> -----Original Message-----
> From: Biju Das <biju.das.jz@xxxxxxxxxxxxxx>
> Sent: Friday, August 23, 2024 11:51 AM
> To: Geert Uytterhoeven <geert@xxxxxxxxxxxxxx>; Rob Herring <robh@xxxxxxxxxx>; Krzysztof Kozlowski
> <krzk+dt@xxxxxxxxxx>; Conor Dooley <conor+dt@xxxxxxxxxx>
> Cc: Liam Girdwood <lgirdwood@xxxxxxxxx>; Mark Brown <broonie@xxxxxxxxxx>; Magnus Damm
> <magnus.damm@xxxxxxxxx>; linux-sound@xxxxxxxxxxxxxxx; devicetree@xxxxxxxxxxxxxxx; linux-renesas-
> soc@xxxxxxxxxxxxxxx; Prabhakar Mahadev Lad <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx>; biju.das.au
> <biju.das.au@xxxxxxxxx>
> Subject: RE: [PATCH 2/3] arm64: dts: renesas: rzg2l-smarc: Enable HDMI audio
>
> Hi All,
>
> > -----Original Message-----
> > From: Geert Uytterhoeven <geert@xxxxxxxxxxxxxx>
> > Sent: Friday, August 23, 2024 10:59 AM
> > Subject: Re: [PATCH 2/3] arm64: dts: renesas: rzg2l-smarc: Enable HDMI
> > audio
> >
> > Hi Biju,
> >
> > On Thu, Jul 25, 2024 at 10:46 AM Biju Das <biju.das.jz@xxxxxxxxxxxxxx> wrote:
> > > Enable HDMI audio on RZ/{G2L,V2L} SMARC EVK.
> > >
> > > Signed-off-by: Biju Das <biju.das.jz@xxxxxxxxxxxxxx>
> >
> > Thanks for your patch!
> >
> > > --- a/arch/arm64/boot/dts/renesas/rzg2l-smarc-pinfunction.dtsi
> > > +++ b/arch/arm64/boot/dts/renesas/rzg2l-smarc-pinfunction.dtsi
> > > @@ -143,6 +143,13 @@ ssi0_pins: ssi0 {
> > > <RZG2L_PORT_PINMUX(45, 3, 1)>; /* RXD */
> > > };
> > >
> > > + ssi1_pins: ssi1 {
> > > + pinmux = <RZG2L_PORT_PINMUX(46, 0, 1)>, /* BCK */
> > > + <RZG2L_PORT_PINMUX(46, 1, 1)>, /* RCK */
> > > + <RZG2L_PORT_PINMUX(46, 2, 1)>, /* TXD */
> > > + <RZG2L_PORT_PINMUX(46, 3, 1)>; /* RXD */
> >
> > RXD/I2S2_SDIN is not wired on the carrier board.
> > OK to drop it?
> >
> > The rest LGTM (but I'm no audio bindings expert).
>
The below comment is for RZ/G2LC SoC, where switch postion determines whether ssi0 signal is connected to
Audio codec or to the HDMI audio.
> Is dt binding check allows conditional macros?
>
> Based on switch position audio signal ssi0 is routed to Audio codec Or routed to HDMI audio
> port
>
> The former one does not use graph where as latter one uses audio graph How do I describe this in
> bindings?
>
> like dts, something like below supported in dt bindings??
>
> #if X
> Audio codec
> #else
> HDMI Audio
> #endif
>
> Cheers,
> Biju
