Re: [PATCH v6 2/2] pwm: Add Loongson PWM controller support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Sean:

Thanks for your comment.

On Mon, Oct 14, 2024 at 7:32 PM Sean Young <sean@xxxxxxxx> wrote:
>
> On Thu, Oct 10, 2024 at 04:30:26PM +0800, Binbin Zhou wrote:
> > This commit adds a generic PWM framework driver for the PWM controller
> > found on Loongson family chips.
> >
> > Co-developed-by: Juxin Gao <gaojuxin@xxxxxxxxxxx>
> > Signed-off-by: Juxin Gao <gaojuxin@xxxxxxxxxxx>
> > Signed-off-by: Binbin Zhou <zhoubinbin@xxxxxxxxxxx>
> > Acked-by: Huacai Chen <chenhuacai@xxxxxxxxxxx>
> > ---
> >  MAINTAINERS                |   1 +
> >  drivers/pwm/Kconfig        |  12 ++
> >  drivers/pwm/Makefile       |   1 +
> >  drivers/pwm/pwm-loongson.c | 287 +++++++++++++++++++++++++++++++++++++
> >  4 files changed, 301 insertions(+)
> >  create mode 100644 drivers/pwm/pwm-loongson.c
> >
> > diff --git a/MAINTAINERS b/MAINTAINERS
> > index 18d2c65c744f..9d033799c6ec 100644
> > --- a/MAINTAINERS
> > +++ b/MAINTAINERS
> > @@ -13388,6 +13388,7 @@ M:    Binbin Zhou <zhoubinbin@xxxxxxxxxxx>
> >  L:   linux-pwm@xxxxxxxxxxxxxxx
> >  S:   Maintained
> >  F:   Documentation/devicetree/bindings/pwm/loongson,ls7a-pwm.yaml
> > +F:   drivers/pwm/pwm-loongson.c
> >
> >  LOONGSON-2 SOC SERIES CLOCK DRIVER
> >  M:   Yinbo Zhu <zhuyinbo@xxxxxxxxxxx>
> > diff --git a/drivers/pwm/Kconfig b/drivers/pwm/Kconfig
> > index 0915c1e7df16..ef02a44d83a7 100644
> > --- a/drivers/pwm/Kconfig
> > +++ b/drivers/pwm/Kconfig
> > @@ -351,6 +351,18 @@ config PWM_KEEMBAY
> >         To compile this driver as a module, choose M here: the module
> >         will be called pwm-keembay.
> >
> > +config PWM_LOONGSON
> > +     tristate "Loongson PWM support"
> > +     depends on MACH_LOONGSON64 || COMPILE_TEST
> > +     depends on COMMON_CLK
> > +     help
> > +       Generic PWM framework driver for Loongson family.
> > +       It can be found on Loongson-2K series cpus and Loongson LS7A
> > +       bridge chips.
> > +
> > +       To compile this driver as a module, choose M here: the module
> > +       will be called pwm-loongson.
> > +
> >  config PWM_LP3943
> >       tristate "TI/National Semiconductor LP3943 PWM support"
> >       depends on MFD_LP3943
> > diff --git a/drivers/pwm/Makefile b/drivers/pwm/Makefile
> > index 9081e0c0e9e0..7c18c9be419f 100644
> > --- a/drivers/pwm/Makefile
> > +++ b/drivers/pwm/Makefile
> > @@ -30,6 +30,7 @@ obj-$(CONFIG_PWM_INTEL_LGM) += pwm-intel-lgm.o
> >  obj-$(CONFIG_PWM_IQS620A)    += pwm-iqs620a.o
> >  obj-$(CONFIG_PWM_JZ4740)     += pwm-jz4740.o
> >  obj-$(CONFIG_PWM_KEEMBAY)    += pwm-keembay.o
> > +obj-$(CONFIG_PWM_LOONGSON)   += pwm-loongson.o
> >  obj-$(CONFIG_PWM_LP3943)     += pwm-lp3943.o
> >  obj-$(CONFIG_PWM_LPC18XX_SCT)        += pwm-lpc18xx-sct.o
> >  obj-$(CONFIG_PWM_LPC32XX)    += pwm-lpc32xx.o
> > diff --git a/drivers/pwm/pwm-loongson.c b/drivers/pwm/pwm-loongson.c
> > new file mode 100644
> > index 000000000000..cdd320ed3060
> > --- /dev/null
> > +++ b/drivers/pwm/pwm-loongson.c
> > @@ -0,0 +1,287 @@
> > +// SPDX-License-Identifier: GPL-2.0-only
> > +/*
> > + * Copyright (C) 2017-2024 Loongson Technology Corporation Limited.
