Re: [PATCH 2/3] dt-bindings: fpga: Add Efinix serial SPI programming bindings

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Am Sa., 28. Sept. 2024 um 14:53 Uhr schrieb Krzysztof Kozlowski
<krzk@xxxxxxxxxx>:
>
> On 28/09/2024 14:33, Ian Dannapel wrote:
> >>>>
> >>>>> +
> >>>>> +  spi-cpha: true
> >>>>> +
> >>>>> +  spi-cpol: true
> >>>>> +
> >>>>> +  spi-max-frequency:
> >>>>> +    maximum: 25000000
> >>>>> +
> >>>>> +  reg:
> >>>>> +    maxItems: 1
> >>>>> +
> >>>>> +  creset-gpios:
> >>>>
> >>>> reset-gpios
> >>>>
> >>>> Do not invent own properties.
> >>>>
> >>>>> +    description:
> >>>>> +      reset and re-configuration trigger pin (low active)
> >>>>> +    maxItems: 1
> >>>>> +
> >>>>> +  cs-gpios:
> >>>>> +    description:
> >>>>> +      chip-select pin (low active)
> >>>>
> >>>> Eee? That's a property of controller, not child. Aren't you duplicating
> >>>> existing controller property?
> >>> This device uses this pin in combination with the reset to enter the
> >>> programming mode. Also, the driver must guarantee that the pin is
> >>
> >> Isn't this the same on every SPI device?
> > Yes, but I was not very clear. In this case the pin must be hold
> > active including entering the programming mode. And if the controller
>
> Just like every CS, no?
>
> The only difference is that you must send entire programming sequence
> without releasing the CS.
>
> > transfers the data in bursts, the pin is also not allowed to go
> > inactive between transfer bursts.
> >>
> >>> active for the whole transfer process, including ending dummy bits.
> >>> This is why I added a warning to NOT use this driver with other
> >>> devices on the same bus.
> >>
> >> Not really related. None of this grants exception from duplicating
> >> controller's property.
> >>
> >> How do you think it will even work in Linux, if same GPIO is requested
> >> twice (imagine controller also has it)? Till now, this would be -EBUSY.
> > I expected that the controller is not able request the same gpio. From
> > the controller point of view, it is a device that does not have a chip
> > select. Not sure if the controller would be able to get to this gpio
> > if it is not explicitly given.
>
> But it could be given. Don't think only about your case.
it won't work if the controller also may request this gpio or interfere with it.
>
> Your description earlier clearly suggests it is CS. Description here
> suggests it is not a CS.
>
> No clue then.
>
> >>
> >> But regardless of implementation, I still do not understand why do you
> >> need duplicate same chip-select. Maybe just the naming is the confusion,
> >> dunno.
> > This could be an option to make the difference to a "real chip-select"
> > clear, but it would drift away from the datasheet naming. Eg,
> > prog-select?
>
> Please go back to datasheet. Which pin is this? CS, yes or not? If not,
> then which other pin is CS?
Yes, this pin in question is referred to as the Chip Select (CS) or
Slave Select in the datasheet and pinout.
It is used in combination with the reset for entering the programming
mode and then used for the SPI data transfer to the FPGA’s volatile
configuration RAM.
There must be no state change on this CS pin between entering
programming mode and the completion of the SPI transfer.
Since the controller chip-select functionality can't fulfill these
requirements for this device, the proposed solution is to move this
pin from the controller to the child driver.
>
> Best regards,
> Krzysztof
>
Best regards
Ian





[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux