On Sun, Aug 25, 2024 at 01:10:02PM GMT, Yixun Lan wrote:
> Add dt-binding for the pinctrl driver of SpacemiT's K1 SoC.
>
> Two vendor specific properties are introduced here, As the pinctrl
> has dedicated slew rate enable control - bit[7], so we have
> spacemit,slew-rate-{enable,disable} for this. For the same reason,
> creating spacemit,strong-pull-up for the strong pull up control.
>
> Signed-off-by: Yixun Lan <dlan@xxxxxxxxxx>
> ---
> .../bindings/pinctrl/spacemit,k1-pinctrl.yaml | 134 +++++++++++++++++
> include/dt-bindings/pinctrl/spacemit,k1-pinctrl.h | 161 +++++++++++++++++++++
> 2 files changed, 295 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/pinctrl/spacemit,k1-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/spacemit,k1-pinctrl.yaml
> new file mode 100644
> index 0000000000000..8adfc5ebbce37
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/spacemit,k1-pinctrl.yaml
> @@ -0,0 +1,134 @@
> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/pinctrl/spacemit,k1-pinctrl.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: SpacemiT K1 SoC Pin Controller
> +
> +maintainers:
> + - Yixun Lan <dlan@xxxxxxxxxx>
> +
> +properties:
> + compatible:
> + const: spacemit,k1-pinctrl
> +
> + reg:
> + items:
> + - description: pinctrl io memory base
> +
> +patternProperties:
> + '-cfg$':
> + type: object
> + description: |
> + A pinctrl node should contain at least one subnode representing the
> + pinctrl groups available on the machine.
> +
> + additionalProperties: false
> +
> + patternProperties:
> + '-pins$':
> + type: object
> + description: |
> + Each subnode will list the pins it needs, and how they should
> + be configured, with regard to muxer configuration, bias, input
> + enable/disable, input schmitt trigger, slew-rate enable/disable,
> + slew-rate, drive strength, power source.
> + $ref: /schemas/pinctrl/pincfg-node.yaml
> +
> + allOf:
> + - $ref: pincfg-node.yaml#
> + - $ref: pinmux-node.yaml#
> +
> + properties:
> + pinmux:
> + description: |
> + The list of GPIOs and their mux settings that properties in the
> + node apply to. This should be set using the K1_PADCONF macro to
> + construct the value.
> + $ref: /schemas/pinctrl/pinmux-node.yaml#/properties/pinmux
> +
> + bias-disable: true
> +
> + bias-pull-up: true
> +
> + bias-pull-down: true
> +
> + drive-strength-microamp:
> + description: |
> + typical current when output high level, but in mA.
> + 1.8V output: 11, 21, 32, 42 (mA)
> + 3.3V output: 7, 10, 13, 16, 19, 23, 26, 29 (mA)
> + $ref: /schemas/types.yaml#/definitions/uint32
> +
If there are no other runtime restrictions, you should add extra
check with the power-source, then you can always get vaild
settings.
Regards,
Inochi
> + input-schmitt:
> + description: |
> + typical threshold for schmitt trigger.
> + 0: buffer mode
> + 1: trigger mode
> + 2, 3: trigger mode
> + $ref: /schemas/types.yaml#/definitions/uint32
> + enum: [0, 1, 2, 3]
> +
> + power-source:
> + description: external power supplies at 1.8v or 3.3v.
> + enum: [ 1800, 3300 ]
> +
> + slew-rate:
> + description: |
> + slew rate for output buffer
> + 0, 1: Slow speed
> + 2: Medium speed
> + 3: Fast speed
> + $ref: /schemas/types.yaml#/definitions/uint32
> + enum: [0, 1, 2, 3]
> +
> + spacemit,slew-rate-enable:
> + description: enable slew rate.
> + type: boolean
> +
> + spacemit,slew-rate-disable:
> + description: disable slew rate.
> + type: boolean
> +
> + spacemit,strong-pull-up:
> + description: enable strong pull up.
> + type: boolean
> +
> + required:
> + - pinmux
> +
> + additionalProperties: false
> +
> +required:
> + - compatible
> + - reg
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/pinctrl/spacemit,k1-pinctrl.h>
> +
> + soc {
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + pinctrl@d401e000 {
> + compatible = "spacemit,k1-pinctrl";
> + reg = <0x0 0xd401e000 0x0 0x400>;
> + #pinctrl-cells = <2>;
> + #gpio-range-cells = <3>;
> +
> + uart0_2_cfg: uart0-2-cfg {
> + uart0-2-pins {
> + pinmux = <K1_PADCONF(GPIO_68, 2)>,
> + <K1_PADCONF(GPIO_69, 2)>;
> + bias-pull-up;
> + drive-strength-microamp = <32>;
> + };
> + };
> + };
> + };
> +
> +...
> diff --git a/include/dt-bindings/pinctrl/spacemit,k1-pinctrl.h b/include/dt-bindings/pinctrl/spacemit,k1-pinctrl.h
> new file mode 100644
> index 0000000000000..13ef4aa6c53a3
> --- /dev/null
> +++ b/include/dt-bindings/pinctrl/spacemit,k1-pinctrl.h
> @@ -0,0 +1,161 @@
> +/* SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause */
> +/*
> + * Copyright (c) 2022-2024 SpacemiT (Hangzhou) Technology Co. Ltd
> + * Copyright (c) 2024 Yixun Lan <dlan@xxxxxxxxxx>
> + *
> + */
> +
> +#ifndef _DT_BINDINGS_PINCTRL_K1_H
> +#define _DT_BINDINGS_PINCTRL_K1_H
> +
> +#define PINMUX(pin, mux) \
> + (((pin) & 0xffff) | (((mux) & 0xff) << 16))
> +
> +/* pin offset */
> +#define PINID(x) ((x) + 1)
> +
> +#define GPIO_INVAL 0
> +#define GPIO_00 PINID(0)
> +#define GPIO_01 PINID(1)
> +#define GPIO_02 PINID(2)
> +#define GPIO_03 PINID(3)
> +#define GPIO_04 PINID(4)
> +#define GPIO_05 PINID(5)
> +#define GPIO_06 PINID(6)
> +#define GPIO_07 PINID(7)
> +#define GPIO_08 PINID(8)
> +#define GPIO_09 PINID(9)
> +#define GPIO_10 PINID(10)
> +#define GPIO_11 PINID(11)
> +#define GPIO_12 PINID(12)
> +#define GPIO_13 PINID(13)
> +#define GPIO_14 PINID(14)
> +#define GPIO_15 PINID(15)
> +#define GPIO_16 PINID(16)
> +#define GPIO_17 PINID(17)
> +#define GPIO_18 PINID(18)
> +#define GPIO_19 PINID(19)
> +#define GPIO_20 PINID(20)
> +#define GPIO_21 PINID(21)
> +#define GPIO_22 PINID(22)
> +#define GPIO_23 PINID(23)
> +#define GPIO_24 PINID(24)
> +#define GPIO_25 PINID(25)
> +#define GPIO_26 PINID(26)
> +#define GPIO_27 PINID(27)
> +#define GPIO_28 PINID(28)
> +#define GPIO_29 PINID(29)
> +#define GPIO_30 PINID(30)
> +#define GPIO_31 PINID(31)
> +
> +#define GPIO_32 PINID(32)
> +#define GPIO_33 PINID(33)
> +#define GPIO_34 PINID(34)
> +#define GPIO_35 PINID(35)
> +#define GPIO_36 PINID(36)
> +#define GPIO_37 PINID(37)
> +#define GPIO_38 PINID(38)
> +#define GPIO_39 PINID(39)
> +#define GPIO_40 PINID(40)
> +#define GPIO_41 PINID(41)
> +#define GPIO_42 PINID(42)
> +#define GPIO_43 PINID(43)
> +#define GPIO_44 PINID(44)
> +#define GPIO_45 PINID(45)
