From: Emil Renner Berthing <emil.renner.berthing@xxxxxxxxxxxxx> Add bindings for the pin controllers on the T-Head TH1520 RISC-V SoC. Tested-by: Thomas Bonnefille <thomas.bonnefille@xxxxxxxxxxx> Signed-off-by: Emil Renner Berthing <emil.renner.berthing@xxxxxxxxxxxxx> [dfustini: add thead,pad-group to select the pin controller instance] Signed-off-by: Drew Fustini <dfustini@xxxxxxxxxxxxxxx> --- .../bindings/pinctrl/thead,th1520-pinctrl.yaml | 176 +++++++++++++++++++++ MAINTAINERS | 1 + 2 files changed, 177 insertions(+) diff --git a/Documentation/devicetree/bindings/pinctrl/thead,th1520-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/thead,th1520-pinctrl.yaml new file mode 100644 index 000000000000..21f86740a63d --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/thead,th1520-pinctrl.yaml @@ -0,0 +1,176 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/thead,th1520-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: T-Head TH1520 SoC pin controller + +maintainers: + - Emil Renner Berthing <emil.renner.berthing@xxxxxxxxxxxxx> + +description: | + Pinmux and pinconf controller in the T-Head TH1520 RISC-V SoC. + + The TH1520 has 3 groups of pads each controlled from different memory ranges. + Confusingly the memory ranges are named + PADCTRL_AOSYS -> PAD Group 1 + PADCTRL1_APSYS -> PAD Group 2 + PADCTRL0_APSYS -> PAD Group 3 + + Each pad can be muxed individually to up to 6 different functions. For most + pads only a few of those 6 configurations are valid though, and a few pads in + group 1 does not support muxing at all. + + Pinconf is fairly regular except for a few pads in group 1 that either can't + be configured or has some special functions. The rest have configurable drive + strength, input enable, schmitt trigger, slew rate, pull-up and pull-down in + addition to a special strong pull up. + + Certain pads in group 1 can be muxed to AUDIO_PA0 - AUDIO_PA30 functions and + are then meant to be used by the audio co-processor. Each such pad can then + be further muxed to either audio GPIO or one of 4 functions such as UART, I2C + and I2S. If the audio pad is muxed to one of the 4 functions then pinconf is + also configured in different registers. All of this is done from a different + AUDIO_IOCTRL memory range and is left to the audio co-processor for now. + +properties: + compatible: + enum: + - thead,th1520-pinctrl + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + thead,pad-group: + description: | + Select the pad group that is associated with the pin controller instance. + + Base Address Name Group + 0xFF_FFF4_A000 PADCTRL_AOSYS 1 + 0xFF_E7F3_C000 PADCTRL1_APSYS 2 + 0xFF_EC00_7000 PADCTRL0_APSYS 3 + + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [1, 2, 3] + +required: + - compatible + - reg + - clocks + +patternProperties: + '-[0-9]+$': + type: object + additionalProperties: false + + patternProperties: + '-pins$': + type: object + allOf: + - $ref: /schemas/pinctrl/pincfg-node.yaml# + - $ref: /schemas/pinctrl/pinmux-node.yaml# + + additionalProperties: false + + description: + A pinctrl node should contain at least one subnode describing one + or more pads and their associated pinmux and pinconf settings. + + properties: + pins: + description: List of pads that properties in the node apply to. + + function: + enum: [ gpio, pwm, uart, ir, i2c, spi, qspi, sdio, audio, i2s, + gmac0, gmac1, dpu0, dpu1, isp, hdmi, bootsel, debug, + clock, jtag, iso7816, efuse, reset ] + description: The mux function to select for the given pins. + + bias-disable: true + + bias-pull-up: + oneOf: + - type: boolean + description: Enable the regular 48kOhm pull-up + - enum: [ 2100, 48000 ] + description: Enable the strong 2.1kOhm pull-up or regular 48kOhm pull-up + + bias-pull-down: + oneOf: + - type: boolean + - const: 44000 + description: Enable the regular 44kOhm pull-down + + drive-strength: + enum: [ 1, 2, 3, 5, 7, 8, 10, 12, 13, 15, 16, 18, 20, 21, 23, 25 ] + description: Drive strength in mA + + input-enable: true + + input-disable: true + + input-schmitt-enable: true + + input-schmitt-disable: true + + slew-rate: + maximum: 1 + + required: + - pins + +additionalProperties: false + +examples: + - | + padctrl0_apsys: pinctrl@ec007000 { + compatible = "thead,th1520-pinctrl"; + reg = <0xec007000 0x1000>; + clocks = <&apb_clk>; + thead,pad-group = <3>; + + uart0_pins: uart0-0 { + tx-pins { + pins = "UART0_TXD"; + function = "uart"; + bias-disable; + drive-strength = <3>; + input-disable; + input-schmitt-disable; + slew-rate = <0>; + }; + + rx-pins { + pins = "UART0_RXD"; + function = "uart"; + bias-disable; + drive-strength = <1>; + input-enable; + input-schmitt-enable; + slew-rate = <0>; + }; + }; + }; + + padctrl1_apsys: pinctrl@e7f3c000 { + compatible = "thead,th1520-pinctrl"; + reg = <0xe7f3c000 0x1000>; + clocks = <&apb_clk>; + thead,pad-group = <2>; + + i2c5_pins: i2c5-0 { + i2c-pins { + pins = "QSPI1_CSN0", /* I2C5_SCL */ + "QSPI1_D0_MOSI"; /* I2C5_SDA */ + function = "i2c"; + bias-pull-up = <2100>; + drive-strength = <7>; + input-enable; + input-schmitt-enable; + slew-rate = <0>; + }; + }; + }; diff --git a/MAINTAINERS b/MAINTAINERS index 878dcd23b331..a73953c0f080 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -19700,6 +19700,7 @@ L: linux-riscv@xxxxxxxxxxxxxxxxxxx S: Maintained T: git https://github.com/pdp7/linux.git F: Documentation/devicetree/bindings/clock/thead,th1520-clk-ap.yaml +F: Documentation/devicetree/bindings/pinctrl/thead,th1520-pinctrl.yaml F: arch/riscv/boot/dts/thead/ F: drivers/clk/thead/clk-th1520-ap.c F: include/dt-bindings/clock/thead,th1520-clk-ap.h -- 2.34.1
