Hi Delphine CC Chiu, Thanks for the patch. > -----Original Message----- > From: Delphine CC Chiu <Delphine_CC_Chiu@xxxxxxxxxx> > Sent: Friday, September 6, 2024 7:14 AM > Subject: [PATCH v6 1/3] hwmon: (isl28022) new driver for ISL28022 power monitor > > From: Carsten Spieß <mail@xxxxxxxxxxxxxxxxx> > > Driver for Renesas ISL28022 power monitor with I2C interface. > The device monitors voltage, current via shunt resistor and calculated power. > > Signed-off-by: Carsten Spieß <mail@xxxxxxxxxxxxxxxxx> It is missing your SoB. > --- > Documentation/hwmon/index.rst | 1 + > Documentation/hwmon/isl28022.rst | 63 +++++ > MAINTAINERS | 7 + > drivers/hwmon/Kconfig | 11 + > drivers/hwmon/Makefile | 1 + > drivers/hwmon/isl28022.c | 471 +++++++++++++++++++++++++++++++ > 6 files changed, 554 insertions(+) > create mode 100644 Documentation/hwmon/isl28022.rst create mode 100644 drivers/hwmon/isl28022.c > > diff --git a/Documentation/hwmon/index.rst b/Documentation/hwmon/index.rst index > 913c11390a45..ba297c43d902 100644 > --- a/Documentation/hwmon/index.rst > +++ b/Documentation/hwmon/index.rst > @@ -96,6 +96,7 @@ Hardware Monitoring Kernel Drivers > ir35221 > ir38064 > ir36021 > + isl28022 > isl68137 > it87 > jc42 > diff --git a/Documentation/hwmon/isl28022.rst b/Documentation/hwmon/isl28022.rst > new file mode 100644 > index 000000000000..8d4422a2dacd > --- /dev/null > +++ b/Documentation/hwmon/isl28022.rst > @@ -0,0 +1,63 @@ > +.. SPDX-License-Identifier: GPL-2.0-or-later > + > +Kernel driver isl28022 > +====================== > + > +Supported chips: > + > + * Renesas ISL28022 > + > + Prefix: 'isl28022' > + > + Addresses scanned: none > + > + Datasheet: Publicly available at the Renesas website > + > + https://www.renesas.com/us/en/www/doc/datasheet/isl28022.pdf > + > +Author: > + Carsten Spieß <mail@xxxxxxxxxxxxxxxxx> > + > +Description > +----------- > + > +The ISL28022 is a power monitor with I2C interface. The device monitors > +voltage, current via shunt resistor and calculated power. > + > +Usage Notes > +----------- > + > +This driver does not auto-detect devices. You will have to instantiate > +the device explicitly. Please see > +Documentation/i2c/instantiating-devices.rst for details. > + > +The shunt value in micro-ohms, shunt voltage range and averaging can be > +set with device properties. > +Please refer to the > +Documentation/devicetree/bindings/hwmon/isl,isl28022.yaml > +for bindings if the device tree is used. > + > +The driver supports only shunt and bus continuous ADC mode at 15bit resolution. > +Averaging can be set from 1 to 128 samples (power of 2) on both channels. > +Shunt voltage range of 40, 80, 160 or 320mV is allowed The bus voltage > +range is 60V fixed. > + > +Sysfs entries > +------------- > + > +The following attributes are supported. All attributes are read-only. > + > +======================= ======================================================= > +in0_input bus voltage (milli Volt) > + > +curr1_input current (milli Ampere) > +power1_input power (micro Watt) > +======================= > +======================================================= > + > +Debugfs entries > +--------------- > + > +The following attributes are supported. All attributes are read-only. > + > +======================= ======================================================= > +shunt_voltage shunt voltage (micro Volt) > +======================= > +======================================================= > diff --git a/MAINTAINERS b/MAINTAINERS > index fe83ba7194ea..d39199ed51da 100644 > --- a/MAINTAINERS > +++ b/MAINTAINERS > @@ -11932,6 +11932,13 @@ F: drivers/isdn/Makefile > F: drivers/isdn/hardware/ > F: drivers/isdn/mISDN/ > > +ISL28022 HARDWARE MONITORING DRIVER > +M: Carsten Spieß <mail@xxxxxxxxxxxxxxxxx> > +L: linux-hwmon@xxxxxxxxxxxxxxx > +S: Maintained > +F: Documentation/hwmon/isl28022.rst > +F: drivers/hwmon/isl28022.c > + > ISOFS FILESYSTEM > M: Jan Kara <jack@xxxxxxx> > L: linux-fsdevel@xxxxxxxxxxxxxxx > diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig index b60fe2e58ad6..adbbbb128afc 100644 > --- a/drivers/hwmon/Kconfig > +++ b/drivers/hwmon/Kconfig > @@ -853,6 +853,17 @@ config SENSORS_CORETEMP > sensor inside your CPU. Most of the family 6 CPUs > are supported. Check Documentation/hwmon/coretemp.rst for details. > > +config SENSORS_ISL28022 > + tristate "Renesas ISL28022" > + depends on I2C > + select REGMAP_I2C > + help > + If you say yes here you get support for ISL28022 power monitor. > + Check Documentation/hwmon/isl28022.rst for details. > + > + This driver can also be built as a module. If so, the module > + will be called isl28022. > + > config SENSORS_IT87 > tristate "ITE IT87xx and compatibles" > depends on HAS_IOPORT > diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile index b1c7056c37db..51132b2b2c07 100644 > --- a/drivers/hwmon/Makefile > +++ b/drivers/hwmon/Makefile > @@ -103,6 +103,7 @@ obj-$(CONFIG_SENSORS_INA2XX) += ina2xx.o > obj-$(CONFIG_SENSORS_INA238) += ina238.o > obj-$(CONFIG_SENSORS_INA3221) += ina3221.o > obj-$(CONFIG_SENSORS_INTEL_M10_BMC_HWMON) += intel-m10-bmc-hwmon.o > +obj-$(CONFIG_SENSORS_ISL28022) += isl28022.o > obj-$(CONFIG_SENSORS_IT87) += it87.o > obj-$(CONFIG_SENSORS_JC42) += jc42.o > obj-$(CONFIG_SENSORS_K8TEMP) += k8temp.o > diff --git a/drivers/hwmon/isl28022.c b/drivers/hwmon/isl28022.c new file mode 100644 index > 000000000000..f0494c3bd483 > --- /dev/null > +++ b/drivers/hwmon/isl28022.c > @@ -0,0 +1,471 @@ > +// SPDX-License-Identifier: GPL-2.0-or-later > +/* > + * isl28022.c - driver for Renesas ISL28022 power monitor chip > +monitoring > + * > + * Copyright (c) 2023 Carsten Spieß <mail@xxxxxxxxxxxxxxxxx> */ > + > +#include <linux/debugfs.h> > +#include <linux/err.h> > +#include <linux/hwmon.h> > +#include <linux/i2c.h> > +#include <linux/module.h> > +#include <linux/regmap.h> > +#include <linux/slab.h> Do you need slab.h ?? > + > +/* ISL28022 registers */ > +#define ISL28022_REG_CONFIG 0x00 > +#define ISL28022_REG_SHUNT 0x01 > +#define ISL28022_REG_BUS 0x02 > +#define ISL28022_REG_POWER 0x03 > +#define ISL28022_REG_CURRENT 0x04 > +#define ISL28022_REG_CALIB 0x05 > +#define ISL28022_REG_SHUNT_THR 0x06 > +#define ISL28022_REG_BUS_THR 0x07 > +#define ISL28022_REG_INT 0x08 > +#define ISL28022_REG_AUX 0x09 > +#define ISL28022_REG_MAX ISL28022_REG_AUX > + > +/* ISL28022 config flags */ > +/* mode flags */ > +#define ISL28022_MODE_SHIFT 0 > +#define ISL28022_MODE_MASK 0x0007 > + > +#define ISL28022_MODE_PWR_DOWN 0x0 > +#define ISL28022_MODE_TRG_S 0x1 > +#define ISL28022_MODE_TRG_B 0x2 > +#define ISL28022_MODE_TRG_SB 0x3 > +#define ISL28022_MODE_ADC_OFF 0x4 > +#define ISL28022_MODE_CONT_S 0x5 > +#define ISL28022_MODE_CONT_B 0x6 > +#define ISL28022_MODE_CONT_SB 0x7 > + > +/* shunt ADC settings */ > +#define ISL28022_SADC_SHIFT 3 > +#define ISL28022_SADC_MASK 0x0078 > + > +#define ISL28022_BADC_SHIFT 7 > +#define ISL28022_BADC_MASK 0x0780 > + > +#define ISL28022_ADC_12 0x0 /* 12 bit ADC */ > +#define ISL28022_ADC_13 0x1 /* 13 bit ADC */ > +#define ISL28022_ADC_14 0x2 /* 14 bit ADC */ > +#define ISL28022_ADC_15 0x3 /* 15 bit ADC */ > +#define ISL28022_ADC_15_1 0x8 /* 15 bit ADC, 1 sample */ > +#define