Re: [PATCH v2 0/5] Add support for PCIe3 on x1e80100

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Thu, Sep 19, 2024 at 10:14:06PM +0800, Qiang Yu wrote:
> 
> On 9/14/2024 11:59 AM, Krishna Chaitanya Chundru wrote:
> > Hi qiang,
> > 
> > In next series can you add logic in controller driver
> > to have new ops for this x1e80100 since this hardware
> > has smmuv3 support but currently the ops_1_9_0 ops which
> > is being used has configuring bdf to sid table which will
> > be not present for this devices.
> > 
> Sure, bdf2sid map is not supported and required since we use smmuv3 for
> pcie on x1e80100. Can I add a new ops which is same as ops_1_9_0 basically
> and only config_sid callback is removed. Or add a new flag to determine if
> we need to config bdf2sid map like no_l0s.
> 
> Hi Mani, what do you think about this?
> 

Good question. IMO it is better to add a new ops even though it duplictes the
callbacks. Because the newer platforms are not going to need this bdf2sid map
anyway. But if we add a flag to determine that, then the check will become,

	if (pcie->cfg->ops->config_sid && !pcie->cfg->smmuv3)
		...

And this doesn't look good as both conditions are false for X1E80100 i.e., it
doesn't need bdf2sid mapping and it is also a SMMUv3 platform. Moreover having
two checks here makes it confusing also.

So let's use a new callback. But please mention the IP revision in comments as
like other ops.

- Mani

> Thanks,
> Qiang
> > 
> > - Krishna Chaitanya.
> > 
> > On 9/13/2024 2:07 PM, Qiang Yu wrote:
> > > This series add support for PCIe3 on x1e80100.
> > > 
> > > PCIe3 needs additional set of clocks, regulators and new set of PCIe QMP
> > > PHY configuration compare other PCIe instances on x1e80100. Hence add
> > > required resource configuration and usage for PCIe3.
> > > 
> > > v2->v1:
> > > 1. Squash [PATCH 1/8], [PATCH 2/8],[PATCH 3/8] into one patch and
> > > make the
> > >     indentation consistent.
> > > 2. Put dts patch at the end of the patchset.
> > > 3. Put dt-binding patch at the first of the patchset.
> > > 4. Add a new patch where opp-table is added in dt-binding to avoid dtbs
> > >     checking error.
> > > 5. Remove GCC_PCIE_3_AUX_CLK, RPMH_CXO_CLK, put in
> > > TCSR_PCIE_8L_CLKREF_EN
> > >     as ref.
> > > 6. Remove lane_broadcasting.
> > > 7. Add 64 bit bar, Remove GCC_PCIE_3_PIPE_CLK_SRC,
> > >     GCC_CFG_NOC_PCIE_ANOC_SOUTH_AHB_CLK is changed to
> > >     GCC_CFG_NOC_PCIE_ANOC_NORTH_AHB_CLK.
> > > 8. Add Reviewed-by tag.
> > > 9. Remove [PATCH 7/8], [PATCH 8/8].
> > > 
> > > Qiang Yu (5):
> > >    dt-bindings: phy: qcom,sc8280xp-qmp-pcie-phy: Document the X1E80100
> > >      QMP PCIe PHY Gen4 x8
> > >    dt-bindings: PCI: qcom: Add OPP table for X1E80100
> > >    phy: qcom: qmp: Add phy register and clk setting for x1e80100 PCIe3
> > >    clk: qcom: gcc-x1e80100: Fix halt_check for pipediv2 clocks
> > >    arm64: dts: qcom: x1e80100: Add support for PCIe3 on x1e80100
> > > 
> > >   .../bindings/pci/qcom,pcie-x1e80100.yaml      |   4 +
> > >   .../phy/qcom,sc8280xp-qmp-pcie-phy.yaml       |   3 +
> > >   arch/arm64/boot/dts/qcom/x1e80100.dtsi        | 202 ++++++++++++++++-
> > >   drivers/clk/qcom/gcc-x1e80100.c               |  10 +-
> > >   drivers/phy/qualcomm/phy-qcom-qmp-pcie.c      | 211 ++++++++++++++++++
> > >   .../qualcomm/phy-qcom-qmp-pcs-pcie-v6_30.h    |  25 +++
> > >   drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6_30.h |  19 ++
> > >   7 files changed, 468 insertions(+), 6 deletions(-)
> > >   create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v6_30.h
> > >   create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6_30.h
> > > 

-- 
மணிவண்ணன் சதாசிவம்




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux