CAN instances 0 and 1 in the mcu domain and 0 in the main domain are brought on the evm through headers J5, J8 and J10 respectively. Thus, add their respective transceiver's 0, 1 and 2 dt nodes as well as add the required pinmux to add support for these CAN instances. Signed-off-by: Bhavya Kapoor <b-kapoor@xxxxxx> Reviewed-by: Judith Mendez <jm@xxxxxx> --- Link to v1: https://lore.kernel.org/all/20240808082030.2812216-1-b-kapoor@xxxxxx/ changelog v1->v2: Modified code to maintain proper dts coding style arch/arm64/boot/dts/ti/k3-j722s-evm.dts | 74 +++++++++++++++++++++++++ 1 file changed, 74 insertions(+) diff --git a/arch/arm64/boot/dts/ti/k3-j722s-evm.dts b/arch/arm64/boot/dts/ti/k3-j722s-evm.dts index dd3b5f7039d7..8daa47a245aa 100644 --- a/arch/arm64/boot/dts/ti/k3-j722s-evm.dts +++ b/arch/arm64/boot/dts/ti/k3-j722s-evm.dts @@ -162,10 +162,39 @@ sound_master: simple-audio-card,codec { clocks = <&audio_refclk1>; }; }; + + transceiver0: can-phy0 { + compatible = "ti,tcan1042"; + #phy-cells = <0>; + max-bitrate = <5000000>; + pinctrl-names = "default"; + pinctrl-0 = <&mcu_mcan0_gpio_pins_default>; + standby-gpios = <&mcu_gpio0 12 GPIO_ACTIVE_HIGH>; + }; + + transceiver1: can-phy1 { + compatible = "ti,tcan1042"; + #phy-cells = <0>; + max-bitrate = <5000000>; + }; + + transceiver2: can-phy2 { + compatible = "ti,tcan1042"; + #phy-cells = <0>; + max-bitrate = <5000000>; + standby-gpios = <&exp1 17 GPIO_ACTIVE_HIGH>; + }; }; &main_pmx0 { + main_mcan0_pins_default: main-mcan0-default-pins { + pinctrl-single,pins = < + J722S_IOPAD(0x1dc, PIN_INPUT, 0) /* (C22) MCAN0_RX */ + J722S_IOPAD(0x1d8, PIN_OUTPUT, 0) /*(D22) MCAN0_TX */ + >; + }; + main_i2c0_pins_default: main-i2c0-default-pins { pinctrl-single,pins = < J722S_IOPAD(0x01e0, PIN_INPUT_PULLUP, 0) /* (D23) I2C0_SCL */ @@ -303,6 +332,26 @@ &main_uart0 { &mcu_pmx0 { + mcu_mcan0_pins_default: mcu-mcan0-default-pins { + pinctrl-single,pins = < + J722S_MCU_IOPAD(0x038, PIN_INPUT, 0) /* (D8) MCU_MCAN0_RX */ + J722S_MCU_IOPAD(0x034, PIN_OUTPUT, 0) /* (B2) MCU_MCAN0_TX */ + >; + }; + + mcu_mcan1_pins_default: mcu-mcan1-default-pins { + pinctrl-single,pins = < + J722S_MCU_IOPAD(0x040, PIN_INPUT, 0) /* (B1) MCU_MCAN1_RX */ + J722S_MCU_IOPAD(0x03C, PIN_OUTPUT, 0) /*(C1) MCU_MCAN1_TX */ + >; + }; + + mcu_mcan0_gpio_pins_default: mcu-mcan0-gpio-default-pins { + pinctrl-single,pins = < + J722S_MCU_IOPAD(0x0030, PIN_OUTPUT, 7) /* (C3) MCU_GPIO0_12 */ + >; + }; + wkup_uart0_pins_default: wkup-uart0-default-pins { pinctrl-single,pins = < J722S_MCU_IOPAD(0x02c, PIN_INPUT, 0) /* (C7) WKUP_UART0_CTSn */ @@ -566,3 +615,28 @@ &mcasp1 { 0 0 0 0 >; }; + +&mcu_mcan0 { + pinctrl-names = "default"; + pinctrl-0 = <&mcu_mcan0_pins_default>; + phys = <&transceiver0>; + status = "okay"; +}; + +&mcu_mcan1 { + pinctrl-names = "default"; + pinctrl-0 = <&mcu_mcan1_pins_default>; + phys = <&transceiver1>; + status = "okay"; +}; + +&main_mcan0 { + pinctrl-names = "default"; + pinctrl-0 = <&main_mcan0_pins_default>; + phys = <&transceiver2>; + status = "okay"; +}; + +&mcu_gpio0 { + status = "okay"; +}; -- 2.34.1
