Introduce device-tree binding documentation for Airoha EN7581 pinctrl controller. Signed-off-by: Lorenzo Bianconi <lorenzo@xxxxxxxxxx> --- .../pinctrl/airoha,en7581-pinctrl.yaml | 467 ++++++++++++++++++ 1 file changed, 467 insertions(+) create mode 100644 Documentation/devicetree/bindings/pinctrl/airoha,en7581-pinctrl.yaml diff --git a/Documentation/devicetree/bindings/pinctrl/airoha,en7581-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/airoha,en7581-pinctrl.yaml new file mode 100644 index 000000000000..b1f980613864 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/airoha,en7581-pinctrl.yaml @@ -0,0 +1,467 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/airoha,en7581-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Airoha EN7581 Pin Controller + +maintainers: + - Lorenzo Bianconi <lorenzo@xxxxxxxxxx> + +description: + The Airoha's EN7581 Pin controller is used to control SoC pins. + +properties: + compatible: + enum: + - airoha,en7581-pinctrl + + reg: + items: + - description: IOMUX base address + - description: LED IOMUX base address + - description: GPIO flash mode base address + - description: GPIO flash mode extended base address + - description: IO pin configuration base address + - description: PCIE reset open-drain base address + - description: GPIO bank0 data register base address + - description: GPIO bank1 data register base address + - description: GPIO bank0 first control register base address + - description: GPIO bank0 second control register base address + - description: GPIO bank1 first control register base address + - description: GPIO bank1 second control register base address + - description: GPIO bank0 output enable register base address + - description: GPIO bank1 output enable register base address + - description: GPIO bank0 irq status register base address + - description: GPIO bank1 irq status register base address + - description: GPIO bank0 irq level first control register base address + - description: GPIO bank0 irq level second control register base address + - description: GPIO bank1 irq level first control register base address + - description: GPIO bank1 irq level second control register base address + - description: GPIO bank0 irq edge first control register base address + - description: GPIO bank0 irq edge second control register base address + - description: GPIO bank1 irq edge first control register base address + - description: GPIO bank1 irq edge second control register base address + + gpio-controller: true + + "#gpio-cells": + const: 2 + description: + Number of cells in GPIO specifier. Since the generic GPIO binding is + used, the amount of cells must be specified as 2. See the below mentioned + gpio binding representation for description of particular cells. + + gpio-ranges: + maxItems: 1 + description: + GPIO valid number range. + + interrupt-controller: true + + interrupts: + maxItems: 1 + + "#interrupt-cells": + const: 2 + +allOf: + - $ref: pinctrl.yaml# + +required: + - compatible + - reg + - gpio-controller + - "#gpio-cells" + +patternProperties: + '-pins$': + type: object + additionalProperties: false + + patternProperties: + '^.*mux.*$': + type: object + additionalProperties: false + description: | + pinmux configuration nodes. + + $ref: /schemas/pinctrl/pinmux-node.yaml + properties: + function: + description: + A string containing the name of the function to mux to the group. + enum: [pon, tod_1pps, sipo, mdio, uart, i2c, jtag, pcm, spi, + pcm_spi, i2s, emmc, pnand, pcie_reset, pwm, phy1_led0, + phy2_led0, phy3_led0, phy4_led0, phy1_led1, phy2_led1, + phy3_led1, phy4_led1] + groups: + description: + An array of strings. Each string contains the name of a group. + required: + - function + - groups + + allOf: + - if: + properties: + function: + const: pon + then: + properties: + groups: + enum: [pon] + - if: + properties: + function: + const: tod_1pps + then: + properties: + groups: + enum: [pon_tod_1pps, gsw_tod_1pps] + - if: + properties: + function: + const: sipo + then: + properties: + groups: + enum: [sipo, sipo_rclk] + - if: + properties: + function: + const: mdio + then: + properties: + groups: + enum: [mdio] + - if: + properties: + function: + const: uart + then: + properties: + groups: + items: + enum: [uart2, uart2_cts_rts, hsuart, hsuart_cts_rts, uart4, + uart5] + maxItems: 2 + - if: + properties: + function: + const: i2c + then: + properties: + groups: + enum: [i2c1] + - if: + properties: + function: + const: jtag + then: + properties: + groups: + enum: [jtag_udi, jtag_dfd] + - if: + properties: + function: + const: pcm + then: + properties: + groups: + enum: [pcm1, pcm2] + - if: + properties: + function: + const: spi + then: + properties: + groups: + items: + enum: [spi_quad, spi_cs1] + maxItems: 2 + - if: + properties: + function: + const: pcm_spi + then: + properties: + groups: + items: + enum: [pcm_spi, pcm_spi_int, pcm_spi_rst, pcm_spi_cs1, + pcm_spi_cs2_p156, pcm_spi_cs2_p128, pcm_spi_cs3, + pcm_spi_cs4] + maxItems: 7 + - if: + properties: + function: + const: i2c + then: + properties: + groups: + enum: [i2s] + - if: + properties: + function: + const: emmc + then: + properties: + groups: + enum: [emmc] + - if: + properties: + function: + const: pnand + then: + properties: + groups: + enum: [pnand] + - if: + properties: + function: + const: pcie_reset + then: + properties: + groups: + enum: [pcie_reset0, pcie_reset1, pcie_reset2] + - if: + properties: + function: + const: pwm + then: + properties: + groups: + enum: [gpio0, gpio1, gpio2, gpio3, gpio4, gpio5, gpio6, + gpio7, gpio8, gpio9, gpio10, gpio11, gpio12, gpio13, + gpio14, gpio15, gpio16, gpio17, gpio18, gpio19, + gpio20, gpio21, gpio22, gpio23, gpio24, gpio25, + gpio26, gpio27, gpio28, gpio29, gpio30, gpio31, + gpio36, gpio37, gpio38, gpio39, gpio40, gpio41, + gpio42, gpio43, gpio44, gpio45, gpio46, gpio47] + - if: + properties: + function: + const: phy1_led0 + then: + properties: + groups: + enum: [gpio33, gpio34, gpio35, gpio42] + - if: + properties: + function: + const: phy2_led0 + then: + properties: + groups: + enum: [gpio33, gpio34, gpio35, gpio42] + - if: + properties: + function: + const: phy3_led0 + then: + properties: + groups: + enum: [gpio33, gpio34, gpio35, gpio42] + - if: + properties: + function: + const: phy4_led0 + then: + properties: + groups: + enum: [gpio33, gpio34, gpio35, gpio42] + - if: + properties: + function: + const: phy1_led1 + then: + properties: + groups: + enum: [gpio43, gpio44, gpio45, gpio46] + - if: + properties: + function: + const: phy2_led1 + then: + properties: + groups: + enum: [gpio43, gpio44, gpio45, gpio46] + - if: + properties: + function: + const: phy3_led1 + then: + properties: + groups: + enum: [gpio43, gpio44, gpio45, gpio46] + - if: + properties: + function: + const: phy4_led1 + then: + properties: + groups: + enum: [gpio43, gpio44, gpio45, gpio46] + + '^.*conf.*$': + type: object + additionalProperties: false + description: + pinconf configuration nodes. + $ref: /schemas/pinctrl/pincfg-node.yaml + + properties: + pins: + description: + An array of strings. Each string contains the name of a pin. + items: + enum: [uart1_txd, uart1_rxd, i2c_scl, i2c_sda, spi_cs0, spi_clk, + spi_mosi, spi_miso, gpio0, gpio1, gpio2, gpio3, gpio4, + gpio5, gpio6, gpio7, gpio8, gpio9, gpio10, gpio11, gpio12, + gpio13, gpio14, gpio15, gpio16, gpio17, gpio18, gpio19, + gpio20, gpio21, gpio22, gpio23, gpio24, gpio25, gpio26, + gpio27, gpio28, gpio29, gpio30, gpio31, gpio32, gpio33, + gpio34, gpio35, gpio36, gpio37, gpio38, gpio39, gpio40, + gpio41, gpio42, gpio43, gpio44, gpio45, gpio46, + pcie_reset0, pcie_reset1, pcie_reset2] + maxItems: 58 + + bias-disable: true + + bias-pull-up: true + + bias-pull-down: true + + input-enable: true + + output-enable: true + + output-low: true + + output-high: true + + drive-open-drain: true + + drive-strength: + enum: [2, 4, 6, 8] + + required: + - pins + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + + pio: pinctrl@1fa20214 { + compatible = "airoha,en7581-pinctrl"; + reg = <0x0 0x1fa20214 0x0 0x30>, + <0x0 0x1fa2027c 0x0 0x8>, + <0x0 0x1fbf0234 0x0 0x4>, + <0x0 0x1fbf0268 0x0 0x4>, + <0x0 0x1fa2001c 0x0 0x50>, + <0x0 0x1fa2018c 0x0 0x4>, + <0x0 0x1fbf0204 0x0 0x4>, + <0x0 0x1fbf0270 0x0 0x4>, + <0x0 0x1fbf0200 0x0 0x4>, + <0x0 0x1fbf0220 0x0 0x4>, + <0x0 0x1fbf0260 0x0 0x4>, + <0x0 0x1fbf0264 0x0 0x4>, + <0x0 0x1fbf0214 0x0 0x4>, + <0x0 0x1fbf0278 0x0 0x4>, + <0x0 0x1fbf0208 0x0 0x4>, + <0x0 0x1fbf027c 0x0 0x4>, + <0x0 0x1fbf0210 0x0 0x4>, + <0x0 0x1fbf028c 0x0 0x4>, + <0x0 0x1fbf0290 0x0 0x4>, + <0x0 0x1fbf0294 0x0 0x4>, + <0x0 0x1fbf020c 0x0 0x4>, + <0x0 0x1fbf0280 0x0 0x4>, + <0x0 0x1fbf0284 0x0 0x4>, + <0x0 0x1fbf0288 0x0 0x4>; + + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pio 0 13 47>; + + interrupt-controller; + #interrupt-cells = <2>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; + + pcie1-rst-pins { + conf { + pins = "pcie_reset1"; + drive-open-drain = <1>; + }; + }; + + pwm-pins { + mux { + function = "pwm"; + groups = "gpio18"; + }; + }; + + spi-pins { + mux { + function = "spi"; + groups = "spi_quad", "spi_cs1"; + }; + }; + + uuart2-pins { + mux { + function = "uart"; + groups = "uart2", "uart2_cts_rts"; + }; + }; + + uar5-pins { + mux { + function = "uart"; + groups = "uart5"; + }; + }; + + mmc-pins { + mux { + function = "emmc"; + groups = "emmc"; + }; + }; + + mdio-pins { + mux { + function = "mdio"; + groups = "mdio"; + }; + + conf { + pins = "gpio2"; + output-enable; + }; + }; + + gswp1-led0-pins { + mux { + function = "phy1_led0"; + groups = "gpio33"; + }; + }; + + gswp2-led1-pins { + mux { + function = "phy2_led1"; + groups = "gpio44"; + }; + }; + }; + }; -- 2.46.0
