Use newly defined 'active-high' property to set the
VEND1_GLOBAL_LED_DRIVE_VDD bit and let 'active-low' clear that bit. This
reflects the technical reality which was inverted in the previous
description in which the 'active-low' property was used to actually set
the VEND1_GLOBAL_LED_DRIVE_VDD bit, which means that VDD (ie. supply
voltage) of the LED is driven rather than GND.
Signed-off-by: Daniel Golle <daniel@xxxxxxxxxxxxxx>
---
drivers/net/phy/aquantia/aquantia.h | 1 +
drivers/net/phy/aquantia/aquantia_leds.c | 6 +++++-
drivers/net/phy/aquantia/aquantia_main.c | 12 +++++++++---
3 files changed, 15 insertions(+), 4 deletions(-)
diff --git a/drivers/net/phy/aquantia/aquantia.h b/drivers/net/phy/aquantia/aquantia.h
index 2465345081f8..0c78bfabace5 100644
--- a/drivers/net/phy/aquantia/aquantia.h
+++ b/drivers/net/phy/aquantia/aquantia.h
@@ -177,6 +177,7 @@ static const struct aqr107_hw_stat aqr107_hw_stats[] = {
struct aqr107_priv {
u64 sgmii_stats[AQR107_SGMII_STAT_SZ];
unsigned long leds_active_low;
+ unsigned long leds_active_high;
};
#if IS_REACHABLE(CONFIG_HWMON)
diff --git a/drivers/net/phy/aquantia/aquantia_leds.c b/drivers/net/phy/aquantia/aquantia_leds.c
index 201c8df93fad..21b8ede2a105 100644
--- a/drivers/net/phy/aquantia/aquantia_leds.c
+++ b/drivers/net/phy/aquantia/aquantia_leds.c
@@ -121,7 +121,7 @@ int aqr_phy_led_active_low_set(struct phy_device *phydev, int index, bool enable
{
return phy_modify_mmd(phydev, MDIO_MMD_VEND1, AQR_LED_DRIVE(index),
VEND1_GLOBAL_LED_DRIVE_VDD,
- enable ? VEND1_GLOBAL_LED_DRIVE_VDD : 0);
+ enable ? 0 : VEND1_GLOBAL_LED_DRIVE_VDD);
}
int aqr_phy_led_polarity_set(struct phy_device *phydev, int index, unsigned long modes)
@@ -138,6 +138,8 @@ int aqr_phy_led_polarity_set(struct phy_device *phydev, int index, unsigned long
case PHY_LED_ACTIVE_LOW:
active_low = true;
break;
+ case PHY_LED_ACTIVE_HIGH:
+ break;
default:
return -EINVAL;
}
@@ -146,6 +148,8 @@ int aqr_phy_led_polarity_set(struct phy_device *phydev, int index, unsigned long
/* Save LED driver vdd state to restore on SW reset */
if (active_low)
priv->leds_active_low |= BIT(index);
+ else
+ priv->leds_active_high |= BIT(index);
return aqr_phy_led_active_low_set(phydev, index, active_low);
}
diff --git a/drivers/net/phy/aquantia/aquantia_main.c b/drivers/net/phy/aquantia/aquantia_main.c
index c33a5ef34ba0..c7381d5ede37 100644
--- a/drivers/net/phy/aquantia/aquantia_main.c
+++ b/drivers/net/phy/aquantia/aquantia_main.c
@@ -488,7 +488,7 @@ static void aqr107_chip_info(struct phy_device *phydev)
static int aqr107_config_init(struct phy_device *phydev)
{
struct aqr107_priv *priv = phydev->priv;
- u32 led_active_low;
+ u32 led_idx;
int ret;
/* Check that the PHY interface type is compatible */
@@ -515,8 +515,14 @@ static int aqr107_config_init(struct phy_device *phydev)
return ret;
/* Restore LED polarity state after reset */
- for_each_set_bit(led_active_low, &priv->leds_active_low, AQR_MAX_LEDS) {
- ret = aqr_phy_led_active_low_set(phydev, led_active_low, true);
+ for_each_set_bit(led_idx, &priv->leds_active_low, AQR_MAX_LEDS) {
+ ret = aqr_phy_led_active_low_set(phydev, led_idx, true);
+ if (ret)
+ return ret;
+ }
+
+ for_each_set_bit(led_idx, &priv->leds_active_high, AQR_MAX_LEDS) {
+ ret = aqr_phy_led_active_low_set(phydev, led_idx, false);
if (ret)
return ret;
}
--
2.46.2
