Re: [PATCH v3 2/3] net: stmmac: Add glue layer for T-HEAD TH1520 SoC

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Tue, Oct 01, 2024 at 02:48:13AM -0700, Emil Renner Berthing wrote:
> Drew Fustini wrote:
> > From: Jisheng Zhang <jszhang@xxxxxxxxxx>
> >
> > Add dwmac glue driver to support the DesignWare-based GMAC controllers
> > on the T-HEAD TH1520 SoC.
> >
> > Signed-off-by: Jisheng Zhang <jszhang@xxxxxxxxxx>
> > [esmil: rename plat->interface -> plat->mac_interface,
> >         use devm_stmmac_probe_config_dt()]
> > Signed-off-by: Emil Renner Berthing <emil.renner.berthing@xxxxxxxxxxxxx>
> > [drew: convert from stmmac_dvr_probe() to devm_stmmac_pltfr_probe()]
> > Signed-off-by: Drew Fustini <dfustini@xxxxxxxxxxxxxxx>
> > ---
> >  MAINTAINERS                                       |   1 +
> >  drivers/net/ethernet/stmicro/stmmac/Kconfig       |  11 +
> >  drivers/net/ethernet/stmicro/stmmac/Makefile      |   1 +
> >  drivers/net/ethernet/stmicro/stmmac/dwmac-thead.c | 291 ++++++++++++++++++++++
> >  4 files changed, 304 insertions(+)
> >
> > diff --git a/MAINTAINERS b/MAINTAINERS
> > index 9e50107efb37..1d24863c01df 100644
> > --- a/MAINTAINERS
> > +++ b/MAINTAINERS
> > @@ -19946,6 +19946,7 @@ F:	Documentation/devicetree/bindings/net/thead,th1520-gmac.yaml
> >  F:	Documentation/devicetree/bindings/pinctrl/thead,th1520-pinctrl.yaml
> >  F:	arch/riscv/boot/dts/thead/
> >  F:	drivers/clk/thead/clk-th1520-ap.c
> > +F:	drivers/net/ethernet/stmicro/stmmac/dwmac-thead.c
> >  F:	drivers/pinctrl/pinctrl-th1520.c
> >  F:	include/dt-bindings/clock/thead,th1520-clk-ap.h
> >
> > diff --git a/drivers/net/ethernet/stmicro/stmmac/Kconfig b/drivers/net/ethernet/stmicro/stmmac/Kconfig
> > index 05cc07b8f48c..82030adaf16e 100644
> > --- a/drivers/net/ethernet/stmicro/stmmac/Kconfig
> > +++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig
> > @@ -228,6 +228,17 @@ config DWMAC_SUN8I
> >  	  stmmac device driver. This driver is used for H3/A83T/A64
> >  	  EMAC ethernet controller.
> >
> > +config DWMAC_THEAD
> > +	tristate "T-HEAD dwmac support"
> > +	depends on OF && (ARCH_THEAD || COMPILE_TEST)
> > +	select MFD_SYSCON
> > +	help
> > +	  Support for ethernet controllers on T-HEAD RISC-V SoCs
> > +
> > +	  This selects the T-HEAD platform specific glue layer support for
> > +	  the stmmac device driver. This driver is used for T-HEAD TH1520
> > +	  ethernet controller.
> > +
> >  config DWMAC_IMX8
> >  	tristate "NXP IMX8 DWMAC support"
> >  	default ARCH_MXC
> > diff --git a/drivers/net/ethernet/stmicro/stmmac/Makefile b/drivers/net/ethernet/stmicro/stmmac/Makefile
> > index c2f0e91f6bf8..d065634c6223 100644
> > --- a/drivers/net/ethernet/stmicro/stmmac/Makefile
> > +++ b/drivers/net/ethernet/stmicro/stmmac/Makefile
> > @@ -28,6 +28,7 @@ obj-$(CONFIG_DWMAC_STI)		+= dwmac-sti.o
> >  obj-$(CONFIG_DWMAC_STM32)	+= dwmac-stm32.o
> >  obj-$(CONFIG_DWMAC_SUNXI)	+= dwmac-sunxi.o
> >  obj-$(CONFIG_DWMAC_SUN8I)	+= dwmac-sun8i.o
> > +obj-$(CONFIG_DWMAC_THEAD)	+= dwmac-thead.o
