts/qcom/pm8916.dtsi
> +++ b/arch/arm64/boot/dts/qcom/pm8916.dtsi
Separate commit, please. Or move this to the board file submission.
> @@ -47,7 +47,7 @@ pon@800 {
> mode-bootloader = <0x2>;
> mode-recovery = <0x1>;
>
> - pwrkey {
> + pm8916_pwrkey: pwrkey {
> compatible = "qcom,pm8941-pwrkey";
> interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
> debounce = <15625>;
> @@ -210,6 +210,10 @@ pm8916_pwm: pwm {
> status = "disabled";
> };
>
> + pm8916_spmi_regulators: regulators {
> + compatible = "qcom,pm8916-regulators";
> + };
> +
> pm8916_vib: vibrator@c000 {
> compatible = "qcom,pm8916-vib";
> reg = <0xc000>;
> @@ -219,6 +223,9 @@ pm8916_vib: vibrator@c000 {
> pm8916_codec: audio-codec@f000 {
> compatible = "qcom,pm8916-wcd-analog-codec";
> reg = <0xf000>;
> + reg-names = "pmic-codec-core";
> + clocks = <&xo_board>;
> + clock-names = "mclk";
Why? Is this compatible with other boards?
> interrupt-parent = <&spmi_bus>;
> interrupts = <0x1 0xf0 0x0 IRQ_TYPE_NONE>,
> <0x1 0xf0 0x1 IRQ_TYPE_NONE>,
>
> --
> 2.47.0
>
--
With best wishes
Dmitry
