On Tue, Sep 10, 2024 at 03:14:50PM -0400, Frank Li wrote:
> On Tue, Sep 10, 2024 at 03:03:39PM +0800, Xu Yang wrote:
> > This board has one Type-C port which has USB3 capability. This will
> > add typec nodes and enable usb3 node.
> >
> > Signed-off-by: Xu Yang <xu.yang_2@xxxxxxx>
> >
> > ---
> > Changes in v2:
> > - no changes
> > Changes in v3:
> > - no changes
> > Changes in v4:
> > - no changes
> > ---
> > .../boot/dts/freescale/imx95-19x19-evk.dts | 81 +++++++++++++++++++
> > 1 file changed, 81 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts b/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts
> > index d14a54ab4fd4..46a9cd3d4403 100644
> > --- a/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts
> > +++ b/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts
> > @@ -5,6 +5,7 @@
> >
> > /dts-v1/;
> >
> > +#include <dt-bindings/usb/pd.h>
> > #include "imx95.dtsi"
> >
> > / {
> > @@ -99,6 +100,48 @@ i2c7_pcal6524: i2c7-gpio@22 {
> > interrupt-parent = <&gpio5>;
> > interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
> > };
> > +
> > + ptn5110: tcpc@50 {
> > + compatible = "nxp,ptn5110", "tcpci";
> > + reg = <0x50>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_typec>;
> > + interrupt-parent = <&gpio5>;
> > + interrupts = <14 IRQ_TYPE_LEVEL_LOW>;
> > +
> > + typec_con: connector {
> > + compatible = "usb-c-connector";
> > + label = "USB-C";
> > + power-role = "dual";
> > + data-role = "dual";
> > + try-power-role = "sink";
> > + source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
> > + sink-pdos = <PDO_FIXED(5000, 0, PDO_FIXED_USB_COMM)>;
> > + op-sink-microwatt = <0>;
> > + self-powered;
> > +
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + port@0 {
> > + reg = <0>;
> > +
> > + typec_con_hs: endpoint {
> > + remote-endpoint = <&usb3_data_hs>;
> > + };
> > + };
> > +
> > + port@1 {
> > + reg = <1>;
> > +
> > + typec_con_ss: endpoint {
> > + remote-endpoint = <&usb3_data_ss>;
> > + };
> > + };
> > + };
> > + };
> > + };
> > };
> >
> > &lpuart1 {
> > @@ -128,6 +171,38 @@ &pcie1 {
> > status = "okay";
> > };
> >
> > +&usb3 {
> > + status = "okay";
> > +};
> > +
> > +&usb3_phy {
> > + status = "okay";
> > +
> > + port {
> > + usb3_data_ss: endpoint {
> > + remote-endpoint = <&typec_con_ss>;
> > + };
> > + };
> > +};
>
> Please keep node name alphabet order
> usb3_phy should be after usb3_dwc3.
Okay. Will fix the order.
Thanks,
Xu Yang
