Hi Maxime,
On 03/12/2015 05:55 PM, Maxime Coquelin wrote:
> From: Maxime Coquelin <mcoquelin.stm32@xxxxxxxxx>
>
> This drivers adds support to the STM32 USART controller, which is a
> standard serial driver.
Comments below.
> Signed-off-by: Maxime Coquelin <mcoquelin.stm32@xxxxxxxxx>
> ---
> drivers/tty/serial/Kconfig | 17 +
> drivers/tty/serial/Makefile | 1 +
> drivers/tty/serial/stm32-usart.c | 695 +++++++++++++++++++++++++++++++++++++++
> include/uapi/linux/serial_core.h | 3 +
> 4 files changed, 716 insertions(+)
> create mode 100644 drivers/tty/serial/stm32-usart.c
>
> diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
> index d2501f0..880cb4f 100644
> --- a/drivers/tty/serial/Kconfig
> +++ b/drivers/tty/serial/Kconfig
> @@ -1611,6 +1611,23 @@ config SERIAL_SPRD_CONSOLE
> with "earlycon" on the kernel command line. The console is
> enabled when early_param is processed.
>
> +config SERIAL_STM32
> + tristate "STMicroelectronics STM32 serial port support"
> + select SERIAL_CORE
> + depends on ARM || COMPILE_TEST
> + help
> + This driver is for the on-chip Serial Controller on
> + STMicroelectronics STM32 MCUs.
> + USART supports Rx & Tx functionality.
> + It support all industry standard baud rates.
> +
> + If unsure, say N.
> +
> +config SERIAL_STM32_CONSOLE
> + bool "Support for console on STM32"
> + depends on SERIAL_STM32=y
> + select SERIAL_CORE_CONSOLE
> +
> endmenu
>
> config SERIAL_MCTRL_GPIO
> diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile
> index 599be4b..67c5023 100644
> --- a/drivers/tty/serial/Makefile
> +++ b/drivers/tty/serial/Makefile
> @@ -95,6 +95,7 @@ obj-$(CONFIG_SERIAL_FSL_LPUART) += fsl_lpuart.o
> obj-$(CONFIG_SERIAL_CONEXANT_DIGICOLOR) += digicolor-usart.o
> obj-$(CONFIG_SERIAL_MEN_Z135) += men_z135_uart.o
> obj-$(CONFIG_SERIAL_SPRD) += sprd_serial.o
> +obj-$(CONFIG_SERIAL_STM32) += stm32-usart.o
>
> # GPIOLIB helpers for modem control lines
> obj-$(CONFIG_SERIAL_MCTRL_GPIO) += serial_mctrl_gpio.o
> diff --git a/drivers/tty/serial/stm32-usart.c b/drivers/tty/serial/stm32-usart.c
> new file mode 100644
> index 0000000..61bb065
> --- /dev/null
> +++ b/drivers/tty/serial/stm32-usart.c
> @@ -0,0 +1,695 @@
> +/*
> + * Copyright (C) Maxime Coquelin 2015
> + * Author: Maxime Coquelin <mcoquelin.stm32@xxxxxxxxx>
> + * License terms: GNU General Public License (GPL), version 2
> + *
> + * Inspired by st-asc.c from STMicroelectronics (c)
> + */
> +
> +#if defined(CONFIG_SERIAL_STM32_USART_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
> +#define SUPPORT_SYSRQ
> +#endif
> +
> +#include <linux/module.h>
> +#include <linux/serial.h>
> +#include <linux/console.h>
> +#include <linux/sysrq.h>
> +#include <linux/platform_device.h>
> +#include <linux/io.h>
> +#include <linux/irq.h>
> +#include <linux/tty.h>
> +#include <linux/tty_flip.h>
> +#include <linux/delay.h>
> +#include <linux/spinlock.h>
> +#include <linux/pm_runtime.h>
> +#include <linux/of.h>
> +#include <linux/of_platform.h>
