Despite supporting Auto MDI-X, it looks like Aquantia only supports
swapping pair (1,2) with pair (3,6) like it used to be for MDI-X on
100MBit/s networks.
When all 4 pairs are in use (for 1000MBit/s or faster) the link does not
come up with pair order is not configured correctly, either using
MDI_CFG pin or using the "PMA Receive Reserved Vendor Provisioning 1"
register.
Normally, the order of MDI pairs being either ABCD or DCBA is configured
by pulling the MDI_CFG pin.
However, some hardware designs require overriding the value configured
by that bootstrap pin. The PHY allows doing that by setting a bit in
"PMA Receive Reserved Vendor Provisioning 1" register which allows
ignoring the state of the MDI_CFG pin and another bit configuring
whether the order of MDI pairs should be normal (ABCD) or reverse
(DCBA). Pair polarity is not affected and remains identical in both
settings.
Introduce property "marvell,mdi-cfg-order" which allows forcing either
normal or reverse order of the MDI pairs from DT.
If the property isn't present, the behavior is unchanged and MDI pair
order configuration is untouched (ie. either the result of MDI_CFG pin
pull-up/pull-down, or pair order override already configured by the
bootloader before Linux is started).
Forcing normal pair order is required on the Adtran SDG-8733A Wi-Fi 7
residential gateway.
Signed-off-by: Daniel Golle <daniel@xxxxxxxxxxxxxx>
---
v3: use u32 'marvell,mdi-cfg-order' instead of two mutually exclusive
properties as suggested
v2: add missing 'static' keyword, improve commit description
drivers/net/phy/aquantia/aquantia_main.c | 33 ++++++++++++++++++++++++
1 file changed, 33 insertions(+)
diff --git a/drivers/net/phy/aquantia/aquantia_main.c
b/drivers/net/phy/aquantia/aquantia_main.c
index 4d156d406bab..dcad3fa1ddc3 100644
--- a/drivers/net/phy/aquantia/aquantia_main.c
+++ b/drivers/net/phy/aquantia/aquantia_main.c
@@ -11,6 +11,7 @@
#include <linux/module.h>
#include <linux/delay.h>
#include <linux/bitfield.h>
+#include <linux/of.h>
#include <linux/phy.h>
#include "aquantia.h"
@@ -71,6 +72,11 @@
#define MDIO_AN_TX_VEND_INT_MASK2 0xd401
#define MDIO_AN_TX_VEND_INT_MASK2_LINK BIT(0)
+#define PMAPMD_RSVD_VEND_PROV 0xe400
+#define PMAPMD_RSVD_VEND_PROV_MDI_CONF GENMASK(1, 0)
+#define PMAPMD_RSVD_VEND_PROV_MDI_REVERSE BIT(0)
+#define PMAPMD_RSVD_VEND_PROV_MDI_FORCE BIT(1)
+
#define MDIO_AN_RX_LP_STAT1 0xe820
#define MDIO_AN_RX_LP_STAT1_1000BASET_FULL BIT(15)
#define MDIO_AN_RX_LP_STAT1_1000BASET_HALF BIT(14)
@@ -485,6 +491,29 @@ static void aqr107_chip_info(struct phy_device
*phydev)
fw_major, fw_minor, build_id, prov_id);
}
+static int aqr107_config_mdi(struct phy_device *phydev)
+{
+ struct device_node *np = phydev->mdio.dev.of_node;
+ u32 mdi_conf;
+ int ret;
+
+ ret = of_property_read_u32(np, "marvell,mdi-cfg-order", &mdi_conf);
+
+ /* Do nothing in case property "marvell,mdi-cfg-order" is not
present */
+ if (ret == -ENOENT)
+ return 0;