> > + *
> > + * Loongson PWM driver
> > + *
> > + * For Loongson's PWM IP block documentation please refer Chapter 11 of
> > + * Reference Manual: https://loongson.github.io/LoongArch-Documentation/Loongson-7A1000-usermanual-EN.pdf
> > + *
> > + * Author: Juxin Gao <gaojuxin@xxxxxxxxxxx>
> > + * Further cleanup and restructuring by:
> > + *         Binbin Zhou <zhoubinbin@xxxxxxxxxxx>
> > + *
> > + * Limitations:
> > + * - The buffer register value should be written before the CTRL register.
> > + * - When disabled the output is driven to 0 independent of the configured
> > + *   polarity.
> > + */
> > +
> > +#include <linux/acpi.h>
> > +#include <linux/clk.h>
> > +#include <linux/device.h>
> > +#include <linux/init.h>
> > +#include <linux/io.h>
> > +#include <linux/kernel.h>
> > +#include <linux/module.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/pwm.h>
> > +#include <linux/units.h>
> > +
> > +/* Loongson PWM registers */
> > +#define LOONGSON_PWM_REG_DUTY                0x4 /* Low Pulse Buffer Register */
> > +#define LOONGSON_PWM_REG_PERIOD              0x8 /* Pulse Period Buffer Register */
> > +#define LOONGSON_PWM_REG_CTRL                0xc /* Control Register */
> > +
> > +/* Control register bits */
> > +#define LOONGSON_PWM_CTRL_EN         BIT(0)  /* Counter Enable Bit */
> > +#define LOONGSON_PWM_CTRL_OE         BIT(3)  /* Pulse Output Enable Control Bit, Valid Low */
> > +#define LOONGSON_PWM_CTRL_SINGLE     BIT(4)  /* Single Pulse Control Bit */
> > +#define LOONGSON_PWM_CTRL_INTE               BIT(5)  /* Interrupt Enable Bit */
> > +#define LOONGSON_PWM_CTRL_INT                BIT(6)  /* Interrupt Bit */
> > +#define LOONGSON_PWM_CTRL_RST                BIT(7)  /* Counter Reset Bit */
> > +#define LOONGSON_PWM_CTRL_CAPTE              BIT(8)  /* Measurement Pulse Enable Bit */
> > +#define LOONGSON_PWM_CTRL_INVERT     BIT(9)  /* Output flip-flop Enable Bit */
> > +#define LOONGSON_PWM_CTRL_DZONE              BIT(10) /* Anti-dead Zone Enable Bit */
> > +
> > +#define LOONGSON_PWM_FREQ_STD                (50 * HZ_PER_KHZ)
> > +
> > +struct pwm_loongson_suspend_store {
> > +     u32 ctrl;
> > +     u32 duty;
> > +     u32 period;
> > +};
> > +
> > +struct pwm_loongson_ddata {
> > +     struct clk *clk;
> > +     void __iomem *base;
> > +     u64 clk_rate;
> > +     struct pwm_loongson_suspend_store lss;
> > +};
> > +
> > +static inline struct pwm_loongson_ddata *to_pwm_loongson_ddata(struct pwm_chip *chip)
> > +{
> > +     return pwmchip_get_drvdata(chip);
> > +}
> > +
> > +static inline u32 pwm_loongson_readl(struct pwm_loongson_ddata *ddata, u32 offset)
> > +{
> > +     return readl(ddata->base + offset);
> > +}
> > +
> > +static inline void pwm_loongson_writel(struct pwm_loongson_ddata *ddata,
> > +                                    u32 val, u32 offset)
> > +{
> > +     writel(val, ddata->base + offset);
> > +}
> > +
> > +static int pwm_loongson_set_polarity(struct pwm_chip *chip, struct pwm_device *pwm,
> > +                                  enum pwm_polarity polarity)
> > +{
> > +     u16 val;
> > +     struct pwm_loongson_ddata *ddata = to_pwm_loongson_ddata(chip);
> > +
> > +     val = pwm_loongson_readl(ddata, LOONGSON_PWM_REG_CTRL);
> > +
> > +     if (polarity == PWM_POLARITY_INVERSED)
> > +             /* Duty cycle defines LOW period of PWM */
> > +             val |= LOONGSON_PWM_CTRL_INVERT;
> > +     else
> > +             /* Duty cycle defines HIGH period of PWM */
> > +             val &= ~LOONGSON_PWM_CTRL_INVERT;
> > +
> > +     pwm_loongson_writel(ddata, val, LOONGSON_PWM_REG_CTRL);
> > +
> > +     return 0;
> > +}
> > +
> > +static void pwm_loongson_disable(struct pwm_chip *chip, struct pwm_device *pwm)
> > +{
> > +     u32 val;
> > +     struct pwm_loongson_ddata *ddata = to_pwm_loongson_ddata(chip);
> > +
> > +     val = pwm_loongson_readl(ddata, LOONGSON_PWM_REG_CTRL);
> > +     val &= ~LOONGSON_PWM_CTRL_EN;
> > +     pwm_loongson_writel(ddata, val, LOONGSON_PWM_REG_CTRL);
> > +}
> > +
> > +static int pwm_loongson_enable(struct pwm_chip *chip, struct pwm_device *pwm)
> > +{
> > +     u32 val;
> > +     struct pwm_loongson_ddata *ddata = to_pwm_loongson_ddata(chip);
> > +
> > +     val = pwm_loongson_readl(ddata, LOONGSON_PWM_REG_CTRL);
> > +     val |= LOONGSON_PWM_CTRL_EN;
> > +     pwm_loongson_writel(ddata, val, LOONGSON_PWM_REG_CTRL);
> > +
> > +     return 0;
> > +}
> > +
> > +static int pwm_loongson_config(struct pwm_chip *chip, struct pwm_device *pwm,
> > +                            u64 duty_ns, u64 period_ns)
> > +{
> > +     u32 duty, period;
> > +     struct pwm_loongson_ddata *ddata = to_pwm_loongson_ddata(chip);
> > +
> > +     /* duty = duty_ns * ddata->clk_rate / NSEC_PER_SEC */
> > +     duty = mul_u64_u64_div_u64(duty_ns, ddata->clk_rate, NSEC_PER_SEC);
> > +     pwm_loongson_writel(ddata, duty, LOONGSON_PWM_REG_DUTY);
> > +
> > +     /* period = period_ns * ddata->clk_rate / NSEC_PER_SEC */
> > +     period = mul_u64_u64_div_u64(period_ns, ddata->clk_rate, NSEC_PER_SEC);
> > +     pwm_loongson_writel(ddata, period, LOONGSON_PWM_REG_PERIOD);
> > +
> > +     return 0;
> > +}
> > +
> > +static int pwm_loongson_apply(struct pwm_chip *chip, struct pwm_device *pwm,
> > +                           const struct pwm_state *state)
> > +{
> > +     int ret;
> > +     u64 period, duty_cycle;
> > +     bool enabled = pwm->state.enabled;
> > +
> > +     if (!state->enabled) {
> > +             if (enabled)
> > +                     pwm_loongson_disable(chip, pwm);
> > +             return 0;
> > +     }
> > +
> > +     ret = pwm_loongson_set_polarity(chip, pwm, state->polarity);
> > +     if (ret)
> > +             return ret;
