Re: [PATCH 2/2] dt-bindings: mmc: mtk-sd: Add support for MT8196

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 28/09/2024 15:14, Andy-ld Lu (卢东) wrote:
> On Thu, 2024-09-26 at 12:54 -0500, Rob Herring wrote:
>>  	 
>> External email : Please do not click links or open attachments until
>> you have verified the sender or the content.
>>  On Thu, Sep 26, 2024 at 03:03:18PM +0800, Andy-ld Lu wrote:
>>> Extend the devicetree bindings to include the MT8196 mmc controller
>>> by adding the compatible string 'mediatek,msdc-v2', which could be
>>> also used for future compatible SoCs that support new tx/rx.
>>
>> Generally, every SoC ends up changing at least slightly. So we don't
>> do 
>> version numbers except when there's a well defined versioning scheme
>> of 
>> the h/w (e.g. FPGA IP blocks). So, use SoC for compatible string.
> Thanks for your review.
> 
> The new tx/rx represents a significant update for mmc controller of
> mediatek from the MT8196 chipset, and the dependent settings remain
> consistent for MT8196 and subsequent SoCs. Therefore, It is proposed to
> use a unified compatible string for these SoCs that support new tx/rx,
> and name it as 'IP(msdc) version two'.

Sorry, nope. That's not valid reasons.

>>
>>>
>>> Add three properties for MT8196 settings:
>>> - 'mediatek,prohibit-gate-cg', indicate if the source clock CG
>> could
>>>   be disabled when CPU access IP registers.
>>>
>>> - 'mediatek,stop-dly-sel', configure read data clock stops at block
>> gap.
>>>
>>> - 'mediatek,pop-en-cnt', configure the margins of write and read
>>>   pointers while begin to pop data transfer.
>>>
>>> Signed-off-by: Andy-ld Lu <andy-ld.lu@xxxxxxxxxxxx>
>>> ---
>>>  .../devicetree/bindings/mmc/mtk-sd.yaml       | 26
>> +++++++++++++++++++
>>>  1 file changed, 26 insertions(+)
>>>
>>> diff --git a/Documentation/devicetree/bindings/mmc/mtk-sd.yaml
>> b/Documentation/devicetree/bindings/mmc/mtk-sd.yaml
>>> index c532ec92d2d9..82d1a9fac67c 100644
>>> --- a/Documentation/devicetree/bindings/mmc/mtk-sd.yaml
>>> +++ b/Documentation/devicetree/bindings/mmc/mtk-sd.yaml
>>> @@ -25,6 +25,7 @@ properties:
>>>            - mediatek,mt8173-mmc
>>>            - mediatek,mt8183-mmc
>>>            - mediatek,mt8516-mmc
>>> +          - mediatek,msdc-v2
>>>        - items:
>>>            - const: mediatek,mt7623-mmc
>>>            - const: mediatek,mt2701-mmc
>>> @@ -154,6 +155,30 @@ properties:
>>>      enum: [32, 64]
>>>      default: 32
>>>  
>>> +  mediatek,stop-dly-sel:
>>> +    $ref: /schemas/types.yaml#/definitions/uint32
>>> +    description:
>>> +      Some SoCs need to set appropriate stop-dly-sel to configure
>> read data clock
>>> +      stops at block gap. The valid range is from 0 to 0xf.
>>
>> SoC dependent or board dependent? Imply from the compatible for the 
>> former. A property is fine for the latter case.
> Yes, it is SoC dependent in principle, but we would like to use a
> unified compatible string for MT8196 and subsequent SoCs as mentioned

Also no :(. Use SoC specific compatible.

> above, and this register setting(not relavant with new tx/rx) may be
> variant. Therefore, want to use the property of device tree to set
> individually.
>>
>>> +    minimum: 0
>>> +    maximum: 0xf
>>> +
>>> +  mediatek,pop-en-cnt:
>>> +    $ref: /schemas/types.yaml#/definitions/uint32
>>> +    description:
>>> +      Some SoCs need to set appropriate pop-en-cnt to configure
>> the margins of write
>>> +      and read pointers while begin to pop data transfer. The
>> valid range is from 0
>>> +      to 0xf.
>>> +    minimum: 0
>>> +    maximum: 0xf
>>
>> Same question.
> Same as the reply above.
>>
>>> +
>>> +  mediatek,prohibit-gate-cg:
>>> +    $ref: /schemas/types.yaml#/definitions/flag
>>> +    description:
>>> +      Decide if source clock CG could be disabled when CPU access
>> IP registers.
>>> +      If present, source clock CG could not be disabled.
>>> +      If not present, source clock CG could be disabled.
>>
>>
>> Sounds like you need to describe the clock in "clocks".
> It is not with clock itself, but rather with the bus design that would
> check the 'source_cg' status bit to decide whether to prevent the CPU
> from accessing the IP registers. And there have been no changes to the
> 'source_cg'(already been descirbed before) for MT8196.

I don't understand why do you need this property if it was already
described. Please do not describe things twice.


Best regards,
Krzysztof





[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux