On Fri, Aug 23, 2024 at 08:17:11PM +0200, Vasileios Amoiridis wrote:
> This commit adds forced mode support in sensors BMP28x, BME28x, BMP3xx
> and BMP58x. Sensors BMP18x and BMP085 are old and do not support this
> feature so their operation is not affected at all.
>
> Essentially, up to now, the rest of the sensors were used in normal mode
> all the time. This means that they are continuously doing measurements
> even though these measurements are not used. Even though the sensor does
> provide PM support, to cover all the possible use cases, the sensor needs
> to go into sleep mode and wake up whenever necessary.
>
> This commit, adds sleep and forced mode support. Essentially, the sensor
> sleeps all the time except for when a measurement is requested. When there
> is a request for a measurement, the sensor is put into forced mode, starts
> the measurement and after it is done we read the output and we put it again
> in sleep mode.
>
> For really fast and more deterministic measurements, the triggered buffer
> interface can be used, since the sensor is still used in normal mode for
> that use case.
>
> This commit does not add though support for DEEP STANDBY, Low Power NORMAL
> and CONTINUOUS modes, supported only by the BMP58x version.
...
> +static const u8 bmp280_operation_mode[] = { BMP280_MODE_SLEEP,
> + BMP280_MODE_FORCED,
> + BMP280_MODE_NORMAL };
Better style is
static const u8 bmp280_operation_mode[] = {
BMP280_MODE_SLEEP, BMP280_MODE_FORCED, BMP280_MODE_NORMAL,
};
Also note comma at the end.
...
> +static int bmp280_wait_conv(struct bmp280_data *data)
> +{
> + unsigned int reg;
> + int ret, meas_time;
> +
> + meas_time = BMP280_MEAS_OFFSET;
> +
> + /* Check if we are using a BME280 device */
> + if (data->oversampling_humid)
> + meas_time += (1 << data->oversampling_humid) * BMP280_MEAS_DUR +
BIT(data->oversampling_humid)
> + BMP280_PRESS_HUMID_MEAS_OFFSET;
> + /* Pressure measurement time */
> + meas_time += (1 << data->oversampling_press) * BMP280_MEAS_DUR +
Ditto.
> + BMP280_PRESS_HUMID_MEAS_OFFSET;
> + /* Temperature measurement time */
> + meas_time += (1 << data->oversampling_temp) * BMP280_MEAS_DUR;
Ditto.
> + usleep_range(meas_time, meas_time * 12 / 10);
fsleep() ?
> + ret = regmap_read(data->regmap, BMP280_REG_STATUS, ®);
> + if (ret) {
> + dev_err(data->dev, "failed to read status register\n");
> + return ret;
> + }
> + if (reg & BMP280_REG_STATUS_MEAS_BIT) {
> + dev_err(data->dev, "Measurement cycle didn't complete\n");
> + return -EBUSY;
> + }
> +
> + return 0;
> +}
...
> +static const u8 bmp380_operation_mode[] = { BMP380_MODE_SLEEP,
> + BMP380_MODE_FORCED,
> + BMP380_MODE_NORMAL };
As per above.
...
> +static int bmp380_wait_conv(struct bmp280_data *data)
> +{
As per above comments against bmp280_wait_conv().
> + ret = regmap_read(data->regmap, BMP380_REG_STATUS, ®);
> + if (ret) {
> + dev_err(data->dev, "failed to read status register\n");
> + return ret;
> + }
> +
Choose one style (with or without blank line), as in the above you have no
blank line in the similar situation.
> + if (!(reg & BMP380_STATUS_DRDY_PRESS_MASK) ||
> + !(reg & BMP380_STATUS_DRDY_TEMP_MASK)) {
> + dev_err(data->dev, "Measurement cycle didn't complete.\n");
> + return -EBUSY;
> + }
> +
> + return 0;
> +}
...
> + usleep_range(data->start_up_time, data->start_up_time + 500);
fsleep() ? Comment?
...
> +static const u8 bmp580_operation_mode[] = { BMP580_MODE_SLEEP,
> + BMP580_MODE_FORCED,
> + BMP580_MODE_NORMAL };
As per above.
...
> + switch (mode) {
> + case BMP280_SLEEP:
> + break;
> + case BMP280_FORCED:
> + ret = regmap_set_bits(data->regmap, BMP580_REG_DSP_CONFIG,
> + BMP580_DSP_IIR_FORCED_FLUSH);
> + if (ret) {
> + dev_err(data->dev,
> + "Could not flush IIR filter constants.\n");
> + return ret;
> + }
> + break;
> + case BMP280_NORMAL:
> + break;
Can be unified with _SLEEP case.
> + default:
> + return -EINVAL;
> + }
...
> +static int bmp580_wait_conv(struct bmp280_data *data)
> +{
> + /*
> + * Taken from datasheet, Section 2 "Specification, Table 3 "Electrical
> + * characteristics
Missing period.
> + */
> + static const int time_conv_press[] = { 0, 1050, 1785, 3045, 5670, 10920, 21420,
> + 42420, 84420};
> + static const int time_conv_temp[] = { 0, 1050, 1105, 1575, 2205, 3465, 6090,
> + 11340, 21840};
Please, start values on the next line after {. Also make }; to be on a separate line.
> + int meas_time;
> +
> + meas_time = 4000 + time_conv_temp[data->oversampling_temp] +
> + time_conv_press[data->oversampling_press];
4 * USEC_PER_MSEC ?
> + usleep_range(meas_time, meas_time * 12 / 10);
Comment? fsleep() ?
> + return 0;
> +}
...
> + usleep_range(2500, 3000);
fsleep() ?
--
With Best Regards,
Andy Shevchenko