> > +
> > +     period = min(state->period, NANOHZ_PER_HZ);
> > +     duty_cycle = min(state->duty_cycle, NANOHZ_PER_HZ);
> > +
> > +     ret = pwm_loongson_config(chip, pwm, duty_cycle, period);
> > +     if (ret)
> > +             return ret;
> > +
> > +     if (!enabled && state->enabled)
> > +             ret = pwm_loongson_enable(chip, pwm);
> > +
> > +     return ret;
> > +}
> > +
> > +static int pwm_loongson_get_state(struct pwm_chip *chip, struct pwm_device *pwm,
> > +                               struct pwm_state *state)
> > +{
> > +     u32 duty, period, ctrl;
> > +     struct pwm_loongson_ddata *ddata = to_pwm_loongson_ddata(chip);
> > +
> > +     duty = pwm_loongson_readl(ddata, LOONGSON_PWM_REG_DUTY);
> > +     period = pwm_loongson_readl(ddata, LOONGSON_PWM_REG_PERIOD);
> > +     ctrl = pwm_loongson_readl(ddata, LOONGSON_PWM_REG_CTRL);
> > +
> > +     /* duty & period have a max of 2^32, so we can't overflow */
> > +     state->duty_cycle = DIV64_U64_ROUND_UP((u64)duty * NSEC_PER_SEC, ddata->clk_rate);
> > +     state->period = DIV64_U64_ROUND_UP((u64)period * NSEC_PER_SEC, ddata->clk_rate);
> > +     state->polarity = (ctrl & LOONGSON_PWM_CTRL_INVERT) ? PWM_POLARITY_INVERSED :
> > +                       PWM_POLARITY_NORMAL;
> > +     state->enabled = (ctrl & LOONGSON_PWM_CTRL_EN) ? true : false;
> > +
> > +     return 0;
> > +}
> > +
> > +static const struct pwm_ops pwm_loongson_ops = {
> > +     .apply = pwm_loongson_apply,
> > +     .get_state = pwm_loongson_get_state,
> > +};
> > +
> > +static int pwm_loongson_probe(struct platform_device *pdev)
> > +{
> > +     int ret;
> > +     struct pwm_chip *chip;
> > +     struct pwm_loongson_ddata *ddata;
> > +     struct device *dev = &pdev->dev;
> > +
> > +     chip = devm_pwmchip_alloc(dev, 1, sizeof(*ddata));
> > +     if (IS_ERR(chip))
> > +             return PTR_ERR(chip);
> > +     ddata = to_pwm_loongson_ddata(chip);
> > +
> > +     ddata->base = devm_platform_ioremap_resource(pdev, 0);
> > +     if (IS_ERR(ddata->base))
> > +             return PTR_ERR(ddata->base);
> > +
> > +     if (!has_acpi_companion(dev)) {
> > +             ddata->clk = devm_clk_get_enabled(dev, NULL);
> > +             if (IS_ERR(ddata->clk))
> > +                     return dev_err_probe(dev, PTR_ERR(ddata->clk),
> > +                                          "failed to get pwm clock\n");
> > +             ddata->clk_rate = clk_get_rate(ddata->clk);
> > +     } else {
> > +             ddata->clk_rate = LOONGSON_PWM_FREQ_STD;
> > +     }
> > +
> > +     chip->ops = &pwm_loongson_ops;
>
> I think you can add here:
>
>         chip->atomic = true;
>
> As far as I can see, the driver does not do any sleeping operations
> in pwm_loongson_apply(). This probably should be tested with
> CONFIG_PWM_DEBUG and CONFIG_DEBUG_ATOMIC_SLEEP just to be sure.