> +#include <linux/serial_core.h>
> +#include <linux/clk.h>
> +
> +#define DRIVER_NAME "stm32-usart"
> +
> +/* Register offsets */
> +#define USART_SR 0x00
> +#define USART_DR 0x04
> +#define USART_BRR 0x08
> +#define USART_CR1 0x0c
> +#define USART_CR2 0x10
> +#define USART_CR3 0x14
> +#define USART_GTPR 0x18
> +
> +/* USART_SR */
> +#define USART_SR_PE BIT(0)
> +#define USART_SR_FE BIT(1)
> +#define USART_SR_NF BIT(2)
> +#define USART_SR_ORE BIT(3)
> +#define USART_SR_IDLE BIT(4)
> +#define USART_SR_RXNE BIT(5)
> +#define USART_SR_TC BIT(6)
> +#define USART_SR_TXE BIT(7)
> +#define USART_SR_LBD BIT(8)
> +#define USART_SR_CTS BIT(9)
> +#define USART_SR_ERR_MASK (USART_SR_LBD | USART_SR_ORE | \
> + USART_SR_FE | USART_SR_PE)
> +/* Dummy bits */
> +#define USART_SR_DUMMY_RX BIT(16)
> +
> +/* USART_DR */
> +#define USART_DR_MASK GENMASK(8, 0)
> +
> +/* USART_BRR */
> +#define USART_BRR_DIV_F_MASK GENMASK(3, 0)
> +#define USART_BRR_DIV_M_MASK GENMASK(15, 4)
> +#define USART_BRR_DIV_M_SHIFT 4
> +
> +/* USART_CR1 */
> +#define USART_CR1_SBK BIT(0)
> +#define USART_CR1_RWU BIT(1)
> +#define USART_CR1_RE BIT(2)
> +#define USART_CR1_TE BIT(3)
> +#define USART_CR1_IDLEIE BIT(4)
> +#define USART_CR1_RXNEIE BIT(5)
> +#define USART_CR1_TCIE BIT(6)
> +#define USART_CR1_TXEIE BIT(7)
> +#define USART_CR1_PEIE BIT(8)
> +#define USART_CR1_PS BIT(9)
> +#define USART_CR1_PCE BIT(10)
> +#define USART_CR1_WAKE BIT(11)
> +#define USART_CR1_M BIT(12)
> +#define USART_CR1_UE BIT(13)
> +#define USART_CR1_OVER8 BIT(15)
> +#define USART_CR1_IE_MASK GENMASK(8, 4)
> +
> +/* USART_CR2 */
> +#define USART_CR2_ADD_MASK GENMASK(3, 0)
> +#define USART_CR2_LBDL BIT(5)
> +#define USART_CR2_LBDIE BIT(6)
> +#define USART_CR2_LBCL BIT(8)
> +#define USART_CR2_CPHA BIT(9)
> +#define USART_CR2_CPOL BIT(10)
> +#define USART_CR2_CLKEN BIT(11)
> +#define USART_CR2_STOP_2B BIT(13)
> +#define USART_CR2_STOP_MASK GENMASK(13, 12)
> +#define USART_CR2_LINEN BIT(14)
> +
> +/* USART_CR3 */
> +#define USART_CR3_EIE BIT(0)
> +#define USART_CR3_IREN BIT(1)
> +#define USART_CR3_IRLP BIT(2)
> +#define USART_CR3_HDSEL BIT(3)
> +#define USART_CR3_NACK BIT(4)
> +#define USART_CR3_SCEN BIT(5)
> +#define USART_CR3_DMAR BIT(6)
> +#define USART_CR3_DMAT BIT(7)
> +#define USART_CR3_RTSE BIT(8)
> +#define USART_CR3_CTSE BIT(9)
> +#define USART_CR3_CTSIE BIT(10)
> +#define USART_CR3_ONEBIT BIT(11)
> +
> +/* USART_GTPR */
> +#define USART_GTPR_PSC_MASK GENMASK(7, 0)
> +#define USART_GTPR_GT_MASK GENMASK(15, 8)
> +
> +#define DRIVER_NAME "stm32-usart"
> +#define STM32_SERIAL_NAME "ttyS"
> +#define STM32_MAX_PORTS 6
> +
> +struct stm32_port {
> + struct uart_port port;
> + struct clk *clk;
> +};
> +
> +static struct stm32_port stm32_ports[STM32_MAX_PORTS];
> +static struct uart_driver stm32_usart_driver;
> +
> +static void stm32_stop_tx(struct uart_port *port);
> +
> +static void stm32_set_bits(struct uart_port *port, u32 reg, u32 bits)
> +{
> + u32 val;
> +
> + val = readl_relaxed(port->membase + reg);
