Hi Stefan,
> Hi Lukasz,
>
> please adjust the subject of your patch accordingly to the subsystem.
>
> Suggestion
>
> ARM: dts: mxs: Add descriptions for imx287 based btt3-[012] devices
>
> Am 12.09.24 um 14:48 schrieb Lukasz Majewski:
> > The btt3 device' HW revisions from 0 to 2 use imx287 SoC and are to
> > some extend similar to already upstreamed XEA devices, hence are
> > using common imx28-lwe.dtsi file.
> >
> > New, imx28-btt3.dtsi has been added to embrace common DTS
> > properties for different HW revisions for this device.
> >
> > As a result - changes introduced in imx28-btt3-[012].dts are
> > minimal.
> >
> > Signed-off-by: Lukasz Majewski <lukma@xxxxxxx>
> >
> > ---
> > Changes for v2:
> > - Rename dts file from btt3-[012] to imx28-btt3-[012] to match
> > current linux kernel naming convention
> > - Remove 'wlf,wm8974' from compatible for codec@1a
> >
> > Changes for v3:
> > - Keep alphabethical order for Makefile entries
> >
> > Changes for v4:
> > - Change compatible for btt3 board (to 'lwn,imx28-btt3')
> >
> > Changes for v5:
> > - Combine patch, which adds btt3-[012] with one adding board entry
> > to fsl.yaml
> >
> > Changes for v6:
> > - Make the patch series for adding entry in fsl.yaml and btt3
> > ---
> > arch/arm/boot/dts/nxp/mxs/Makefile | 3 +
> > arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dts | 12 +
> > arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dts | 8 +
> > arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dts | 12 +
> > arch/arm/boot/dts/nxp/mxs/imx28-btt3.dtsi | 320
> > +++++++++++++++++++++ 5 files changed, 355 insertions(+)
> > create mode 100644 arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dts
> > create mode 100644 arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dts
> > create mode 100644 arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dts
> > create mode 100644 arch/arm/boot/dts/nxp/mxs/imx28-btt3.dtsi
> >
> > diff --git a/arch/arm/boot/dts/nxp/mxs/Makefile
> > b/arch/arm/boot/dts/nxp/mxs/Makefile index
> > a430d04f9c69..96dd31ea19ba 100644 ---
> > a/arch/arm/boot/dts/nxp/mxs/Makefile +++
> > b/arch/arm/boot/dts/nxp/mxs/Makefile @@ -8,6 +8,9 @@
> > dtb-$(CONFIG_ARCH_MXS) += \ imx28-apf28.dtb \
> > imx28-apf28dev.dtb \
> > imx28-apx4devkit.dtb \
> > + imx28-btt3-0.dtb \
> > + imx28-btt3-1.dtb \
> > + imx28-btt3-2.dtb \
> > imx28-cfa10036.dtb \
> > imx28-cfa10037.dtb \
> > imx28-cfa10049.dtb \
> > diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dts
> > b/arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dts new file mode 100644
> > index 000000000000..6ac46e4b21bb
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dts
> > @@ -0,0 +1,12 @@
> > +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> > +/*
> > + * Copyright 2024
> > + * Lukasz Majewski, DENX Software Engineering, lukma@xxxxxxx
> > + */
> > +
> > +/dts-v1/;
> > +#include "imx28-btt3.dtsi"
> > +
> > +&hog_pins_rev {
> > + fsl,pull-up = <MXS_PULL_ENABLE>;
> > +};
> > diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dts
> > b/arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dts new file mode 100644
> > index 000000000000..213fe931c58b
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dts
> > @@ -0,0 +1,8 @@
> > +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> > +/*
> > + * Copyright 2024
> > + * Lukasz Majewski, DENX Software Engineering, lukma@xxxxxxx
> > + */
> > +
> > +/dts-v1/;
> > +#include "imx28-btt3.dtsi"
> > diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dts
> > b/arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dts new file mode 100644
> > index 000000000000..c787c2d03463
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dts
> > @@ -0,0 +1,12 @@
> > +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> > +/*
> > + * Copyright 2024
> > + * Lukasz Majewski, DENX Software Engineering, lukma@xxxxxxx
> > + */
> > +
> > +/dts-v1/;
> > +#include "imx28-btt3.dtsi"
> > +
> > +&lcdif {
> > + display = <&display_te_b>;
> The reason why you don't move the second display into this file is
> because you expect a new hardware revision in the future?
Yes, exactly. This is long-standing device.
> > +};
> > diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-btt3.dtsi
> > b/arch/arm/boot/dts/nxp/mxs/imx28-btt3.dtsi new file mode 100644
> > index 000000000000..94a21ea8d5d2
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/nxp/mxs/imx28-btt3.dtsi
> > @@ -0,0 +1,320 @@
> > +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> > +/*
> > + * Copyright 2024
> > + * Lukasz Majewski, DENX Software Engineering, lukma@xxxxxxx
> > + */
> > +/dts-v1/;
> > +#include "imx28-lwe.dtsi"
> > +
> > +/ {
> > + model = "BTT3";
> > +
> > + compatible = "lwn,imx28-btt3", "fsl,imx28";
> > +
> > + chosen {
> > + bootargs = "root=/dev/mmcblk0p2 rootfstype=ext4 ro
> > rootwait console=ttyAMA0,115200 panic=1 quiet";
> > + };
> It's a little bit unusual to place so many Linux specific stuff into
> the device tree bootargs.
I do keep the bootargs from first version of the device/DTS to avoid
any "unexpected" regressions.
> > +
> > + memory@40000000 {
> > + reg = <0x40000000 0x10000000>;
> > + device_type = "memory";
> > + };
> > +
> > + poweroff {
> > + compatible = "gpio-poweroff";
> > + gpios = <&gpio0 24 0>;
> Please use the GPIO polarity defines.
Ok.
> > + };
> > +
> > + sound {
> > + compatible = "simple-audio-card";
> > + simple-audio-card,name = "BTTC Audio";
> > + simple-audio-card,widgets = "Speaker", "BTTC
> > Speaker";
> > + simple-audio-card,routing = "BTTC Speaker",
> > "SPKOUTN", "BTTC Speaker", "SPKOUTP";
> > + simple-audio-card,dai-link@0 {
> > + format = "left_j";
> > + bitclock-master = <&dai0_master>;
> > + frame-master = <&dai0_master>;
> > + mclk-fs = <256>;
> > + dai0_master: cpu {
> > + sound-dai = <&saif0>;
> > + };
> > + codec {
> > + sound-dai = <&wm89xx>;
> > + clocks = <&saif0>;
> > + };
> > + };
> > + };
> > +
> > + wifi_pwrseq: sdio-pwrseq {
> > + compatible = "mmc-pwrseq-simple";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&wifi_en_pin_bttc>;
> > + reset-gpios = <&gpio0 27 GPIO_ACTIVE_LOW>;
> > + /* W1-163 needs 60us for WL_EN to be low and */
> > + /* 150ms after high before downloading FW is
> > possible */
> > + post-power-on-delay-ms = <200>;
> > + power-off-delay-us = <100>;
> > + };
> > +};
> > +
> > +&auart0 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&auart0_2pins_a>;
> > + status = "okay";
> > +};
> > +
> > +&auart3 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&auart3_pins_a>;
> > + uart-has-rtscts;
> > + status = "okay";
> > +};
> > +
> > +&i2c0 {
> > + wm89xx: codec@1a {
> > + compatible = "wlf,wm8940";
> > + reg = <0x1a>;
> > + #sound-dai-cells = <0>;
> > + };
> > +};
> > +
> > +&lcdif {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&lcdif_24bit_pins_a>, <&lcdif_sync_pins_bttc>,
> > + <&lcdif_reset_pins_bttc>;
> > + lcd-supply = <®_3v3>;
> > + display = <&display0>;
> > + status = "okay";
> > + display0: display0 {
> > + bits-per-pixel = <32>;
> > + bus-width = <24>;
> > + display-timings {
> > + native-mode = <&timing0>;
> > + timing0: timing0 {
> > + clock-frequency = <6500000>;
> > + hactive = <320>;
> > + vactive = <240>;
> > + hfront-porch = <20>;
> > + hback-porch = <38>;
> > + hsync-len = <30>;
> > + vfront-porch = <4>;
> > + vback-porch = <14>;
> > + vsync-len = <4>;
> > + hsync-active = <0>;
> > + vsync-active = <0>;
> > + de-active = <0>;
> > + pixelclk-active = <1>;
> > + };
> > + };
> > + };
> > + display_te_b: display1 {
> > + bits-per-pixel = <32>;
> > + bus-width = <24>;
> > + display-timings {
> > + native-mode = <&timing0>;
> > + timing_te_b: timing0 {
> > + clock-frequency = <6500000>;
> > + hactive = <320>;
> > + vactive = <240>;
> > + hfront-porch = <20>;
> > + hback-porch = <68>;
> > + hsync-len = <30>;
> > + vfront-porch = <4>;
> > + vback-porch = <14>;
> > + vsync-len = <4>;
> > + hsync-active = <0>;
> > + vsync-active = <0>;
> > + de-active = <1>;
> > + pixelclk-active = <1>;
> > + };
> > + };
> > + };
> > +
> > +};
> > +
> > +&mac0 {
> > + clocks = <&clks 57>, <&clks 57>, <&clks 64>;
> > + clock-names = "ipg", "ahb", "enet_out";
> > + phy-handle = <&mac0_phy>;
> > + phy-mode = "rmii";
> > + phy-supply = <®_3v3>;
> > + local-mac-address = [ 00 11 B8 00 BF 8A ];
> Is this replaced dynamically by the bootloader? Otherwise this
> suggests all boards use the same MAC address.
