Hi Philipp,
2015-03-13 9:50 GMT+01:00 Philipp Zabel <p.zabel@xxxxxxxxxxxxxx>:
> Hi Maxime,
>
> Am Donnerstag, den 12.03.2015, 22:55 +0100 schrieb Maxime Coquelin:
>> From: Maxime Coquelin <mcoquelin.stm32@xxxxxxxxx>
>>
>> This adds documentation of device tree bindings for the
>> STM32 reset controller.
>>
>> Signed-off-by: Maxime Coquelin <mcoquelin.stm32@xxxxxxxxx>
>> ---
>> .../devicetree/bindings/reset/st,stm32-rcc.txt | 102 +++++++++++++++++++++
>> 1 file changed, 102 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/reset/st,stm32-rcc.txt
>>
>> diff --git a/Documentation/devicetree/bindings/reset/st,stm32-rcc.txt b/Documentation/devicetree/bindings/reset/st,stm32-rcc.txt
>> new file mode 100644
>> index 0000000..962f961
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/reset/st,stm32-rcc.txt
>> @@ -0,0 +1,102 @@
>> +STMicroelectronics STM32 Peripheral Reset Controller
>> +====================================================
>> +
>> +The RCC IP is both a reset and a clock controller. This documentation only
>> +document the reset part.
>> +
>> +Please also refer to reset.txt in this directory for common reset
>> +controller binding usage.
>> +
>> +Required properties:
>> +- compatible: Should be "st,stm32-rcc"
>> +- reg: should be register base and length as documented in the
>> + datasheet
>> +- #reset-cells: 1, see below
>> +
>> +example:
>> +
>> +rcc: reset@40023800 {
>> + #reset-cells = <1>;
>> + compatible = "st,stm32-rcc";
>> + reg = <0x40023800 0x400>;
>> +};
>> +
>> +Specifying softreset control of devices
>> +=======================================
>> +
>> +Device nodes should specify the reset channel required in their "resets"
>> +property, containing a phandle to the reset device node and an index specifying
>> +which channel to use.
>
> Using a single value as index is ok, but it should be documented how
> this corresponds to the register and bit offsets in the reference
> manual.
> Maybe add a comment that the index is in fact the register offset / 4 *
> 32 + bit offset in that register and that not all registers are
> dedicated to the rest controller? Otherwise it is confusing (to me at
> least) that the indices start at some arbitrary value.
I agree to better document it. Are you ok with:
The index is the bit number within the RCC registers bank, starting from RCC
base address.
It is calculated as: index = register_offset / 4 * 32 + bit_offset.
Where bit_offset is the bit offset within the register.
For example, for CRC reset:
crc = AHB1RSTR_offset / 4 * 32 + CRCRST_bit_offset = 0x10 / 4 * 32 + 12 = 140
>
>> +example:
>> +
>> + timer2 {
>> + resets = <&rcc 256>;
>> + };
>> +
>> +List of indexes for STM32F429:
>
> "List of valid indices", to point out that any other index is invalid?
Right, it will be changed in v4.
>
>> + - gpioa: 128
>
> I had to look at the RM0090 Reference manual V8.0, Chapter 6, "Reset and
> clock control for STM32F42xx and STM32F43xxx (RCC)" to see that the
> reset registers indeed start at 0x10 (RCC_AHB1RSTR), ...
>
>> + - gpiob: 129
>> + - gpioc: 130
>> + - gpiod: 131
>> + - gpioe: 132
>> + - gpiof: 133
>> + - gpiog: 134
>> + - gpioh: 135
>> + - gpioi: 136
>> + - gpioj: 137
>> + - gpiok: 138
>> + - crc: 140
>> + - dma1: 149
>> + - dma2: 150
>> + - dma2d: 151
>> + - ethmac: 153
>> + - otghs: 157
>> + - dcmi: 160
>> + - cryp: 164
>> + - hash: 165
>> + - rng: 166
>> + - otgfs: 167
>> + - fmc: 192
>> + - tim2: 256
>> + - tim3: 257
>> + - tim4: 258
>> + - tim5: 259
>> + - tim6: 260
>> + - tim7: 261
>> + - tim12: 262
>> + - tim13: 263
>> + - tim14: 264
>> + - wwdg: 267
>> + - spi2: 270
>> + - spi3: 271
>> + - uart2: 273
>> + - uart3: 274
>> + - uart4: 275
>> + - uart5: 276
>> + - i2c1: 277
>> + - i2c2: 278
>> + - i2c3: 279
>> + - can1: 281
>> + - can2: 282
>> + - pwr: 284
>> + - dac: 285
>> + - uart7: 286
>> + - uart8: 287
>> + - tim1: 288
>> + - tim8: 289
>> + - usart1: 292
>> + - usart6: 293
>> + - adc: 296
>> + - sdio: 299
>> + - spi1: 300
>> + - spi4: 301
>> + - syscfg: 302
>> + - tim9: 304
>> + - tim10: 305
>> + - tim11: 306
>> + - spi5: 308
>> + - spi6: 309
>> + - sai1: 310
>> + - ltdc: 31
>
> That last one should say "ltdc: 314", right?
Thanks for catching this!
Just fixed it, it will be in v4.
Kind regards,
Maxime
>
> regards
> Philipp
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