> + val |= bits;
> + writel_relaxed(val, port->membase + reg);
> +}
> +
> +static void stm32_clr_bits(struct uart_port *port, u32 reg, u32 bits)
> +{
> + u32 val;
> +
> + val = readl_relaxed(port->membase + reg);
> + val &= ~bits;
> + writel_relaxed(val, port->membase + reg);
> +}
> +
> +static void stm32_receive_chars(struct uart_port *port)
> +{
> + struct tty_port *tport = &port->state->port;
> + unsigned long c;
> + u32 sr;
> + char flag;
> +
> + if (port->irq_wake)
> + pm_wakeup_event(tport->tty->dev, 0);
> +
> + while ((sr = readl_relaxed(port->membase + USART_SR)) & USART_SR_RXNE) {
> + sr |= USART_SR_DUMMY_RX;
> + c = readl_relaxed(port->membase + USART_DR);
> + flag = TTY_NORMAL;
> + port->icount.rx++;
> +
> + if (sr & USART_SR_ERR_MASK) {
> + if (sr & USART_SR_LBD) {
> + port->icount.brk++;
> + if (uart_handle_break(port))
> + continue;
> + } else if (sr & USART_SR_ORE) {
> + port->icount.overrun++;
> + } else if (sr & USART_SR_PE) {
> + port->icount.parity++;
> + } else if (sr & USART_SR_FE) {
> + port->icount.frame++;
> + }
> +
> + sr &= port->read_status_mask;
> +
> + if (sr & USART_SR_LBD)
> + flag = TTY_BREAK;
> + else if (sr & USART_SR_PE)
> + flag = TTY_PARITY;
> + else if (sr & USART_SR_FE)
> + flag = TTY_FRAME;
> + }
> +
> + if (uart_handle_sysrq_char(port, c))
> + continue;
> + uart_insert_char(port, sr, USART_SR_ORE, c, flag);
> + }
> +
> + spin_unlock(&port->lock);
> + tty_flip_buffer_push(tport);
> + spin_lock(&port->lock);
> +}
> +
> +static void stm32_transmit_chars(struct uart_port *port)
> +{
> + struct circ_buf *xmit = &port->state->xmit;
> +
> + if (port->x_char) {
> + writel_relaxed(port->x_char, port->membase + USART_DR);
> + port->x_char = 0;
> + port->icount.tx++;
> + return;
> + }
> +
> + if (uart_tx_stopped(port)) {
> + stm32_stop_tx(port);
> + return;
> + }
> +
> + if (uart_circ_empty(xmit)) {
> + stm32_stop_tx(port);
> + return;
> + }
> +
> + writel_relaxed(xmit->buf[xmit->tail], port->membase + USART_DR);
> + xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
> + port->icount.tx++;
> +
> + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
> + uart_write_wakeup(port);
> +
> + if (uart_circ_empty(xmit))
> + stm32_stop_tx(port);
> +}
> +
> +static irqreturn_t stm32_interrupt(int irq, void *ptr)
> +{
> + struct uart_port *port = ptr;
> + u32 sr;
> +
> + spin_lock(&port->lock);
> +
> + sr = readl_relaxed(port->membase + USART_SR);
> +
> + if (sr & USART_SR_RXNE)
> + stm32_receive_chars(port);
> +
> + if (sr & USART_SR_TXE)
> + stm32_transmit_chars(port);
> +
> + spin_unlock(&port->lock);
> +
> + return IRQ_HANDLED;
> +}
> +
> +static unsigned int stm32_tx_empty(struct uart_port *port)
> +{
> + return readl_relaxed(port->membase + USART_SR) & USART_SR_TXE;
> +}
> +
> +static void stm32_set_mctrl(struct uart_port *port, unsigned int mctrl)
> +{
> + /*
> + * This routine is used for seting signals of: DTR, DCD, CTS/RTS
> + * We use USART's hardware for CTS/RTS, so don't need any for that.
If this means that you're enabling autoflow control, then you still need
to respond to the state of TIOCM_RTS, so that both serial core and userspace
can halt input flow.
If the hardware doesn't support separate RTS enable/disable control,
then you need to disable autoRTS when TIOCM_RTS is clear, and re-enable
it when raised.
> + * Some boards have DTR and DCD implemented using PIO pins,
> + * code to do this should be hooked in here.
> + */
> +}
> +
> +static unsigned int stm32_get_mctrl(struct uart_port *port)
> +{
> + /*
> + * This routine is used for geting signals of: DTR, DCD, DSR, RI,
> + * and CTS/RTS
> + */
> + return TIOCM_CAR | TIOCM_DSR | TIOCM_CTS;
> +}
> +
> +/* There are probably characters waiting to be transmitted. */
> +static void stm32_start_tx(struct uart_port *port)
> +{
> + struct circ_buf *xmit = &port->state->xmit;
> +
> + if (uart_circ_empty(xmit))
> + return;
> +
> + stm32_set_bits(port, USART_CR1, USART_CR1_TXEIE | USART_CR1_TE);
> +}
> +
> +/* Transmit stop */
> +static void stm32_stop_tx(struct uart_port *port)
> +{
> + stm32_clr_bits(port, USART_CR1, USART_CR1_TXEIE);
> +}
> +
> +/* Receive stop */
> +static void stm32_stop_rx(struct uart_port *port)
> +{
> + stm32_clr_bits(port, USART_CR1, USART_CR1_RXNEIE);
> +}
> +
> +/* Handle breaks - ignored by us */
> +static void stm32_break_ctl(struct uart_port *port, int break_state)
> +{
> + /* Nothing here yet .. */
> +}
> +
> +static int stm32_startup(struct uart_port *port)
> +{
> + const char *name = to_platform_device(port->dev)->name;
> + u32 val;
> +
> + if (request_irq(port->irq, stm32_interrupt, IRQF_NO_SUSPEND,
> + name, port)) {
> + dev_err(port->dev, "cannot allocate irq %d\n", port->irq);
> + return -ENODEV;
> + }
> +
> + val = USART_CR1_RXNEIE | USART_CR1_TE | USART_CR1_RE;
> + stm32_set_bits(port, USART_CR1, val);
> +
> + return 0;
> +}
> +
> +static void stm32_shutdown(struct uart_port *port)
> +{
> + u32 val;
> +
> + val = USART_CR1_TXEIE | USART_CR1_RXNEIE | USART_CR1_TE | USART_CR1_RE;
> + stm32_set_bits(port, USART_CR1, val);
> +
> + free_irq(port->irq, port);
> +}
> +
> +static void stm32_set_termios(struct uart_port *port, struct ktermios *termios,
> + struct ktermios *old)
> +{
> + unsigned int baud;
> + u32 usardiv, mantissa, fraction;
> + tcflag_t cflag;
> + u32 cr1, cr2, cr3;
> + unsigned long flags;
> +
> + baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk / 16);
> + cflag = termios->c_cflag;
> +
> + spin_lock_irqsave(&port->lock, flags);
> +
> + /* Stop serial port and reset value */
> + writel_relaxed(0, port->membase + USART_CR1);
> +
> + cr1 = USART_CR1_TE | USART_CR1_RE | USART_CR1_UE | USART_CR1_RXNEIE;
> +
> + if (cflag & CSTOPB)
> + cr2 = USART_CR2_STOP_2B;
> +
> + if (cflag & PARENB) {
> + cr1 |= USART_CR1_PCE;
> + if ((cflag & CSIZE) == CS8)
> + cr1 |= USART_CR1_M;
> + }
> +
> + if (cflag & PARODD)
> + cr1 |= USART_CR1_PS;
> +
> + if (cflag & CRTSCTS)
> + cr3 = USART_CR3_RTSE | USART_CR3_CTSE;
If this means autoflow control, then you need to define
throttle()/unthrottle() methods, otherwise the serial core won't
be able to throttle the remote when input buffers are about
to overflow.
And you should only enable the autoCTS and let the serial
core enable autoRTS through set_mctrl(TIOCM_RTS).
