From: Bartosz Golaszewski <bartosz.golaszewski@xxxxxxxxxx>
Add the bluetooth node for sc8280xp-crd and make it consume the outputs
from the PMU as per the new DT bindings contract.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@xxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/sc8280xp-crd.dts | 59 ++++++++++++++++++++++-
1 file changed, 58 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts b/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts
index 57efeefbc89e..7bd7cd310bf0 100644
--- a/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts
+++ b/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts
@@ -20,6 +20,7 @@ aliases {
i2c4 = &i2c4;
i2c21 = &i2c21;
serial0 = &uart17;
+ serial1 = &uart2;
};
backlight: backlight {
@@ -275,7 +276,7 @@ usb1_sbu_mux: endpoint {
wcn6855-pmu {
compatible = "qcom,wcn6855-pmu";
- pinctrl-0 = <&wlan_en>;
+ pinctrl-0 = <&bt_en>, <&wlan_en>;
pinctrl-names = "default";
wlan-enable-gpios = <&tlmm 134 GPIO_ACTIVE_HIGH>;
@@ -748,6 +749,27 @@ &sdc2 {
status = "okay";
};
+&uart2 {
+ pinctrl-0 = <&uart2_default>;
+ pinctrl-names = "default";
+
+ status = "okay";
+
+ bluetooth {
+ compatible = "qcom,wcn6855-bt";
+
+ vddrfacmn-supply = <&vreg_pmu_rfa_cmn_0p8>;
+ vddaon-supply = <&vreg_pmu_aon_0p8>;
+ vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+ vddwlmx-supply = <&vreg_pmu_wlmx_0p8>;
+ vddbtcmx-supply = <&vreg_pmu_btcmx_0p8>;
+ vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+ vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+ vddrfa1p8-supply = <&vreg_pmu_rfa_1p7>;
+ };
+};
+
+
&uart17 {
compatible = "qcom,geni-debug-uart";
@@ -893,6 +915,13 @@ hastings_reg_en: hastings-reg-en-state {
&tlmm {
gpio-reserved-ranges = <74 6>, <83 4>, <125 2>, <128 2>, <154 7>;
+ bt_en: bt-en-state {
+ pins = "gpio133";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
edp_reg_en: edp-reg-en-state {
pins = "gpio25";
function = "gpio";
@@ -1093,6 +1122,34 @@ reset-n-pins {
};
};
+ uart2_default: uart2-default-state {
+ cts-pins {
+ pins = "gpio121";
+ function = "qup2";
+ bias-bus-hold;
+ };
+
+ rts-pins {
+ pins = "gpio122";
+ function = "qup2";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ rx-pins {
+ pins = "gpio124";
+ function = "qup2";
+ bias-pull-up;
+ };
+
+ tx-pins {
+ pins = "gpio123";
+ function = "qup2";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+
usb0_sbu_default: usb0-sbu-state {
oe-n-pins {
pins = "gpio101";
--
2.43.0