I'm a bit confused.

With CONFIG_PWM_DEBUG and CONFIG_DEBUG_ATOMIC_SLEEP, I did some
suspend/resume tests, but there is no relevant error output, including
something like "BUG: sleeping function called from invalid context...
".

Does chip->atomic still need to be set?

Thanks.
Binbin
>
> Thanks,
> Sean
>
>
> > +     dev_set_drvdata(dev, chip);
> > +
> > +     ret = devm_pwmchip_add(dev, chip);
> > +     if (ret < 0)
> > +             return dev_err_probe(dev, ret, "failed to add PWM chip\n");
> > +
> > +     return 0;
> > +}
> > +
> > +static int pwm_loongson_suspend(struct device *dev)
> > +{
> > +     struct pwm_chip *chip = dev_get_drvdata(dev);
> > +     struct pwm_loongson_ddata *ddata = to_pwm_loongson_ddata(chip);
> > +
> > +     ddata->lss.ctrl = pwm_loongson_readl(ddata, LOONGSON_PWM_REG_CTRL);
> > +     ddata->lss.duty = pwm_loongson_readl(ddata, LOONGSON_PWM_REG_DUTY);
> > +     ddata->lss.period = pwm_loongson_readl(ddata, LOONGSON_PWM_REG_PERIOD);
> > +
> > +     clk_disable_unprepare(ddata->clk);
> > +
> > +     return 0;
> > +}
> > +
> > +static int pwm_loongson_resume(struct device *dev)
> > +{
> > +     int ret;
> > +     struct pwm_chip *chip = dev_get_drvdata(dev);
> > +     struct pwm_loongson_ddata *ddata = to_pwm_loongson_ddata(chip);
> > +
> > +     ret = clk_prepare_enable(ddata->clk);
> > +     if (ret)
> > +             return ret;
> > +
> > +     pwm_loongson_writel(ddata, ddata->lss.ctrl, LOONGSON_PWM_REG_CTRL);
> > +     pwm_loongson_writel(ddata, ddata->lss.duty, LOONGSON_PWM_REG_DUTY);
> > +     pwm_loongson_writel(ddata, ddata->lss.period, LOONGSON_PWM_REG_PERIOD);
> > +
> > +     return 0;
> > +}
> > +
> > +static DEFINE_SIMPLE_DEV_PM_OPS(pwm_loongson_pm_ops, pwm_loongson_suspend,
> > +                             pwm_loongson_resume);
> > +
> > +static const struct of_device_id pwm_loongson_of_ids[] = {
> > +     { .compatible = "loongson,ls7a-pwm" },
> > +     { /* sentinel */ },
> > +};
> > +MODULE_DEVICE_TABLE(of, pwm_loongson_of_ids);
> > +
> > +static const struct acpi_device_id pwm_loongson_acpi_ids[] = {
> > +     { "LOON0006" },
> > +     { }
> > +};
> > +MODULE_DEVICE_TABLE(acpi, pwm_loongson_acpi_ids);
> > +
> > +static struct platform_driver pwm_loongson_driver = {
> > +     .probe = pwm_loongson_probe,
> > +     .driver = {
> > +             .name = "loongson-pwm",
> > +             .pm = pm_ptr(&pwm_loongson_pm_ops),
> > +             .of_match_table = pwm_loongson_of_ids,
> > +             .acpi_match_table = pwm_loongson_acpi_ids,
> > +     },
> > +};
> > +module_platform_driver(pwm_loongson_driver);
> > +
> > +MODULE_DESCRIPTION("Loongson PWM driver");
> > +MODULE_AUTHOR("Loongson Technology Corporation Limited.");
> > +MODULE_LICENSE("GPL");
> > --
> > 2.43.5
> >





[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux