On 30/07/2024 10:46, Lorenzo Bianconi wrote:
Introduce support for the DSA built-in switch available on the EN7581
development board. EN7581 support is similar to MT7988 one except
it requires to set MT7530_FORCE_MODE bit in MT753X_PMCR_P register
for on cpu port.
Tested-by: Benjamin Larsson <benjamin.larsson@xxxxxxxxxx>
Signed-off-by: Lorenzo Bianconi <lorenzo@xxxxxxxxxx>
---
drivers/net/dsa/mt7530-mmio.c | 1 +
drivers/net/dsa/mt7530.c | 38 +++++++++++++++++++++++++++++++----
drivers/net/dsa/mt7530.h | 16 ++++++++++-----
3 files changed, 46 insertions(+), 9 deletions(-)
diff --git a/drivers/net/dsa/mt7530-mmio.c b/drivers/net/dsa/mt7530-mmio.c
index b74a230a3f13..10dc49961f15 100644
--- a/drivers/net/dsa/mt7530-mmio.c
+++ b/drivers/net/dsa/mt7530-mmio.c
@@ -11,6 +11,7 @@
#include "mt7530.h"
static const struct of_device_id mt7988_of_match[] = {
+ { .compatible = "airoha,en7581-switch", .data = &mt753x_table[ID_EN7581], },
{ .compatible = "mediatek,mt7988-switch", .data = &mt753x_table[ID_MT7988], },
{ /* sentinel */ },
};
diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
index ec18e68bf3a8..8adc4561c5b2 100644
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -1152,7 +1152,8 @@ mt753x_cpu_port_enable(struct dsa_switch *ds, int port)
* the MT7988 SoC. Trapped frames will be forwarded to the CPU port that
* is affine to the inbound user port.
*/
- if (priv->id == ID_MT7531 || priv->id == ID_MT7988)
+ if (priv->id == ID_MT7531 || priv->id == ID_MT7988 ||
+ priv->id == ID_EN7581)
mt7530_set(priv, MT7531_CFC, MT7531_CPU_PMAP(BIT(port)));
/* CPU port gets connected to all user ports of
@@ -2207,7 +2208,7 @@ mt7530_setup_irq(struct mt7530_priv *priv)
return priv->irq ? : -EINVAL;
}
- if (priv->id == ID_MT7988)
+ if (priv->id == ID_MT7988 || priv->id == ID_EN7581)
priv->irq_domain = irq_domain_add_linear(np, MT7530_NUM_PHYS,
&mt7988_irq_domain_ops,
priv);
@@ -2766,7 +2767,7 @@ static void mt7988_mac_port_get_caps(struct dsa_switch *ds, int port,
{
switch (port) {
/* Ports which are connected to switch PHYs. There is no MII pinout. */
- case 0 ... 3:
+ case 0 ... 4:
Please create a new function, such as en7581_mac_port_get_caps().
__set_bit(PHY_INTERFACE_MODE_INTERNAL,
config->supported_interfaces);
@@ -2850,6 +2851,23 @@ mt7531_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
}
}
+static void
+en7581_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
+ phy_interface_t interface)
+{
+ /* BIT(31-27): reserved
+ * BIT(26): TX_CRC_EN: enable(0)/disable(1) CRC insertion
+ * BIT(25): RX_CRC_EN: enable(0)/disable(1) CRC insertion
+ * Since the bits above have a different meaning with respect to the
+ * one described in mt7530.h, set default values.
