On Fri, 09 Aug 2024 11:48:13 -0700, Oreoluwa Babatunde wrote: > Reserved memory regions defined in the devicetree can be broken up into > two groups: > i) Statically-placed reserved memory regions > i.e. regions defined with a static start address and size using the > "reg" property. > ii) Dynamically-placed reserved memory regions. > i.e. regions defined by specifying an address range where they can be > placed in memory using the "alloc_ranges" and "size" properties. > > These regions are processed and set aside at boot time. > This is done in two stages as seen below: > > Stage 1: > At this stage, fdt_scan_reserved_mem() scans through the child nodes of > the reserved_memory node using the flattened devicetree and does the > following: > > 1) If the node represents a statically-placed reserved memory region, > i.e. if it is defined using the "reg" property: > - Call memblock_reserve() or memblock_mark_nomap() as needed. > - Add the information for that region into the reserved_mem array > using fdt_reserved_mem_save_node(). > i.e. fdt_reserved_mem_save_node(node, name, base, size). > > 2) If the node represents a dynamically-placed reserved memory region, > i.e. if it is defined using "alloc-ranges" and "size" properties: > - Add the information for that region to the reserved_mem array with > the starting address and size set to 0. > i.e. fdt_reserved_mem_save_node(node, name, 0, 0). > Note: This region is saved to the array with a starting address of 0 > because a starting address is not yet allocated for it. > > Stage 2: > After iterating through all the reserved memory nodes and storing their > relevant information in the reserved_mem array,fdt_init_reserved_mem() is > called and does the following: > > 1) For statically-placed reserved memory regions: > - Call the region specific init function using > __reserved_mem_init_node(). > 2) For dynamically-placed reserved memory regions: > - Call __reserved_mem_alloc_size() which is used to allocate memory > for each of these regions, and mark them as nomap if they have the > nomap property specified in the DT. > - Call the region specific init function. > > The current size of the resvered_mem array is 64 as is defined by > MAX_RESERVED_REGIONS. This means that there is a limitation of 64 for > how many reserved memory regions can be specified on a system. > As systems continue to grow more and more complex, the number of > reserved memory regions needed are also growing and are starting to hit > this 64 count limit, hence the need to make the reserved_mem array > dynamically sized (i.e. dynamically allocating memory for the > reserved_mem array using membock_alloc_*). > > On architectures such as arm64, memory allocated using memblock is > writable only after the page tables have been setup. This means that if > the reserved_mem array is going to be dynamically allocated, it needs to > happen after the page tables have been setup, not before. > > Since the reserved memory regions are currently being processed and > added to the array before the page tables are setup, there is a need to > change the order in which some of the processing is done to allow for > the reserved_mem array to be dynamically sized. > > It is possible to process the statically-placed reserved memory regions > without needing to store them in the reserved_mem array until after the > page tables have been setup because all the information stored in the > array is readily available in the devicetree and can be referenced at > any time. > Dynamically-placed reserved memory regions on the other hand get > assigned a start address only at runtime, and hence need a place to be > stored once they are allocated since there is no other referrence to the > start address for these regions. > > Hence this patch changes the processing order of the reserved memory > regions in the following ways: > > Step 1: > fdt_scan_reserved_mem() scans through the child nodes of > the reserved_memory node using the flattened devicetree and does the > following: > > 1) If the node represents a statically-placed reserved memory region, > i.e. if it is defined using the "reg" property: > - Call memblock_reserve() or memblock_mark_nomap() as needed. > - Call the region specific initialization function for the region > using fdt_init_reserved_mem_node(). > > 2) If the node represents a dynamically-placed reserved memory region, > i.e. if it is defined using "alloc-ranges" and "size" properties: > - Call __reserved_mem_alloc_size() which will: > i) Allocate memory for the reserved region and call > memblock_mark_nomap() as needed. > ii) Call the region specific initialization function using > fdt_init_reserved_mem_node(). > iii) Save the region information in the reserved_mem array using > fdt_reserved_mem_save_node(). > > Step 2: > 1) This stage of the reserved memory processing is now only used to add > the statically-placed reserved memory regions into the reserved_mem > array using fdt_scan_reserved_mem_reg_nodes(). > > 2) This step is also moved to be after the page tables have been > setup. Moving this will allow us to replace the reserved_mem > array with a dynamically sized array before storing the rest of > these regions. > > Signed-off-by: Oreoluwa Babatunde <quic_obabatun@xxxxxxxxxxx> > --- > drivers/of/fdt.c | 5 +- > drivers/of/of_private.h | 3 +- > drivers/of/of_reserved_mem.c | 172 +++++++++++++++++++++++++---------- > 3 files changed, 131 insertions(+), 49 deletions(-) > Applied, thanks!
