This series previously only concerned sc8280xp but while enabling WLAN/BT on sm8450 I noticed some more changes will be required so I folded the latter into this series and updated the sc8280xp CRD and X13 patches. == This models the WLAN and Bluetooth modules on several boards using the WCN6855 module. The wcn6855 (also known as qca6490) is a bit different from the qca6390 so modify the power sequencing driver to support it with separate device match data. For the sc8280xp-crd and sm8450-hdk we add the PMU, wifi and bluetooth nodes with the correctly modelled wiring between them. For the X13s, we rework existing nodes so that they align with the new DT bindings contract. On sm8450-hdk we require some additional toggling of the XO-CLK signal so add that to the driver as well and update the bindings. Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@xxxxxxxxxx> --- Changes in v6: - add the xo-clk signal handling to the pwrseq-qcom-wcn driver - add a patch enabling wifi and bluetooth on sm8450-hdk - add missing supplies to the PMUs on sc8280xp boards - Link to v5: https://lore.kernel.org/all/20241008102545.40003-1-brgl@xxxxxxxx/ Changes in v5: - put vreg_s10b under the "B" PMIC on the CRD instead of modeling it as a fixed regulator - order pinctrl nodes alphabetically - restore the drive-strength property for all pins to what bootfw sets it to - disable bias on wlan-en pin on the CRD - remove stray newline - add the swctrl pins to the PMU node Changes in v4: - bind bluetooth pins on X13s in patch 3/3 - only drop the regulator-always-on properties for vreg_s11b and vreg_s12b and fold this change into patch 3/3 Changes in v3: - move adding the bt-enable-gpios to the PMU on the CRD to patch 2/4 - add a patch removing the regulator-always-on property from regulators on X13s that no longer need it Changes in v2: - fix commit message in patch 1/3 - drop drive-strength from the wlan enable pin function - drop the calibration variant property from the wifi node of the CRD --- Bartosz Golaszewski (6): regulator: dt-bindings: qcom,qca6390-pmu: add more properties for wcn6855 power: sequencing: qcom-wcn: improve support for wcn6855 arm64: dts: qcom: sc8280xp-crd: model the PMU of the on-board wcn6855 arm64: dts: qcom: sc8280xp-crd: enable bluetooth arm64: dts: qcom: sc8280xp-x13s: model the PMU of the on-board wcn6855 arm64: dts: qcom: sm8450-hdk: model the PMU of the on-board wcn6855 .../bindings/regulator/qcom,qca6390-pmu.yaml | 12 ++ arch/arm64/boot/dts/qcom/sc8280xp-crd.dts | 169 +++++++++++++++++++++ .../dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts | 103 +++++++++++-- arch/arm64/boot/dts/qcom/sm8450-hdk.dts | 157 +++++++++++++++++++ arch/arm64/boot/dts/qcom/sm8450.dtsi | 2 +- drivers/power/sequencing/pwrseq-qcom-wcn.c | 101 +++++++++++- 6 files changed, 526 insertions(+), 18 deletions(-) --- base-commit: f2493655d2d3d5c6958ed996b043c821c23ae8d3 change-id: 20240807-sc8280xp-pwrseq-7b6859d846c5 Best regards, -- Bartosz Golaszewski <bartosz.golaszewski@xxxxxxxxxx>