ISL28022_ADC_15_2 0x9 /* 15 bit ADC, 2 samples */ > +#define ISL28022_ADC_15_4 0xA /* 15 bit ADC, 4 samples */ > +#define ISL28022_ADC_15_8 0xB /* 15 bit ADC, 8 samples */ > +#define ISL28022_ADC_15_16 0xC /* 15 bit ADC, 16 samples */ > +#define ISL28022_ADC_15_32 0xD /* 15 bit ADC, 32 samples */ > +#define ISL28022_ADC_15_64 0xE /* 15 bit ADC, 64 samples */ > +#define ISL28022_ADC_15_128 0xF /* 15 bit ADC, 128 samples */ > + > +/* shunt voltage range */ > +#define ISL28022_PG_SHIFT 11 > +#define ISL28022_PG_MASK 0x1800 > + > +#define ISL28022_PG_40 0x0 /* +/-40 mV */ > +#define ISL28022_PG_80 0x1 /* +/-80 mV */ > +#define ISL28022_PG_160 0x2 /* +/-160 mV */ > +#define ISL28022_PG_320 0x3 /* +/-3200 mV */ > + > +/* bus voltage range */ > +#define ISL28022_BRNG_SHIFT 13 > +#define ISL28022_BRNG_MASK 0x6000 > + > +#define ISL28022_BRNG_16 0x0 /* 16 V */ > +#define ISL28022_BRNG_32 0x1 /* 32 V */ > +#define ISL28022_BRNG_60 0x3 /* 60 V */ > + > +/* reset */ > +#define ISL28022_RESET 0x8000 > + > +struct isl28022_data { > + struct regmap *regmap; > + u32 shunt; > + u32 gain; > + u32 average; > + u16 config; > + u16 calib; > +}; > + > +static int isl28022_read(struct device *dev, enum hwmon_sensor_types type, > + u32 attr, int channel, long *val) > +{ > + struct isl28022_data *data = dev_get_drvdata(dev); > + unsigned int regval; > + int err; > + > + switch (type) { > + case hwmon_in: > + switch (attr) { > + case hwmon_in_input: > + err = regmap_read(data->regmap, > + ISL28022_REG_BUS, ®val); > + if (err < 0) > + return err; > + /* driver supports only 60V mode (BRNG 11) */ > + *val = (long)(((u16)regval) & 0xFFFC); > + break; > + default: > + return -EINVAL; > + } > + break; > + case hwmon_curr: > + switch (attr) { > + case hwmon_curr_input: > + err = regmap_read(data->regmap, > + ISL28022_REG_CURRENT, ®val); > + if (err < 0) > + return err; > + *val = ((long)regval * 1250L * (long)data->gain) / > + (long)data->shunt; > + break; > + default: > + return -EINVAL; > + } > + break; > + case hwmon_power: > + switch (attr) { > + case hwmon_power_input: > + err = regmap_read(data->regmap, > + ISL28022_REG_POWER, ®val); > + if (err < 0) > + return err; > + *val = ((51200000L * ((long)data->gain)) / > + (long)data->shunt) * (long)regval; > + break; > + default: > + return -EINVAL; > + } > + break; > + default: > + return -EINVAL; > + } > + > + return 0; > +} > + > +static umode_t isl28022_is_visible(const void *data, enum hwmon_sensor_types type, > + u32 attr, int channel) > +{ > + switch (type) { > + case hwmon_in: > + switch (attr) { > + case hwmon_in_input: > + return 0444; > + default: > + break; > + } > + break; > + case hwmon_curr: > + switch (attr) { > + case hwmon_curr_input: > + return 0444; > + default: > + break; > + } > + break; > + case hwmon_power: > + switch (attr) { > + case hwmon_power_input: > + return 0444; > + default: > + break; > + } > + break; > + default: > + break; > + } > + return 0; > +} > + > +static const struct hwmon_channel_info *isl28022_info[] = { > + HWMON_CHANNEL_INFO(in, > + HWMON_I_INPUT), /* channel 0: bus voltage (mV) */ > + HWMON_CHANNEL_INFO(curr, > + HWMON_C_INPUT), /* channel 1: current (mA) */ > + HWMON_CHANNEL_INFO(power, > + HWMON_P_INPUT), /* channel 1: power (µW) */ > + NULL > +}; > + > +static const struct hwmon_ops isl28022_hwmon_ops = { > + .is_visible = isl28022_is_visible, > + .read = isl28022_read, > +}; > + > +static const struct hwmon_chip_info isl28022_chip_info = { > + .ops = &isl28022_hwmon_ops, > + .info = isl28022_info, > +}; > + > +static bool isl28022_is_writeable_reg(struct device *dev, unsigned int > +reg) { > + switch (reg) { > + case ISL28022_REG_CONFIG: > + case ISL28022_REG_CALIB: > + case ISL28022_REG_SHUNT_THR: > + case ISL28022_REG_BUS_THR: > + case ISL28022_REG_INT: > + case ISL28022_REG_AUX: > + return true; > + } > + > + return false; > +} > + > +static bool isl28022_is_volatile_reg(struct device *dev, unsigned int > +reg) { > + switch (reg) { > + case ISL28022_REG_CONFIG: > + case ISL28022_REG_SHUNT: > + case ISL28022_REG_BUS: > + case ISL28022_REG_POWER: > + case ISL28022_REG_CURRENT: > + case ISL28022_REG_INT: > + case ISL28022_REG_AUX: > + return true; > + } > + return true; > +} > + > +static const struct regmap_config isl28022_regmap_config = { > + .reg_bits = 8, > + .val_bits = 16, > + .max_register = ISL28022_REG_MAX, > + .writeable_reg = isl28022_is_writeable_reg, > + .volatile_reg = isl28022_is_volatile_reg, > + .val_format_endian = REGMAP_ENDIAN_BIG, > + .cache_type = REGCACHE_RBTREE, > + .use_single_read = true, > + .use_single_write = true, > +}; > + > +static const struct i2c_device_id isl28022_ids[] = { > + { "isl28022", 0}, > + { /* LIST END */ } > +}; > +MODULE_DEVICE_TABLE(i2c, isl28022_ids); Move this table near to the user. > + > +static int shunt_voltage_show(struct seq_file *seqf, void *unused) { > + struct isl28022_data *data = seqf->private; > + unsigned int regval; > + int err; > + > + err = regmap_read(data->regmap, > + ISL28022_REG_SHUNT, ®val); > + if (err) > + return err; > + > + /* print shunt voltage in micro volt */ > + seq_printf(seqf, "%d\n", regval * 10); > + > + return 0; > +} > +DEFINE_SHOW_ATTRIBUTE(shunt_voltage); > + > +static struct dentry *isl28022_debugfs_root; > + > +static void isl28022_debugfs_remove(void *res) { > + debugfs_remove_recursive(res); > +} > + > +static void isl28022_debugfs_init(struct i2c_client *client, struct > +isl28022_data *data) { > + char name[16]; > + struct dentry *debugfs; > + > + scnprintf(name, sizeof(name), "%d-%04hx", client->adapter->nr, > +client->addr); > + > + debugfs = debugfs_create_dir(name, isl28022_debugfs_root); > + debugfs_create_file("shunt_voltage", 0444, debugfs, data, > +&shunt_voltage_fops); > + > + devm_add_action_or_reset(&client->dev, isl28022_debugfs_remove, > +debugfs); } > + > +/* > + * read property values and make consistency checks. > + * > + * following values for shunt range and resistor are allowed: > + * 40 mV -> gain 1, shunt min. 800 micro ohms > + * 80 mV -> gain 2, shunt min. 1600 micro ohms > + * 160 mV -> gain 4, shunt min. 3200 micro ohms > + * 320 mV -> gain 8, shunt min. 6400 micro ohms */ static int > +isl28022_read_properties(struct device *dev, struct isl28022_data > +*data) { > + u32 val; > + int err; > + > + err = device_property_read_u32(dev, "shunt-resistor-micro-ohms", &val); > + if (err == -EINVAL) > + val = 10000; > + else if (err < 0) > + return err; > + data->shunt = val; > + > + err = device_property_read_u32(dev, "renesas,shunt-range-microvolt", &val); > + if (err == -EINVAL) > + val = 320000; > + else if (err < 0) > + return err; > + > + switch (val) { > + case 40000: > + data->gain = 1; > + if (data->shunt < 800) > + goto shunt_invalid; > + break; > + case 80000: > + data->gain = 2; > + if (data->shunt < 1600) > + goto shunt_invalid; > + break; > + case 160000: > + data->gain = 4; > + if (data->shunt < 3200) > + goto shunt_invalid; > + break; > + case 320000: > + data->gain = 8; > + if (data->shunt < 6400) > + goto shunt_invalid; > + break; > + default: > + dev_err(dev, "renesas,shunt-range-microvolt invalid value %d\n", val); Use dev_err_probe() > + return -EINVAL; > + } > + > + err = device_property_read_u32(dev, "renesas,average-samples", &val); > + if (err == -EINVAL) > + val = 1; > + else if (err < 0) > + return err; > + if (val > 128 || hweight32(val) != 1) { > + dev_err(dev, "renesas,average-samples invalid value %d\n", val); Use dev_err_probe() > + return -EINVAL; > + } > + data->average = val; > + > + return 0; > + > +shunt_invalid: > + dev_err(dev, "renesas,shunt-resistor-microvolt invalid value %d\n", data->shunt); Use dev_err_probe() Cheers, Biju > + return -EINVAL; > +} > + > +/* > + * write configuration and calibration registers > + * > + * The driver supports only shunt and bus continuous ADC mode at 15bit > +resolution > + * with averaging from 1 to 128 samples (pow of 2) on both channels. > + * Shunt voltage gain 1,2,4 or 8 is allowed. > + * The bus voltage range is 60V fixed. > + */ > +static int isl28022_config(struct isl28022_data *data) { > + int err; > + > + data->config = (ISL28022_MODE_CONT_SB << ISL28022_MODE_SHIFT) | > + (ISL28022_BRNG_60 << ISL28022_BRNG_SHIFT) | > + (__ffs(data->gain) << ISL28022_PG_SHIFT) | > + ((ISL28022_ADC_15_1 + __ffs(data->average)) << ISL28022_SADC_SHIFT) | > + ((ISL28022_ADC_15_1 + __ffs(data->average)) << ISL28022_BADC_SHIFT); > + > + data->calib = data->shunt ? 0x8000 / data->gain : 0; > + > + err = regmap_write(data->regmap, ISL28022_REG_CONFIG, data->config); > + if (err < 0) > + return err; > + > + err = regmap_write(data->regmap, ISL28022_REG_CALIB, data->calib); > + if (err < 0) > + return err; > + > + return 0; > +} > + > +static int isl28022_probe(struct i2c_client *client) { > + struct device *dev = &client->dev; > + struct device *hwmon_dev; > + struct isl28022_data *data; > + int err; > + > + if (!i2c_check_functionality(client->adapter, > + I2C_FUNC_SMBUS_BYTE_DATA | > + I2C_FUNC_SMBUS_WORD_DATA)) > + return -ENODEV; > + > + data = devm_kzalloc(dev, sizeof(struct isl28022_data), GFP_KERNEL); > + if (!data) > + return -ENOMEM; > + > + err = isl28022_read_properties(dev, data); > + if (err) > + return err; > + > + data->regmap = devm_regmap_init_i2c(client, &isl28022_regmap_config); > + if (IS_ERR(data->regmap)) > + return PTR_ERR(data->regmap); > + > + err = isl28022_config(data); > + if (err) > + return err; > + > + isl28022_debugfs_init(client, data); > + > + hwmon_dev = devm_hwmon_device_register_with_info(dev, "isl28022_hwmon", > + data, &isl28022_chip_info, NULL); > + if (IS_ERR(hwmon_dev)) > + return PTR_ERR(hwmon_dev); > + > + dev_info(dev, "%s: sensor '%s'\n", dev_name(hwmon_dev), client->name); > + return 0; > +} > + > +static const struct of_device_id __maybe_unused isl28022_of_match[] = { > + { .compatible = "renesas,isl28022"}, > + { /* LIST END */ } > +}; > +MODULE_DEVICE_TABLE(of, isl28022_of_match); > + > +static struct i2c_driver isl28022_driver = { > + .class = I2C_CLASS_HWMON, > + .driver = { > + .name = "isl28022", > + }, > + .probe_new = isl28022_probe, > + .id_table = isl28022_ids, > +}; > + > +static int __init > +isl28022_init(void) > +{ > + int err; > + > + isl28022_debugfs_root = debugfs_create_dir("isl28022", NULL); > + err = i2c_add_driver(&isl28022_driver); > + if (!err) > + return 0; > + > + debugfs_remove_recursive(isl28022_debugfs_root); > + return err; > +} > + > +static void __exit > +isl28022_exit(void) > +{ > + i2c_del_driver(&isl28022_driver); > + debugfs_remove_recursive(isl28022_debugfs_root); > +} > + > +module_init(isl28022_init); > +module_exit(isl28022_exit); > + > +MODULE_AUTHOR("Carsten Spieß <mail@xxxxxxxxxxxxxxxxx>"); > +MODULE_DESCRIPTION("ISL28022 driver"); > +MODULE_LICENSE("GPL"); > -- > 2.25.1 >