> +#define GPIO_46 PINID(46)
> +#define GPIO_47 PINID(47)
> +#define GPIO_48 PINID(48)
> +#define GPIO_49 PINID(49)
> +#define GPIO_50 PINID(50)
> +#define GPIO_51 PINID(51)
> +#define GPIO_52 PINID(52)
> +#define GPIO_53 PINID(53)
> +#define GPIO_54 PINID(54)
> +#define GPIO_55 PINID(55)
> +#define GPIO_56 PINID(56)
> +#define GPIO_57 PINID(57)
> +#define GPIO_58 PINID(58)
> +#define GPIO_59 PINID(59)
> +#define GPIO_60 PINID(60)
> +#define GPIO_61 PINID(61)
> +#define GPIO_62 PINID(62)
> +#define GPIO_63 PINID(63)
> +
> +#define GPIO_64 PINID(64)
> +#define GPIO_65 PINID(65)
> +#define GPIO_66 PINID(66)
> +#define GPIO_67 PINID(67)
> +#define GPIO_68 PINID(68)
> +#define GPIO_69 PINID(69)
> +#define GPIO_70 PINID(70)
> +#define GPIO_71 PINID(71)
> +#define GPIO_72 PINID(72)
> +#define GPIO_73 PINID(73)
> +#define GPIO_74 PINID(74)
> +#define GPIO_75 PINID(75)
> +#define GPIO_76 PINID(76)
> +#define GPIO_77 PINID(77)
> +#define GPIO_78 PINID(78)
> +#define GPIO_79 PINID(79)
> +#define GPIO_80 PINID(80)
> +#define GPIO_81 PINID(81)
> +#define GPIO_82 PINID(82)
> +#define GPIO_83 PINID(83)
> +#define GPIO_84 PINID(84)
> +#define GPIO_85 PINID(85)
> +
> +#define GPIO_101 PINID(89)
> +#define GPIO_100 PINID(90)
> +#define GPIO_99 PINID(91)
> +#define GPIO_98 PINID(92)
> +#define GPIO_103 PINID(93)
> +#define GPIO_102 PINID(94)
> +
> +#define GPIO_104 PINID(109)
> +#define GPIO_105 PINID(110)
> +#define GPIO_106 PINID(111)
> +#define GPIO_107 PINID(112)
> +#define GPIO_108 PINID(113)
> +#define GPIO_109 PINID(114)
> +#define GPIO_110 PINID(115)
> +
> +#define GPIO_93 PINID(116)
> +#define GPIO_94 PINID(117)
> +#define GPIO_95 PINID(118)
> +#define GPIO_96 PINID(119)
> +#define GPIO_97 PINID(120)
> +
> +#define GPIO_86 PINID(122)
> +#define GPIO_87 PINID(123)
> +#define GPIO_88 PINID(124)
> +#define GPIO_89 PINID(125)
> +#define GPIO_90 PINID(126)
> +#define GPIO_91 PINID(127)
> +#define GPIO_92 PINID(128)
> +
> +#define GPIO_111 PINID(130)
> +#define GPIO_112 PINID(131)
> +#define GPIO_113 PINID(132)
> +#define GPIO_114 PINID(133)
> +#define GPIO_115 PINID(134)
> +#define GPIO_116 PINID(135)
> +#define GPIO_117 PINID(136)
> +#define GPIO_118 PINID(137)
> +#define GPIO_119 PINID(138)
> +#define GPIO_120 PINID(139)
> +#define GPIO_121 PINID(140)
> +#define GPIO_122 PINID(141)
> +#define GPIO_123 PINID(142)
> +#define GPIO_124 PINID(143)
> +#define GPIO_125 PINID(144)
> +#define GPIO_126 PINID(145)
> +#define GPIO_127 PINID(146)
> +
> +#define SLEW_RATE_SLOW0 0
> +#define SLEW_RATE_SLOW1 1
> +#define SLEW_RATE_MEDIUM 2
> +#define SLEW_RATE_FAST 3
> +
> +#define K1_PADCONF(pin, func) (((pin) << 16) | (func))
> +
> +#endif /* _DT_BINDINGS_PINCTRL_K1_H */
>
> --
> 2.45.2
>
