On Fri, Oct 18, 2024 at 03:05:52AM +0000, Wei Fang wrote:
> > -----Original Message-----
> > From: Wei Fang
> > Sent: 2024年10月18日 10:04
> > To: Frank Li <frank.li@xxxxxxx>
> > Cc: davem@xxxxxxxxxxxxx; edumazet@xxxxxxxxxx; kuba@xxxxxxxxxx;
> > pabeni@xxxxxxxxxx; robh@xxxxxxxxxx; krzk+dt@xxxxxxxxxx;
> > conor+dt@xxxxxxxxxx; Vladimir Oltean <vladimir.oltean@xxxxxxx>; Claudiu
> > Manoil <claudiu.manoil@xxxxxxx>; Clark Wang <xiaoning.wang@xxxxxxx>;
> > christophe.leroy@xxxxxxxxxx; linux@xxxxxxxxxxxxxxx; bhelgaas@xxxxxxxxxx;
> > horms@xxxxxxxxxx; imx@xxxxxxxxxxxxxxx; netdev@xxxxxxxxxxxxxxx;
> > devicetree@xxxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx;
> > linux-pci@xxxxxxxxxxxxxxx
> > Subject: RE: [PATCH v3 net-next 12/13] net: enetc: add preliminary support for
> > i.MX95 ENETC PF
> >
> > [...]
> > > > @@ -1721,14 +1724,25 @@ void enetc_get_si_caps(struct enetc_si *si)
> > > > struct enetc_hw *hw = &si->hw;
> > > > u32 val;
> > > >
> > > > + if (is_enetc_rev1(si))
> > > > + si->clk_freq = ENETC_CLK;
> > > > + else
> > > > + si->clk_freq = ENETC_CLK_333M;
> > >
> > > can you use clk_gate_rate() to get frequency instead of hardcode here.
> >
> > clk_gate_rate() is not possible to be used here, enetc_get_si_caps() is shared
> > by PF and VFs, but VF does not have DT node. Second, LS1028A and S32
> > platform do not use the clocks property.
It should be set when pf probe.
enetc4_pf_netdev_create()
{
...
priv->ref_clk = devm_clk_get_optional(dev, "ref");
I am sure if it is "ref" clock.
if (ref_clk)
si->clk_freq = clk_get_rate(ref_clk);
else
si->clk_freq = ENETC_CLK; //default one for old LS1028A.
Next time, it may be become 444MHz, 555Mhz...
}
> >
> > > Or you should use standard PCIe version information.
> > >
> >
> > What do you mean standard PCIe version? is_enetc_rev1() gets the revision
> > from struct pci_dev:: revision, my understanding is that this is the revision
> > provided by PCIe.
> >
> > [...]
> > > > +
> > > > @@ -593,6 +620,9 @@ static int enetc_get_rxnfc(struct net_device *ndev,
> > > struct ethtool_rxnfc *rxnfc,
> > > > struct enetc_ndev_priv *priv = netdev_priv(ndev);
> > > > int i, j;
> > > >
> > > > + if (is_enetc_rev4(priv->si))
> > > > + return -EOPNOTSUPP;
> > > > +
> > > > switch (rxnfc->cmd) {
> > > > case ETHTOOL_GRXRINGS:
> > > > rxnfc->data = priv->num_rx_rings;
> > > > @@ -643,6 +673,9 @@ static int enetc_set_rxnfc(struct net_device *ndev,
> > > struct ethtool_rxnfc *rxnfc)
> > > > struct enetc_ndev_priv *priv = netdev_priv(ndev);
> > > > int err;
> > > >
> > > > + if (is_enetc_rev4(priv->si))
> > > > + return -EOPNOTSUPP;
> > > > +
> > > > switch (rxnfc->cmd) {
> > > > case ETHTOOL_SRXCLSRLINS:
> > > > if (rxnfc->fs.location >= priv->si->num_fs_entries) @@ -678,6
> > > > +711,9 @@ static u32 enetc_get_rxfh_key_size(struct net_device *ndev)
> > > > {
> > > > struct enetc_ndev_priv *priv = netdev_priv(ndev);
> > > >
> > > > @@ -843,8 +890,12 @@ static int enetc_set_coalesce(struct net_device
> > > > *ndev, static int enetc_get_ts_info(struct net_device *ndev,
> > > > struct kernel_ethtool_ts_info *info) {
> > > > + struct enetc_ndev_priv *priv = netdev_priv(ndev);
> > > > int *phc_idx;
> > > >
> > > > + if (is_enetc_rev4(priv->si))
> > > > + return -EOPNOTSUPP;
> > > > +
> > >
> > > Can you just not set enetc_pf_ethtool_ops if it is imx95 instead of check each
> > > ethtools function? or use difference enetc_pf_ethtool_ops for imx95?
> > >
> >
> > For the first question, in the current patch, i.MX95 already supports some
> > ethtool interfaces, so there is no need to remove them.
> >
> > For the second question, for LS1028A and i.MX95, the logic of these ethtool
> > interfaces is basically the same, the difference is the hardware operation part.
> > It's just that support for i.MX95 has not yet been added. Both the current
> > approach and the approach you suggested will eventually merge into using the
> > same enetc_pf_ethtool_ops, so I don't think there is much practical point in
> > switching to the approach you mentioned.
>
> I thought about it again, your suggestion is more reasonable and easier to
> understand. I will merge the two enetc_pf_ethtool_ops into one after I
> complete the support of all ethtool interfaces of i.MX95. Thanks.