Just let me know if you need more info about how to do this.
> +
> + usardiv = (port->uartclk * 25) / (baud * 4);
> + mantissa = (usardiv / 100) << USART_BRR_DIV_M_SHIFT;
> + fraction = DIV_ROUND_CLOSEST((usardiv % 100) * 16, 100);
> + if (fraction & ~USART_BRR_DIV_F_MASK) {
> + fraction = 0;
> + mantissa += (1 << USART_BRR_DIV_M_SHIFT);
> + }
> +
> + writel_relaxed(mantissa | fraction, port->membase + USART_BRR);
> +
> + uart_update_timeout(port, cflag, baud);
> +
> + port->read_status_mask = USART_SR_ORE;
> + if (termios->c_iflag & INPCK)
> + port->read_status_mask |= USART_SR_PE | USART_SR_FE;
> + if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK))
> + port->read_status_mask |= USART_SR_LBD;
> +
> + /* Characters to ignore */
> + port->ignore_status_mask = 0;
> + if (termios->c_iflag & IGNPAR)
> + port->ignore_status_mask = USART_SR_PE | USART_SR_FE;
> + if (termios->c_iflag & IGNBRK) {
> + port->ignore_status_mask |= USART_SR_LBD;
> + /*
> + * If we're ignoring parity and break indicators,
> + * ignore overruns too (for real raw support).
> + */
> + if (termios->c_iflag & IGNPAR)
> + port->ignore_status_mask |= USART_SR_ORE;
> + }
> +
> + /*
> + * Ignore all characters if CREAD is not set.
> + */
> + if ((termios->c_cflag & CREAD) == 0)
> + port->ignore_status_mask |= USART_SR_DUMMY_RX;
> +
> + writel_relaxed(cr3, port->membase + USART_CR3);
> + writel_relaxed(cr2, port->membase + USART_CR2);
> + writel_relaxed(cr1, port->membase + USART_CR1);
> +
> + spin_unlock_irqrestore(&port->lock, flags);
> +}
> +
> +static const char *stm32_type(struct uart_port *port)
> +{
> + return (port->type == PORT_STM32) ? DRIVER_NAME : NULL;
> +}
> +
> +static void stm32_release_port(struct uart_port *port)
> +{
> +}
> +
> +static int stm32_request_port(struct uart_port *port)
> +{
> + return 0;
> +}
> +
> +static void stm32_config_port(struct uart_port *port, int flags)
> +{
> + if ((flags & UART_CONFIG_TYPE))
Single parens.
> + port->type = PORT_STM32;
> +}
> +
> +static int
> +stm32_verify_port(struct uart_port *port, struct serial_struct *ser)
> +{
> + /* No user changeable parameters */
> + return -EINVAL;
> +}
> +
> +static void stm32_pm(struct uart_port *port, unsigned int state,
> + unsigned int oldstate)
> +{
> + struct stm32_port *stm32port = container_of(port,
> + struct stm32_port, port);
> + unsigned long flags = 0;
> +
> + switch (state) {
> + case UART_PM_STATE_ON:
> + clk_prepare_enable(stm32port->clk);
> + break;
> + case UART_PM_STATE_OFF:
> + spin_lock_irqsave(&port->lock, flags);
> + stm32_clr_bits(port, USART_CR1, USART_CR1_UE);
> + spin_unlock_irqrestore(&port->lock, flags);
> + clk_disable_unprepare(stm32port->clk);
> + break;
> + }
> +}
> +
> +static struct uart_ops stm32_uart_ops = {
> + .tx_empty = stm32_tx_empty,
> + .set_mctrl = stm32_set_mctrl,
> + .get_mctrl = stm32_get_mctrl,
> + .start_tx = stm32_start_tx,
> + .stop_tx = stm32_stop_tx,
> + .stop_rx = stm32_stop_rx,
> + .break_ctl = stm32_break_ctl,
> + .startup = stm32_startup,
> + .shutdown = stm32_shutdown,
> + .set_termios = stm32_set_termios,
> + .type = stm32_type,
> + .release_port = stm32_release_port,
> + .request_port = stm32_request_port,
> + .config_port = stm32_config_port,
> + .verify_port = stm32_verify_port,
> + .pm = stm32_pm,
> +};
> +
> +static int stm32_init_port(struct stm32_port *stm32port,
> + struct platform_device *pdev)
> +{
> + struct uart_port *port = &stm32port->port;
> + struct resource *res;
> +
> + port->iotype = UPIO_MEM;
> + port->flags = UPF_BOOT_AUTOCONF;
> + port->ops = &stm32_uart_ops;
> + port->dev = &pdev->dev;
> + port->irq = platform_get_irq(pdev, 0);
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + port->membase = devm_ioremap_resource(&pdev->dev, res);
> + if (IS_ERR(port->membase))
> + return PTR_ERR(port->membase);
> + port->mapbase = res->start;
> +
> + spin_lock_init(&port->lock);
> +
> + stm32port->clk = devm_clk_get(&pdev->dev, NULL);
> +
> + if (WARN_ON(IS_ERR(stm32port->clk)))
Do you really need a stack trace here? Could this be dev_err() instead?
> + return -EINVAL;
> +
> + /* ensure that clk rate is correct by enabling the clk */
> + clk_prepare_enable(stm32port->clk);
> + stm32port->port.uartclk = clk_get_rate(stm32port->clk);
> + WARN_ON(stm32port->port.uartclk == 0);
Or here?
> + clk_disable_unprepare(stm32port->clk);
> +
> + return 0;
> +}
> +
> +static struct stm32_port *stm32_of_get_stm32_port(struct platform_device *pdev)
> +{
> + struct device_node *np = pdev->dev.of_node;
> + int id;
> +
> + if (!np)
> + return NULL;
> +
> + id = of_alias_get_id(np, STM32_SERIAL_NAME);
> +
> + if (id < 0)
> + id = 0;
> +
> + if (WARN_ON(id >= STM32_MAX_PORTS))
Or here?
> + return NULL;
> +
> + stm32_ports[id].port.line = id;
> + return &stm32_ports[id];
> +}
> +
> +#ifdef CONFIG_OF
> +static const struct of_device_id stm32_match[] = {
> + { .compatible = "st,stm32-usart", },
> + {},
> +};
> +
> +MODULE_DEVICE_TABLE(of, stm32_match);
> +#endif
> +
> +static int stm32_serial_probe(struct platform_device *pdev)
> +{
> + int ret;
> + struct stm32_port *stm32port;
> +
> + stm32port = stm32_of_get_stm32_port(pdev);
> + if (!stm32port)
> + return -ENODEV;
> +
> + ret = stm32_init_port(stm32port, pdev);
> + if (ret)
> + return ret;
> +
> + ret = uart_add_one_port(&stm32_usart_driver, &stm32port->port);
> + if (ret)
> + return ret;
> +
> + platform_set_drvdata(pdev, &stm32port->port);
> +
> + return 0;
> +}
> +
> +static int stm32_serial_remove(struct platform_device *pdev)
> +{
> + struct uart_port *port = platform_get_drvdata(pdev);
> +
> + return uart_remove_one_port(&stm32_usart_driver, port);
> +}
> +
> +
> +#ifdef CONFIG_SERIAL_STM32_CONSOLE
> +static void stm32_console_putchar(struct uart_port *port, int ch)
> +{
> + while (!(readl_relaxed(port->membase + USART_SR) & USART_SR_TXE))
> + cpu_relax();
> +
> + writel_relaxed(ch, port->membase + USART_DR);
> +}
> +
> +static void stm32_console_write(struct console *co, const char *s, unsigned cnt)
> +{
> + struct uart_port *port = &stm32_ports[co->index].port;
> + unsigned long flags;
> + u32 old_cr1, new_cr1;
> + int locked = 1;
> +
> + if (oops_in_progress) {
> + locked = spin_trylock_irqsave(&port->lock, flags);
> + } else {
> + locked = 1;
> + spin_lock_irqsave(&port->lock, flags);
> + }
> +
> + /* Save and disable interrupts */
> + old_cr1 = readl_relaxed(port->membase + USART_CR1);
> + new_cr1 = old_cr1 & ~USART_CR1_IE_MASK;
> + writel_relaxed(new_cr1, port->membase + USART_CR1);
> +
> + uart_console_write(port, s, cnt, stm32_console_putchar);
> +
> + /* Restore interrupt state */
> + writel_relaxed(old_cr1, port->membase + USART_CR1);
> +
> + if (locked)
> + spin_unlock_irqrestore(&port->lock, flags);
> +}
> +
> +static int stm32_console_setup(struct console *co, char *options)
> +{
> + struct stm32_port *stm32port;
> + int baud = 9600;
> + int bits = 8;
> + int parity = 'n';
> + int flow = 'n';
> +
> + if (co->index >= STM32_MAX_PORTS)
> + return -ENODEV;
> +
> + stm32port = &stm32_ports[co->index];
> +
> + /*
> + * This driver does not support early console initialization
> + * (use ARM early printk support instead), so we only expect
> + * this to be called during the uart port registration when the
> + * driver gets probed and the port should be mapped at that point.