> >  obj-$(CONFIG_DWMAC_DWC_QOS_ETH)	+= dwmac-dwc-qos-eth.o
> >  obj-$(CONFIG_DWMAC_INTEL_PLAT)	+= dwmac-intel-plat.o
> >  obj-$(CONFIG_DWMAC_LOONGSON1)	+= dwmac-loongson1.o
> > diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-thead.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-thead.c
> > new file mode 100644
> > index 000000000000..f2f94539c0d2
> > --- /dev/null
> > +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-thead.c
> > @@ -0,0 +1,291 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * T-HEAD DWMAC platform driver
> > + *
> > + * Copyright (C) 2021 Alibaba Group Holding Limited.
> > + * Copyright (C) 2023 Jisheng Zhang <jszhang@xxxxxxxxxx>
> > + *
> > + */
> > +
> > +#include <linux/bitfield.h>
> > +#include <linux/module.h>
> > +#include <linux/of.h>
> > +#include <linux/of_device.h>
> > +#include <linux/of_net.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/regmap.h>
> > +
> > +#include "stmmac_platform.h"
> > +
> > +#define GMAC_CLK_EN			0x00
> > +#define  GMAC_TX_CLK_EN			BIT(1)
> > +#define  GMAC_TX_CLK_N_EN		BIT(2)
> > +#define  GMAC_TX_CLK_OUT_EN		BIT(3)
> > +#define  GMAC_RX_CLK_EN			BIT(4)
> > +#define  GMAC_RX_CLK_N_EN		BIT(5)
> > +#define  GMAC_EPHY_REF_CLK_EN		BIT(6)
> > +#define GMAC_RXCLK_DELAY_CTRL		0x04
> > +#define  GMAC_RXCLK_BYPASS		BIT(15)
> > +#define  GMAC_RXCLK_INVERT		BIT(14)
> > +#define  GMAC_RXCLK_DELAY_MASK		GENMASK(4, 0)
> > +#define  GMAC_RXCLK_DELAY_VAL(x)	FIELD_PREP(GMAC_RXCLK_DELAY_MASK, (x))
> > +#define GMAC_TXCLK_DELAY_CTRL		0x08
> > +#define  GMAC_TXCLK_BYPASS		BIT(15)
> > +#define  GMAC_TXCLK_INVERT		BIT(14)
> > +#define  GMAC_TXCLK_DELAY_MASK		GENMASK(4, 0)
> > +#define  GMAC_TXCLK_DELAY_VAL(x)	FIELD_PREP(GMAC_RXCLK_DELAY_MASK, (x))
> > +#define GMAC_PLLCLK_DIV			0x0c
> > +#define  GMAC_PLLCLK_DIV_EN		BIT(31)
> > +#define  GMAC_PLLCLK_DIV_MASK		GENMASK(7, 0)
> > +#define  GMAC_PLLCLK_DIV_NUM(x)		FIELD_PREP(GMAC_PLLCLK_DIV_MASK, (x))
> > +#define GMAC_GTXCLK_SEL			0x18
> > +#define  GMAC_GTXCLK_SEL_PLL		BIT(0)
> > +#define GMAC_INTF_CTRL			0x1c
> > +#define  PHY_INTF_MASK			BIT(0)
> > +#define  PHY_INTF_RGMII			FIELD_PREP(PHY_INTF_MASK, 1)
> > +#define  PHY_INTF_MII_GMII		FIELD_PREP(PHY_INTF_MASK, 0)
> > +#define GMAC_TXCLK_OEN			0x20
> > +#define  TXCLK_DIR_MASK			BIT(0)
> > +#define  TXCLK_DIR_OUTPUT		FIELD_PREP(TXCLK_DIR_MASK, 0)
> > +#define  TXCLK_DIR_INPUT		FIELD_PREP(TXCLK_DIR_MASK, 1)
> > +
> > +#define GMAC_GMII_RGMII_RATE	125000000
> > +#define GMAC_MII_RATE		25000000
> > +
> > +static const struct regmap_config regmap_config = {
> > +	.reg_bits = 32,
> > +	.val_bits = 32,
> > +	.reg_stride = 4,
> > +};
> > +
> > +struct thead_dwmac {
> > +	struct plat_stmmacenet_data *plat;
> > +	struct regmap *apb_regmap;
> > +	struct device *dev;
> > +};
> > +
> > +static int thead_dwmac_set_phy_if(struct plat_stmmacenet_data *plat)
> > +{
> > +	struct thead_dwmac *dwmac = plat->bsp_priv;
> > +	u32 phyif;
> > +
> > +	switch (plat->mac_interface) {
> > +	case PHY_INTERFACE_MODE_MII:
> > +		phyif = PHY_INTF_MII_GMII;
> > +		break;
> > +	case PHY_INTERFACE_MODE_RGMII:
> > +	case PHY_INTERFACE_MODE_RGMII_ID:
> > +	case PHY_INTERFACE_MODE_RGMII_TXID:
> > +	case PHY_INTERFACE_MODE_RGMII_RXID:
> > +		phyif = PHY_INTF_RGMII;
> > +		break;
> > +	default:
> > +		dev_err(dwmac->dev, "unsupported phy interface %d\n",
> > +			plat->mac_interface);
> > +		return -EINVAL;
> > +	};
> > +
> > +	return regmap_write(dwmac->apb_regmap, GMAC_INTF_CTRL, phyif);
> > +}
> > +
> > +static int thead_dwmac_set_txclk_dir(struct plat_stmmacenet_data *plat)
> > +{
> > +	struct thead_dwmac *dwmac = plat->bsp_priv;
> > +	u32 txclk_dir;
> > +
> > +	switch (plat->mac_interface) {
> > +	case PHY_INTERFACE_MODE_MII:
> > +		txclk_dir = TXCLK_DIR_INPUT;
> > +		break;
> > +	case PHY_INTERFACE_MODE_RGMII:
> > +	case PHY_INTERFACE_MODE_RGMII_ID:
> > +	case PHY_INTERFACE_MODE_RGMII_TXID:
> > +	case PHY_INTERFACE_MODE_RGMII_RXID:
> > +		txclk_dir = TXCLK_DIR_OUTPUT;
> > +		break;
> > +	default:
> > +		dev_err(dwmac->dev, "unsupported phy interface %d\n",
> > +			plat->mac_interface);
> > +		return -EINVAL;
> > +	};
> > +
> > +	return regmap_write(dwmac->apb_regmap, GMAC_TXCLK_OEN, txclk_dir);
> > +}
> > +
> > +static void thead_dwmac_fix_speed(void *priv, unsigned int speed, unsigned int mode)
> > +{
> > +	struct plat_stmmacenet_data *plat;
> > +	struct thead_dwmac *dwmac = priv;
> > +	unsigned long rate;
> > +	u32 div;
> > +
> > +	plat = dwmac->plat;
> > +
> > +	switch (plat->mac_interface) {
> > +	/* For MII, rxc/txc is provided by phy */
> > +	case PHY_INTERFACE_MODE_MII:
> > +		return;
> > +
> > +	case PHY_INTERFACE_MODE_RGMII:
> > +	case PHY_INTERFACE_MODE_RGMII_ID:
> > +	case PHY_INTERFACE_MODE_RGMII_RXID:
> > +	case PHY_INTERFACE_MODE_RGMII_TXID:
> > +		rate = clk_get_rate(plat->stmmac_clk);
> > +		if (!rate || rate % GMAC_GMII_RGMII_RATE != 0 ||
> > +		    rate % GMAC_MII_RATE != 0) {
> > +			dev_err(dwmac->dev, "invalid gmac rate %ld\n", rate);
> > +			return;
> > +		}
> > +
> > +		regmap_update_bits(dwmac->apb_regmap, GMAC_PLLCLK_DIV, GMAC_PLLCLK_DIV_EN, 0);
> > +
> > +		switch (speed) {
> > +		case SPEED_1000:
> > +			div = rate / GMAC_GMII_RGMII_RATE;
> > +			break;
> > +		case SPEED_100:
> > +			div = rate / GMAC_MII_RATE;
> > +			break;
> > +		case SPEED_10:
> > +			div = rate * 10 / GMAC_MII_RATE;
> > +			break;
> > +		default:
> > +			dev_err(dwmac->dev, "invalid speed %u\n", speed);
> > +			return;
> > +		}
> > +		regmap_update_bits(dwmac->apb_regmap, GMAC_PLLCLK_DIV,
> > +				   GMAC_PLLCLK_DIV_MASK, GMAC_PLLCLK_DIV_NUM(div));
> > +
> > +		regmap_update_bits(dwmac->apb_regmap, GMAC_PLLCLK_DIV,
> > +				   GMAC_PLLCLK_DIV_EN, GMAC_PLLCLK_DIV_EN);
> > +		break;
> > +	default:
> > +		dev_err(dwmac->dev, "unsupported phy interface %d\n",
> > +			plat->mac_interface);
> > +		return;
> > +	}
> > +}
> > +
> > +static int thead_dwmac_enable_clk(struct plat_stmmacenet_data *plat)
> > +{
> > +	struct thead_dwmac *dwmac = plat->bsp_priv;
> > +	int err;
> > +	u32 reg;
> > +
> > +	switch (plat->mac_interface) {
