On Fri, 20 Feb 2015, Chen-Yu Tsai wrote:
> From: Carlo Caione <carlo@xxxxxxxxxx>
>
> Bindings documentation for the AXP20x driver. In this file also
> sub-nodes are documented.
>
> Signed-off-by: Carlo Caione <carlo@xxxxxxxxxx>
> [wens@xxxxxxxx: clarify interrupt source for the axp PMIC]
> [wens@xxxxxxxx: explain dcdc-workmode in detail and trim lines to 80 chars]
> [wens@xxxxxxxx: make regulator supplies optional if using unregulated input]
> [wens@xxxxxxxx: use cubieboard2 regulator nodes as example]
> [wens@xxxxxxxx: x-powers,dcdc-workmode default changed to 'current hardware
> setting']
> [wens@xxxxxxxx: reorganized regulator related properties into separate
> section.]
> Signed-off-by: Chen-Yu Tsai <wens@xxxxxxxx>
> ---
> Documentation/devicetree/bindings/mfd/axp20x.txt | 96 ++++++++++++++++++++++++
> 1 file changed, 96 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/mfd/axp20x.txt
Applied, thanks.
> diff --git a/Documentation/devicetree/bindings/mfd/axp20x.txt b/Documentation/devicetree/bindings/mfd/axp20x.txt
> new file mode 100644
> index 000000000000..98685f291a72
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/axp20x.txt
> @@ -0,0 +1,96 @@
> +AXP202/AXP209 device tree bindings
> +
> +The axp20x family current members :
> +axp202 (X-Powers)
> +axp209 (X-Powers)
> +
> +Required properties:
> +- compatible: "x-powers,axp202" or "x-powers,axp209"
> +- reg: The I2C slave address for the AXP chip
> +- interrupt-parent: The parent interrupt controller
> +- interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin
> +- interrupt-controller: axp20x has its own internal IRQs
> +- #interrupt-cells: Should be set to 1
> +
> +Optional properties:
> +- x-powers,dcdc-freq: defines the work frequency of DC-DC in KHz
> + (range: 750-1875). Default: 1.5MHz
> +- <input>-supply: a phandle to the regulator supply node. May be omitted if
> + inputs are unregulated, such as using the IPSOUT output
> + from the PMIC.
> +
> +- regulators: A node that houses a sub-node for each regulator. Regulators
> + not used but preferred to be managed by the OS should be
> + listed as well.
> + See Documentation/devicetree/bindings/regulator/regulator.txt
> + for more information on standard regulator bindings.
> +
> +Optional properties for DCDC regulators:
> +- x-powers,dcdc-workmode: 1 for PWM mode, 0 for AUTO (PWM/PFM) mode
> + Default: Current hardware setting
> + The DCDC regulators work in a mixed PWM/PFM mode,
> + using PFM under light loads and switching to PWM
> + for heavier loads. Forcing PWM mode trades efficiency
> + under light loads for lower output noise. This
> + probably makes sense for HiFi audio related
> + applications that aren't battery constrained.
> +
> +
> +AXP202/AXP209 regulators, type, and corresponding input supply names:
> +
> +Regulator Type Supply Name Notes
> +--------- ---- ----------- -----
> +DCDC2 : DC-DC buck : vin2-supply
> +DCDC3 : DC-DC buck : vin3-supply
> +LDO1 : LDO : acin-supply : always on
> +LDO2 : LDO : ldo24in-supply : shared supply
> +LDO3 : LDO : ldo3in-supply
> +LDO4 : LDO : ldo24in-supply : shared supply
> +LDO5 : LDO : ldo5in-supply
> +
> +Example:
> +
> +axp209: pmic@34 {
> + compatible = "x-powers,axp209";
> + reg = <0x34>;
> + interrupt-parent = <&nmi_intc>;
> + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> + interrupt-controller;
> + #interrupt-cells = <1>;
> +
> + regulators {
> + x-powers,dcdc-freq = <1500>;
> +
> + vdd_cpu: dcdc2 {
> + regulator-always-on;
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1450000>;
> + regulator-name = "vdd-cpu";
> + };
> +
> + vdd_int_dll: dcdc3 {
> + regulator-always-on;
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1400000>;
> + regulator-name = "vdd-int-dll";
> + };
> +
> + vdd_rtc: ldo1 {
> + regulator-always-on;
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1400000>;
> + regulator-name = "vdd-rtc";
> + };
> +
> + avcc: ldo2 {
> + regulator-always-on;
> + regulator-min-microvolt = <2700000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "avcc";
> + };
> +
> + ldo3 {
> + /* unused but preferred to be managed by OS */
> + };
> + };
> +};
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