Yes, this is replaced during production. In fact it could be 00 00 00
00 00 00 as well.
The IP address assigned here allows the device to be recognizable on
the network even when the full "flashing" is not successful.
> > + status = "okay";
> > +
> > + mdio {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + mac0_phy: ethernet-phy@0 {
> > + /* LAN8720Ai - PHY ID */
> > + compatible =
> > "ethernet-phy-id0007.c0f0","ethernet-phy-ieee802.3-c22";
> > + reg = <0>;
> > + smsc,disable-energy-detect;
> > + max-speed = <100>;
> > +
> > + reset-gpios = <&gpio4 12 GPIO_ACTIVE_LOW>;
> > /* GPIO4_12 */
> I think the comment only repeat what is already defined here.
Yes - I will remove it.
> > + reset-assert-us = <1000>;
> > + reset-deassert-us = <1000>;
> > + };
> > + };
> > +};
> > +
> > +&pinctrl {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&hog_pins_a>, <&hog_pins_rev>;
> > +
> > + hog_pins_a: hog@0 {
> > + reg = <0>;
> > + fsl,pinmux-ids = <
> > + MX28_PAD_GPMI_RDY2__GPIO_0_22
> > + MX28_PAD_GPMI_RDY3__GPIO_0_23
> > + MX28_PAD_GPMI_RDN__GPIO_0_24
> > + MX28_PAD_LCD_VSYNC__GPIO_1_28
> > + MX28_PAD_SSP2_SS1__GPIO_2_20
> > + MX28_PAD_SSP2_SS2__GPIO_2_21
> > + MX28_PAD_AUART2_CTS__GPIO_3_10
> > + MX28_PAD_AUART2_RTS__GPIO_3_11
> > + MX28_PAD_GPMI_WRN__GPIO_0_25
> > + MX28_PAD_ENET0_RXD2__GPIO_4_9
> > + MX28_PAD_ENET0_TXD2__GPIO_4_11
> > + >;
> > + fsl,drive-strength = <MXS_DRIVE_4mA>;
> > + fsl,voltage = <MXS_VOLTAGE_HIGH>;
> > + fsl,pull-up = <MXS_PULL_DISABLE>;
> > + };
> > +
> > + hog_pins_rev: hog@1 {
> > + reg = <1>;
> > + fsl,pinmux-ids = <
> > + MX28_PAD_ENET0_RXD3__GPIO_4_10
> > + MX28_PAD_ENET0_TX_CLK__GPIO_4_5
> > + MX28_PAD_ENET0_COL__GPIO_4_14
> > + MX28_PAD_ENET0_CRS__GPIO_4_15
> > + >;
> > + fsl,drive-strength = <MXS_DRIVE_4mA>;
> > + fsl,voltage = <MXS_VOLTAGE_HIGH>;
> > + fsl,pull-up = <MXS_PULL_DISABLE>;
> > + };
> > +
> > + keypad_pins_bttc: keypad-bttc@0 {
> > + reg = <0>;
> > + fsl,pinmux-ids = <
> > + MX28_PAD_GPMI_D00__GPIO_0_0
> > + MX28_PAD_AUART0_CTS__GPIO_3_2
> > + MX28_PAD_AUART0_RTS__GPIO_3_3
> > + MX28_PAD_GPMI_D03__GPIO_0_3
> > + MX28_PAD_GPMI_D04__GPIO_0_4
> > + MX28_PAD_GPMI_D05__GPIO_0_5
> > + MX28_PAD_GPMI_D06__GPIO_0_6
> > + MX28_PAD_GPMI_D07__GPIO_0_7
> > + MX28_PAD_GPMI_CE1N__GPIO_0_17
> > + MX28_PAD_GPMI_CE2N__GPIO_0_18
> > + MX28_PAD_GPMI_CE3N__GPIO_0_19
> > + MX28_PAD_GPMI_RDY0__GPIO_0_20
> > + >;
> > + fsl,drive-strength = <MXS_DRIVE_4mA>;
> > + fsl,voltage = <MXS_VOLTAGE_HIGH>;
> > + fsl,pull-up = <MXS_PULL_DISABLE>;
> > + };
> > +
> > + lcdif_sync_pins_bttc: lcdif-bttc@0 {
> > + reg = <0>;
> > + fsl,pinmux-ids = <
> > + MX28_PAD_LCD_DOTCLK__LCD_DOTCLK
> > + MX28_PAD_LCD_ENABLE__LCD_ENABLE
> > + MX28_PAD_LCD_HSYNC__LCD_HSYNC
> > + MX28_PAD_LCD_RD_E__LCD_VSYNC
> > + >;
> > + fsl,drive-strength = <MXS_DRIVE_4mA>;
> > + fsl,voltage = <MXS_VOLTAGE_HIGH>;
> > + fsl,pull-up = <MXS_PULL_DISABLE>;
> > + };
> > +
> > + lcdif_reset_pins_bttc: lcdif-bttc@1 {
> > + reg = <1>;
> > + fsl,pinmux-ids = <
> > + MX28_PAD_LCD_RESET__GPIO_3_30
> > + >;
> > + fsl,drive-strength = <MXS_DRIVE_4mA>;
> > + fsl,voltage = <MXS_VOLTAGE_HIGH>;
> > + fsl,pull-up = <MXS_PULL_ENABLE>;
> > + };
> > +
> > + ssp1_sdio_pins_a: ssp1-sdio@0 {
> > + reg = <0>;
> > + fsl,pinmux-ids = <
> > + MX28_PAD_SSP1_DATA0__SSP1_D0
> > + MX28_PAD_GPMI_D01__SSP1_D1
> > + MX28_PAD_GPMI_D02__SSP1_D2
> > + MX28_PAD_SSP1_DATA3__SSP1_D3
> > + MX28_PAD_SSP1_CMD__SSP1_CMD
> > + MX28_PAD_SSP1_SCK__SSP1_SCK
> > + >;
> > + fsl,drive-strength = <MXS_DRIVE_8mA>;
> > + fsl,voltage = <MXS_VOLTAGE_HIGH>;
> > + fsl,pull-up = <MXS_PULL_ENABLE>;
> > + };
> > +
> > + wifi_en_pin_bttc: wifi_en_pin@0 {
> This should trigger a schema warning. The node name should use dashes
> instead of underscore.
IIRC - there was no schema warning for it.
> > + reg = <0>;
> > + fsl,pinmux-ids = <
> > + MX28_PAD_GPMI_CLE__GPIO_0_27
> > + >;
> > + fsl,drive-strength = <MXS_DRIVE_8mA>;
> > + fsl,voltage = <MXS_VOLTAGE_HIGH>;
> > + fsl,pull-up = <MXS_PULL_ENABLE>;
> > + };
> > +};
> > +
> > +&pwm {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pwm3_pins_a>;
> > + status = "okay";
> > +};
> > +
> > +®_usb_5v {
> > + gpio = <&gpio1 28 0>;
> Please use polarity define.
Ok.
> > +};
> > +
> > +&saif0 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&saif0_pins_a>;
> > + #sound-dai-cells = <0>;
> > + assigned-clocks = <&clks 53>;
> > + assigned-clock-rates = <12000000>;
> > + status = "okay";
> > +};
> > +
> > +&saif1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&saif1_pins_a>;
> > + fsl,saif-master = <&saif0>;
> > + #sound-dai-cells = <0>;
> > + status = "okay";
> > +};
> > +
> > +&ssp1 {
> > + compatible = "fsl,imx28-mmc";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&ssp1_sdio_pins_a>;
> > + bus-width = <4>;
> > + no-1-8-v; /* force 3.3V VIO */
> > + pm-ignore-notify;
> This seems to be undocumented.
Maybe this is a reminder from older DTS version. Anyway - I will remove
it.
> > + non-removable;
> > + vmmc-supply = <®_3v3>;
> > + mmc-pwrseq = <&wifi_pwrseq>;
> > + keep-power-in-suspend;
> > + status = "okay";
> > +
> > + wlan@1 {
> > + reg = <1>;
> > + compatible = "brcm,bcm4329-fmac";
> > + };
> > +};
> > +
> > +&ssp2 {
> > + compatible = "fsl,imx28-spi";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&spi2_pins_a>;
> > + status = "okay";
> > +};
>
Best regards,
Lukasz Majewski
--
DENX Software Engineering GmbH, Managing Director: Erika Unter
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: lukma@xxxxxxx
Attachment:
pgpl_rIthQoMU.pgp
Description: OpenPGP digital signature