> > +	case PHY_INTERFACE_MODE_MII:
> > +		reg = GMAC_RX_CLK_EN | GMAC_TX_CLK_EN;
> > +		break;
> > +
> > +	case PHY_INTERFACE_MODE_RGMII:
> > +	case PHY_INTERFACE_MODE_RGMII_ID:
> > +	case PHY_INTERFACE_MODE_RGMII_RXID:
> > +	case PHY_INTERFACE_MODE_RGMII_TXID:
> > +		/* use pll */
> > +		err = regmap_write(dwmac->apb_regmap, GMAC_GTXCLK_SEL, GMAC_GTXCLK_SEL_PLL);
> > +		if (err)
> > +			return dev_err_probe(dwmac->dev, err,
> > +					     "failed to set phy interface\n");
> > +
> > +		reg = GMAC_TX_CLK_EN | GMAC_TX_CLK_N_EN | GMAC_TX_CLK_OUT_EN |
> > +		      GMAC_RX_CLK_EN | GMAC_RX_CLK_N_EN;
> > +		break;
> > +
> > +	default:
> > +		dev_err(dwmac->dev, "unsupported phy interface %d\n",
> > +			plat->mac_interface);
> > +		return -EINVAL;
> > +	}
> > +
> > +	return regmap_write(dwmac->apb_regmap, GMAC_CLK_EN, reg);
> > +}
> > +
> > +static int thead_dwmac_init(struct platform_device *pdev, void *priv)
> > +{
> > +	struct thead_dwmac *dwmac = priv;
> > +	int ret;
> > +
> > +	ret = thead_dwmac_set_phy_if(dwmac->plat);
> > +	if (ret)
> > +		return ret;
> > +
> > +	ret = thead_dwmac_set_txclk_dir(dwmac->plat);
> > +	if (ret)
> > +		return ret;
> > +
> > +	ret = regmap_write(dwmac->apb_regmap, GMAC_RXCLK_DELAY_CTRL,
> > +			   GMAC_RXCLK_DELAY_VAL(0));
> > +	if (ret)
> > +		return dev_err_probe(dwmac->dev, ret,
> > +				     "failed to set GMAC RX clock delay\n");
> > +
> > +	ret = regmap_write(dwmac->apb_regmap, GMAC_TXCLK_DELAY_CTRL,
> > +			   GMAC_TXCLK_DELAY_VAL(0));
> > +	if (ret)
> > +		return dev_err_probe(dwmac->dev, ret,
> > +				     "failed to set GMAC TX clock delay\n");
> > +
> > +	return thead_dwmac_enable_clk(dwmac->plat);
> > +}
> > +
> > +static int thead_dwmac_probe(struct platform_device *pdev)
> > +{
> > +	struct stmmac_resources stmmac_res;
> > +	struct plat_stmmacenet_data *plat;
> > +	struct thead_dwmac *dwmac;
> > +	void __iomem *apb;
> > +	int ret;
> > +
> > +	ret = stmmac_get_platform_resources(pdev, &stmmac_res);
> > +	if (ret)
> > +		return dev_err_probe(&pdev->dev, ret,
> > +				     "failed to get resources\n");
> > +
> > +	plat = devm_stmmac_probe_config_dt(pdev, stmmac_res.mac);
> > +	if (IS_ERR(plat))
> > +		return dev_err_probe(&pdev->dev, PTR_ERR(plat),
> > +				     "dt configuration failed\n");
> > +
> > +	dwmac = devm_kzalloc(&pdev->dev, sizeof(*dwmac), GFP_KERNEL);
> > +	if (!dwmac)
> > +		return -ENOMEM;
> > +
> > +	apb = devm_platform_ioremap_resource(pdev, 1);
> > +	if (IS_ERR(apb))
> > +		return dev_err_probe(&pdev->dev, PTR_ERR(apb),
> > +				     "Failed to remap gmac apb registers\n");
> > +
> > +	dwmac->apb_regmap = devm_regmap_init_mmio(&pdev->dev, apb, &regmap_config);
> > +	if (IS_ERR(dwmac->apb_regmap))
> > +		return dev_err_probe(&pdev->dev, PTR_ERR(dwmac->apb_regmap),
> > +				     "Failed to access gmac apb registers\n");
> 
> Why do you need to convert the APB range to a regmap? As far as I can tell it's
> just regular 32bit memory mapped registers, so should work fine with just
> readl()/writel()

