The driver will support the AD7606C-16 and AD7606C-18. This change adds the compatible strings for these devices. The AD7606C-16,18 channels also support these (individually configurable) types of channels: - bipolar single-ended - unipolar single-ended - bipolar differential Signed-off-by: Alexandru Ardelean <aardelean@xxxxxxxxxxxx> --- .../bindings/iio/adc/adi,ad7606.yaml | 108 ++++++++++++++++++ 1 file changed, 108 insertions(+) diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml index 69408cae3db9..f6fbc760d25d 100644 --- a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml @@ -14,6 +14,8 @@ description: | https://www.analog.com/media/en/technical-documentation/data-sheets/AD7605-4.pdf https://www.analog.com/media/en/technical-documentation/data-sheets/ad7606_7606-6_7606-4.pdf https://www.analog.com/media/en/technical-documentation/data-sheets/AD7606B.pdf + https://www.analog.com/media/en/technical-documentation/data-sheets/ad7606c-16.pdf + https://www.analog.com/media/en/technical-documentation/data-sheets/ad7606c-18.pdf https://www.analog.com/media/en/technical-documentation/data-sheets/AD7616.pdf properties: @@ -24,11 +26,19 @@ properties: - adi,ad7606-6 - adi,ad7606-8 # Referred to as AD7606 (without -8) in the datasheet - adi,ad7606b + - adi,ad7606c-16 + - adi,ad7606c-18 - adi,ad7616 reg: maxItems: 1 + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + spi-cpha: true spi-cpol: true @@ -114,6 +124,45 @@ properties: assumed that the pins are hardwired to VDD. type: boolean +patternProperties: + "^channel@([1-8])$": + type: object + $ref: adc.yaml + unevaluatedProperties: false + + properties: + reg: + description: + The channel number, as specified in the datasheet (from 1 to 8). + minimum: 1 + maximum: 8 + + diff-channels: + description: + Each channel can be configured as a differential bipolar channel. + The ADC uses the same positive and negative inputs for this. + This property must be specified as 'reg' (or the channel number) for + both positive and negative inputs (i.e. diff-channels = <reg reg>). + items: + minimum: 1 + maximum: 8 + + bipolar: + description: + Each channel can be configured as a unipolar or bipolar single-ended. + When this property is not specified, it's unipolar, so the ADC will + have only the positive input wired. + For this ADC the 'diff-channels' & 'bipolar' properties are mutually + exclusive. + + oneOf: + - required: + - reg + - diff-channels + - required: + - reg + - bipolar + required: - compatible - reg @@ -170,6 +219,17 @@ allOf: adi,conversion-start-gpios: maxItems: 1 + - if: + not: + properties: + compatible: + enum: + - adi,ad7606c-16 + - adi,ad7606c-18 + then: + patternProperties: + "^channel@[1-8]+$": false + unevaluatedProperties: false examples: @@ -202,4 +262,52 @@ examples: standby-gpios = <&gpio 24 GPIO_ACTIVE_LOW>; }; }; + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + spi { + #address-cells = <1>; + #size-cells = <0>; + + adc@0 { + compatible = "adi,ad7606c-18"; + reg = <0>; + + #address-cells = <1>; + #size-cells = <0>; + + spi-max-frequency = <1000000>; + spi-cpol; + spi-cpha; + + avcc-supply = <&adc_vref>; + vdrive-supply = <&vdd_supply>; + + interrupts = <25 IRQ_TYPE_EDGE_FALLING>; + interrupt-parent = <&gpio>; + + adi,conversion-start-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio 27 GPIO_ACTIVE_HIGH>; + adi,first-data-gpios = <&gpio 22 GPIO_ACTIVE_HIGH>; + standby-gpios = <&gpio 24 GPIO_ACTIVE_LOW>; + + adi,sw-mode; + + channel@1 { + reg = <1>; + diff-channels = <1 1>; + }; + + channel@3 { + reg = <3>; + bipolar; + }; + + channel@8 { + reg = <8>; + diff-channels = <8 8>; + }; + + }; + }; ... -- 2.46.0
