From: Bartosz Golaszewski <bartosz.golaszewski@xxxxxxxxxx> Add the bluetooth node for sc8280xp-crd and make it consume the outputs from the PMU as per the new DT bindings contract. Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@xxxxxxxxxx> --- arch/arm64/boot/dts/qcom/sc8280xp-crd.dts | 59 ++++++++++++++++++++++- 1 file changed, 58 insertions(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts b/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts index ec6bed8395b1..eac3a6ce0b65 100644 --- a/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts +++ b/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts @@ -20,6 +20,7 @@ aliases { i2c4 = &i2c4; i2c21 = &i2c21; serial0 = &uart17; + serial1 = &uart2; }; backlight: backlight { @@ -275,7 +276,7 @@ usb1_sbu_mux: endpoint { wcn6855-pmu { compatible = "qcom,wcn6855-pmu"; - pinctrl-0 = <&wlan_en>; + pinctrl-0 = <&bt_en>, <&wlan_en>; pinctrl-names = "default"; wlan-enable-gpios = <&tlmm 134 GPIO_ACTIVE_HIGH>; @@ -746,6 +747,27 @@ &sdc2 { status = "okay"; }; +&uart2 { + pinctrl-0 = <&uart2_default>; + pinctrl-names = "default"; + + status = "okay"; + + bluetooth { + compatible = "qcom,wcn6855-bt"; + + vddrfacmn-supply = <&vreg_pmu_rfa_cmn_0p8>; + vddaon-supply = <&vreg_pmu_aon_0p8>; + vddwlcx-supply = <&vreg_pmu_wlcx_0p8>; + vddwlmx-supply = <&vreg_pmu_wlmx_0p8>; + vddbtcmx-supply = <&vreg_pmu_btcmx_0p8>; + vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>; + vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>; + vddrfa1p8-supply = <&vreg_pmu_rfa_1p7>; + }; +}; + + &uart17 { compatible = "qcom,geni-debug-uart"; @@ -891,6 +913,13 @@ hastings_reg_en: hastings-reg-en-state { &tlmm { gpio-reserved-ranges = <74 6>, <83 4>, <125 2>, <128 2>, <154 7>; + bt_en: bt-en-state { + pins = "gpio133"; + function = "gpio"; + drive-strength = <16>; + bias-disable; + }; + edp_reg_en: edp-reg-en-state { pins = "gpio25"; function = "gpio"; @@ -1090,6 +1119,34 @@ reset-n-pins { }; }; + uart2_default: uart2-default-state { + cts-pins { + pins = "gpio121"; + function = "qup2"; + bias-bus-hold; + }; + + rts-pins { + pins = "gpio122"; + function = "qup2"; + drive-strength = <2>; + bias-disable; + }; + + rx-pins { + pins = "gpio124"; + function = "qup2"; + bias-pull-up; + }; + + tx-pins { + pins = "gpio123"; + function = "qup2"; + drive-strength = <2>; + bias-disable; + }; + }; + usb0_sbu_default: usb0-sbu-state { oe-n-pins { pins = "gpio101"; -- 2.43.0