Good point, I don't think there is any benefit to using regmap. I will
change the next revision to use writel() instead. I just tested this and
the network interface still works okay.

Thanks,
Drew

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-thead.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-thead.c
index f2f94539c0d2..df2fe0fdd128 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-thead.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-thead.c
@@ -13,7 +13,6 @@
 #include <linux/of_device.h>
 #include <linux/of_net.h>
 #include <linux/platform_device.h>
-#include <linux/regmap.h>
 
 #include "stmmac_platform.h"
 
@@ -52,15 +51,9 @@
 #define GMAC_GMII_RGMII_RATE	125000000
 #define GMAC_MII_RATE		25000000
 
-static const struct regmap_config regmap_config = {
-	.reg_bits = 32,
-	.val_bits = 32,
-	.reg_stride = 4,
-};
-
 struct thead_dwmac {
 	struct plat_stmmacenet_data *plat;
-	struct regmap *apb_regmap;
+	void __iomem *apb_base;
 	struct device *dev;
 };
 
@@ -85,7 +78,8 @@ static int thead_dwmac_set_phy_if(struct plat_stmmacenet_data *plat)
 		return -EINVAL;
 	};
 
-	return regmap_write(dwmac->apb_regmap, GMAC_INTF_CTRL, phyif);
+	writel(phyif, dwmac->apb_base + GMAC_INTF_CTRL);
+	return 0;
 }
 
 static int thead_dwmac_set_txclk_dir(struct plat_stmmacenet_data *plat)
@@ -109,7 +103,8 @@ static int thead_dwmac_set_txclk_dir(struct plat_stmmacenet_data *plat)
 		return -EINVAL;
 	};
 
-	return regmap_write(dwmac->apb_regmap, GMAC_TXCLK_OEN, txclk_dir);
+	writel(txclk_dir, dwmac->apb_base + GMAC_TXCLK_OEN);
+	return 0;
 }
 
 static void thead_dwmac_fix_speed(void *priv, unsigned int speed, unsigned int mode)
@@ -117,7 +112,7 @@ static void thead_dwmac_fix_speed(void *priv, unsigned int speed, unsigned int m
 	struct plat_stmmacenet_data *plat;
 	struct thead_dwmac *dwmac = priv;
 	unsigned long rate;
-	u32 div;
+	u32 div, reg;
 
 	plat = dwmac->plat;
 
@@ -137,7 +132,7 @@ static void thead_dwmac_fix_speed(void *priv, unsigned int speed, unsigned int m
 			return;
 		}
 
-		regmap_update_bits(dwmac->apb_regmap, GMAC_PLLCLK_DIV, GMAC_PLLCLK_DIV_EN, 0);
+		writel(FIELD_PREP(GMAC_PLLCLK_DIV_EN, 0), dwmac->apb_base + GMAC_PLLCLK_DIV);
 
 		switch (speed) {
 		case SPEED_1000:
@@ -153,11 +148,10 @@ static void thead_dwmac_fix_speed(void *priv, unsigned int speed, unsigned int m
 			dev_err(dwmac->dev, "invalid speed %u\n", speed);
 			return;
 		}
-		regmap_update_bits(dwmac->apb_regmap, GMAC_PLLCLK_DIV,
-				   GMAC_PLLCLK_DIV_MASK, GMAC_PLLCLK_DIV_NUM(div));
 
