Changes in v5: - Fixes smatch CI splat - Link to v4: https://lore.kernel.org/r/20241003-b4-master-24-11-25-ov08x40-v4-0-7ee2c45fdc8c@xxxxxxxxxx Changes in v4: - Drops link-frequencies from properties: as discussed here: https://lore.kernel.org/r/Zv6STSKeNNlT83ux@kekkonen.localdomain - Link to v3: https://lore.kernel.org/r/20241002-b4-master-24-11-25-ov08x40-v3-0-483bcdcf8886@xxxxxxxxxx Changes in v3: - Drops assigned-clock-* from description retains in example - Sakari, Krzysztof - Updates example fake clock names to ov08x40_* instead of copy/paste ov9282_clk -> ov08x40_clk, ov9282_clk_parent -> ov08x40_clk_parent - bod - Link to v2: https://lore.kernel.org/r/20241001-b4-master-24-11-25-ov08x40-v2-0-e478976b20c1@xxxxxxxxxx Changes in v2: - Drops "-" in ovti,ov08x40.yaml after description: - Rob - Adds ":" after first line of description text - Rob - dts -> DT in commit log - Rob - Removes dependency on 'xvclk' as a name in yaml and driver - Sakari - Uses assigned-clock, assigned-clock-parents and assigned-clock-rates - Sakari - Drops clock-frequency - Sakarai, Krzysztof - Drops dovdd-supply, avdd-supply, dvdd-supply and reset-gpios as required, its perfectly possible not to have the reset GPIO or the power rails under control of the SoC. - bod - Link to v1: https://lore.kernel.org/r/20240926-b4-master-24-11-25-ov08x40-v1-0-e4d5fbd3b58a@xxxxxxxxxx V1: This series brings fixes and updates to ov08x40 which allows for use of this sensor on the Qualcomm x1e80100 CRD but also on any other dts based system. Firstly there's a fix for the pseudo burst mode code that was added in 8f667d202384 ("media: ov08x40: Reduce start streaming time"). Not every I2C controller can handle an arbitrary sized write, this is the case on Qualcomm CAMSS/CCI I2C sensor interfaces which limit the transaction size and communicate this limit via I2C quirks. A simple fix to optionally break up the large submitted burst into chunks not exceeding adapter->quirk size fixes. Secondly then is addition of a yaml description for the ov08x40 and extension of the driver to support OF probe and powering on of the power rails from the driver instead of from ACPI. Once done the sensor works without further modification on the Qualcomm x1e80100 CRD. Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@xxxxxxxxxx> --- Bryan O'Donoghue (4): media: ov08x40: Fix burst write sequence media: dt-bindings: Add OmniVision OV08X40 media: ov08x40: Rename ext_clk to xvclk media: ov08x40: Add OF probe support .../bindings/media/i2c/ovti,ov08x40.yaml | 114 +++++++++++++ drivers/media/i2c/ov08x40.c | 181 ++++++++++++++++++--- 2 files changed, 271 insertions(+), 24 deletions(-) --- base-commit: 2b7275670032a98cba266bd1b8905f755b3e650f change-id: 20240926-b4-master-24-11-25-ov08x40-c6f477aaa6a4 Best regards, -- Bryan O'Donoghue <bryan.odonoghue@xxxxxxxxxx>