+ */
+ mt7530_clear(ds->priv, MT753X_PMCR_P(port), MT7531_FORCE_MODE_MASK);
+ if (dsa_is_cpu_port(ds, port)) {
+ /* enable MT7530_FORCE_MODE on cpu port */
+ mt7530_set(ds->priv, MT753X_PMCR_P(port), MT7530_FORCE_MODE);
+ }
+}
This seems to undo "Clear link settings and enable force mode to force link
down on all ports until they're enabled later." on mt7531_setup_common()
and redo it only for the CPU port. It should be so that force mode is
enabled on all ports. You could position the diff below as a patch before
this patch. It introduces the MT753X_FORCE_MODE() macro to choose the
correct constant for the switch model.
diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
index ec18e68bf3a8..4915264c460f 100644
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -2438,8 +2438,10 @@ mt7530_setup(struct dsa_switch *ds)
/* Clear link settings and enable force mode to force link down
* on all ports until they're enabled later.
*/
- mt7530_rmw(priv, MT753X_PMCR_P(i), PMCR_LINK_SETTINGS_MASK |
- MT7530_FORCE_MODE, MT7530_FORCE_MODE);
+ mt7530_rmw(priv, MT753X_PMCR_P(i),
+ PMCR_LINK_SETTINGS_MASK |
+ MT753X_FORCE_MODE(priv->id),
+ MT753X_FORCE_MODE(priv->id));
/* Disable forwarding by default on all ports */
mt7530_rmw(priv, MT7530_PCR_P(i), PCR_MATRIX_MASK,
@@ -2550,8 +2552,10 @@ mt7531_setup_common(struct dsa_switch *ds)
/* Clear link settings and enable force mode to force link down
* on all ports until they're enabled later.
*/
- mt7530_rmw(priv, MT753X_PMCR_P(i), PMCR_LINK_SETTINGS_MASK |
- MT7531_FORCE_MODE_MASK, MT7531_FORCE_MODE_MASK);
+ mt7530_rmw(priv, MT753X_PMCR_P(i),
+ PMCR_LINK_SETTINGS_MASK |
+ MT753X_FORCE_MODE(priv->id),
+ MT753X_FORCE_MODE(priv->id));
/* Disable forwarding by default on all ports */
mt7530_rmw(priv, MT7530_PCR_P(i), PCR_MATRIX_MASK,
diff --git a/drivers/net/dsa/mt7530.h b/drivers/net/dsa/mt7530.h
index 28592123070b..d47d1ce511ba 100644
--- a/drivers/net/dsa/mt7530.h
+++ b/drivers/net/dsa/mt7530.h
@@ -355,6 +355,10 @@ enum mt7530_vlan_port_acc_frm {
MT7531_FORCE_MODE_TX_FC | \
MT7531_FORCE_MODE_EEE100 | \
MT7531_FORCE_MODE_EEE1G)
+#define MT753X_FORCE_MODE(id) ((id == ID_MT7531 || \
+ id == ID_MT7988) ? \
+ MT7531_FORCE_MODE_MASK : \
+ MT7530_FORCE_MODE)
#define PMCR_LINK_SETTINGS_MASK (PMCR_MAC_TX_EN | PMCR_MAC_RX_EN | \
PMCR_FORCE_EEE1G | \
PMCR_FORCE_EEE100 | \
+
static struct phylink_pcs *
mt753x_phylink_mac_select_pcs(struct phylink_config *config,
phy_interface_t interface)
@@ -2880,7 +2898,8 @@ mt753x_phylink_mac_config(struct phylink_config *config, unsigned int mode,
priv = ds->priv;
- if ((port == 5 || port == 6) && priv->info->mac_port_config)
+ if ((port == 5 || port == 6 || priv->id == ID_EN7581) &&
+ priv->info->mac_port_config)
priv->info->mac_port_config(ds, port, mode, state->interface);
/* Are we connected to external phy */
@@ -3220,6 +3239,17 @@ const struct mt753x_info mt753x_table[] = {
.phy_write_c45 = mt7531_ind_c45_phy_write,
.mac_port_get_caps = mt7988_mac_port_get_caps,
},
+ [ID_EN7581] = {
+ .id = ID_EN7581,
+ .pcs_ops = &mt7530_pcs_ops,
+ .sw_setup = mt7988_setup,
+ .phy_read_c22 = mt7531_ind_c22_phy_read,
+ .phy_write_c22 = mt7531_ind_c22_phy_write,
+ .phy_read_c45 = mt7531_ind_c45_phy_read,
+ .phy_write_c45 = mt7531_ind_c45_phy_write,
+ .mac_port_get_caps = mt7988_mac_port_get_caps,
+ .mac_port_config = en7581_mac_config,
+ },
Let me lend a hand; you can apply this diff on top of this patch.
diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
index b18b98a53a7d..f5766d8ae360 100644
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -2768,6 +2768,28 @@ static void mt7531_mac_port_get_caps(struct dsa_switch *ds, int port,
static void mt7988_mac_port_get_caps(struct dsa_switch *ds, int port,
struct phylink_config *config)
+{
+ switch (port) {
+ /* Ports which are connected to switch PHYs. There is no MII pinout. */
+ case 0 ... 3:
+ __set_bit(PHY_INTERFACE_MODE_INTERNAL,
+ config->supported_interfaces);
+
+ config->mac_capabilities |= MAC_10 | MAC_100 | MAC_1000FD;
+ break;
+
+ /* Port 6 is connected to SoC's XGMII MAC. There is no MII pinout. */
+ case 6:
+ __set_bit(PHY_INTERFACE_MODE_INTERNAL,
+ config->supported_interfaces);
+
+ config->mac_capabilities |= MAC_10000FD;
+ break;
+ }
+}
+
+static void en7581_mac_port_get_caps(struct dsa_switch *ds, int port,
+ struct phylink_config *config)
{
switch (port) {
/* Ports which are connected to switch PHYs. There is no MII pinout. */
@@ -2855,23 +2877,6 @@ mt7531_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
}
}
-static void
-en7581_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
- phy_interface_t interface)
-{
- /* BIT(31-27): reserved
- * BIT(26): TX_CRC_EN: enable(0)/disable(1) CRC insertion
- * BIT(25): RX_CRC_EN: enable(0)/disable(1) CRC insertion
- * Since the bits above have a different meaning with respect to the
- * one described in mt7530.h, set default values.
- */
- mt7530_clear(ds->priv, MT753X_PMCR_P(port), MT7531_FORCE_MODE_MASK);
- if (dsa_is_cpu_port(ds, port)) {
- /* enable MT7530_FORCE_MODE on cpu port */
- mt7530_set(ds->priv, MT753X_PMCR_P(port), MT7530_FORCE_MODE);
- }
-}
-
static struct phylink_pcs *
mt753x_phylink_mac_select_pcs(struct phylink_config *config,
phy_interface_t interface)
@@ -2902,8 +2907,7 @@ mt753x_phylink_mac_config(struct phylink_config *config, unsigned int mode,
priv = ds->priv;
- if ((port == 5 || port == 6 || priv->id == ID_EN7581) &&
- priv->info->mac_port_config)
+ if ((port == 5 || port == 6) && priv->info->mac_port_config)
priv->info->mac_port_config(ds, port, mode, state->interface);
/* Are we connected to external phy */
@@ -3251,8 +3255,7 @@ const struct mt753x_info mt753x_table[] = {
.phy_write_c22 = mt7531_ind_c22_phy_write,
.phy_read_c45 = mt7531_ind_c45_phy_read,
.phy_write_c45 = mt7531_ind_c45_phy_write,
- .mac_port_get_caps = mt7988_mac_port_get_caps,
- .mac_port_config = en7581_mac_config,
+ .mac_port_get_caps = en7581_mac_port_get_caps,
},
};
EXPORT_SYMBOL_GPL(mt753x_table);
I don't know this hardware so please make sure the comments on
en7581_mac_port_get_caps() are correct. I didn't compile this so please
make sure it works.
By the way, is this supposed to be AN7581? There's EN7580 but no EN7581 on
the Airoha website.
https://www.airoha.com/products/y1cQz8EpjIKhbK61
Arınç