> + */
> + if (stm32port->port.mapbase == 0 || stm32port->port.membase == NULL)
> + return -ENXIO;
> +
> + if (options)
> + uart_parse_options(options, &baud, &parity, &bits, &flow);
> +
> + return uart_set_options(&stm32port->port, co, baud, parity, bits, flow);
> +}
> +
> +static struct console stm32_console = {
> + .name = STM32_SERIAL_NAME,
> + .device = uart_console_device,
> + .write = stm32_console_write,
> + .setup = stm32_console_setup,
> + .flags = CON_PRINTBUFFER,
> + .index = -1,
> + .data = &stm32_usart_driver,
> +};
> +
> +#define STM32_SERIAL_CONSOLE (&stm32_console)
> +
> +#else
> +#define STM32_SERIAL_CONSOLE NULL
> +#endif /* CONFIG_SERIAL_STM32_CONSOLE */
> +
> +static struct uart_driver stm32_usart_driver = {
> + .owner = THIS_MODULE,
> + .driver_name = DRIVER_NAME,
> + .dev_name = STM32_SERIAL_NAME,
> + .major = 0,
> + .minor = 0,
> + .nr = STM32_MAX_PORTS,
> + .cons = STM32_SERIAL_CONSOLE,
> +};
> +
> +static struct platform_driver stm32_serial_driver = {
> + .probe = stm32_serial_probe,
> + .remove = stm32_serial_remove,
> + .driver = {
> + .name = DRIVER_NAME,
> + .owner = THIS_MODULE,
> + .of_match_table = of_match_ptr(stm32_match),
> + },
> +};
> +
> +static int __init usart_init(void)
> +{
> + int ret;
> + static char banner[] __initdata =
> + KERN_INFO "STM32 USART driver initialized\n";
> +
> + printk(banner);
> +
> + ret = uart_register_driver(&stm32_usart_driver);
> + if (ret)
> + return ret;
> +
> + ret = platform_driver_register(&stm32_serial_driver);
> + if (ret)
> + uart_unregister_driver(&stm32_usart_driver);
> +
> + return ret;
> +}
> +
> +static void __exit usart_exit(void)
> +{
> + platform_driver_unregister(&stm32_serial_driver);
> + uart_unregister_driver(&stm32_usart_driver);
> +}
> +
> +module_init(usart_init);
> +module_exit(usart_exit);
> +
> +MODULE_ALIAS("platform:" DRIVER_NAME);
> +MODULE_DESCRIPTION("STMicroelectronics STM32 serial port driver");
> +MODULE_LICENSE("GPL");
> diff --git a/include/uapi/linux/serial_core.h b/include/uapi/linux/serial_core.h
> index b212281..e22dee5 100644
> --- a/include/uapi/linux/serial_core.h
> +++ b/include/uapi/linux/serial_core.h
> @@ -258,4 +258,7 @@
> /* Cris v10 / v32 SoC */
> #define PORT_CRIS 112
>
> +/* STM32 USART */
> +#define PORT_STM32 110
Already taken.
You'll want to make sure v4 applies cleanly to Greg's tty-next branch.
Regards,
Peter Hurley
> +
> #endif /* _UAPILINUX_SERIAL_CORE_H */
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