-		regmap_update_bits(dwmac->apb_regmap, GMAC_PLLCLK_DIV,
-				   GMAC_PLLCLK_DIV_EN, GMAC_PLLCLK_DIV_EN);
+		reg = FIELD_PREP(GMAC_PLLCLK_DIV_EN, 1) |
+		      FIELD_PREP(GMAC_PLLCLK_DIV_MASK, GMAC_PLLCLK_DIV_NUM(div));
+		writel(reg, dwmac->apb_base + GMAC_PLLCLK_DIV);
 		break;
 	default:
 		dev_err(dwmac->dev, "unsupported phy interface %d\n",
@@ -169,7 +163,6 @@ static void thead_dwmac_fix_speed(void *priv, unsigned int speed, unsigned int m
 static int thead_dwmac_enable_clk(struct plat_stmmacenet_data *plat)
 {
 	struct thead_dwmac *dwmac = plat->bsp_priv;
-	int err;
 	u32 reg;
 
 	switch (plat->mac_interface) {
@@ -182,11 +175,7 @@ static int thead_dwmac_enable_clk(struct plat_stmmacenet_data *plat)
 	case PHY_INTERFACE_MODE_RGMII_RXID:
 	case PHY_INTERFACE_MODE_RGMII_TXID:
 		/* use pll */
-		err = regmap_write(dwmac->apb_regmap, GMAC_GTXCLK_SEL, GMAC_GTXCLK_SEL_PLL);
-		if (err)
-			return dev_err_probe(dwmac->dev, err,
-					     "failed to set phy interface\n");
-
+		writel(GMAC_GTXCLK_SEL_PLL, dwmac->apb_base + GMAC_GTXCLK_SEL);
 		reg = GMAC_TX_CLK_EN | GMAC_TX_CLK_N_EN | GMAC_TX_CLK_OUT_EN |
 		      GMAC_RX_CLK_EN | GMAC_RX_CLK_N_EN;
 		break;
@@ -197,7 +186,8 @@ static int thead_dwmac_enable_clk(struct plat_stmmacenet_data *plat)
 		return -EINVAL;
 	}
 
-	return regmap_write(dwmac->apb_regmap, GMAC_CLK_EN, reg);
+	writel(reg, dwmac->apb_base + GMAC_CLK_EN);
+	return 0;
 }
 
 static int thead_dwmac_init(struct platform_device *pdev, void *priv)
@@ -213,17 +203,8 @@ static int thead_dwmac_init(struct platform_device *pdev, void *priv)
 	if (ret)
 		return ret;
 
-	ret = regmap_write(dwmac->apb_regmap, GMAC_RXCLK_DELAY_CTRL,
-			   GMAC_RXCLK_DELAY_VAL(0));
-	if (ret)
-		return dev_err_probe(dwmac->dev, ret,
-				     "failed to set GMAC RX clock delay\n");
-
-	ret = regmap_write(dwmac->apb_regmap, GMAC_TXCLK_DELAY_CTRL,
-			   GMAC_TXCLK_DELAY_VAL(0));
-	if (ret)
-		return dev_err_probe(dwmac->dev, ret,
-				     "failed to set GMAC TX clock delay\n");
+	writel(GMAC_RXCLK_DELAY_VAL(0), dwmac->apb_base + GMAC_RXCLK_DELAY_CTRL);
+	writel(GMAC_TXCLK_DELAY_VAL(0), dwmac->apb_base + GMAC_TXCLK_DELAY_CTRL);
 
 	return thead_dwmac_enable_clk(dwmac->plat);
 }
@@ -255,13 +236,9 @@ static int thead_dwmac_probe(struct platform_device *pdev)
 		return dev_err_probe(&pdev->dev, PTR_ERR(apb),
 				     "Failed to remap gmac apb registers\n");
 
-	dwmac->apb_regmap = devm_regmap_init_mmio(&pdev->dev, apb, &regmap_config);
-	if (IS_ERR(dwmac->apb_regmap))
-		return dev_err_probe(&pdev->dev, PTR_ERR(dwmac->apb_regmap),
-				     "Failed to access gmac apb registers\n");
-
 	dwmac->dev = &pdev->dev;
 	dwmac->plat = plat;
+	dwmac->apb_base = apb;
 	plat->bsp_priv = dwmac;
 	plat->fix_mac_speed = thead_dwmac_fix_speed;
 	plat->init = thead_dwmac_init;




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux