On Tue, Jul 30, 2024 at 2:14 AM Nícolas F. R. A. Prado <nfraprado@xxxxxxxxxxxxx> wrote: > > On Mon, Jul 29, 2024 at 02:34:27PM +0200, AngeloGioacchino Del Regno wrote: > > Il 29/07/24 12:48, Chen-Yu Tsai ha scritto: > > > On Mon, Jul 29, 2024 at 4:54 PM AngeloGioacchino Del Regno > > > <angelogioacchino.delregno@xxxxxxxxxxxxx> wrote: > > > > > > > > Il 29/07/24 10:07, Chen-Yu Tsai ha scritto: > > > > > On Mon, Jul 29, 2024 at 3:59 PM AngeloGioacchino Del Regno > > > > > <angelogioacchino.delregno@xxxxxxxxxxxxx> wrote: > > > > > > > > > > > > Il 26/07/24 17:11, Chen-Yu Tsai ha scritto: > > > > > > > On Fri, Jul 26, 2024 at 8:11 PM AngeloGioacchino Del Regno > > > > > > > <angelogioacchino.delregno@xxxxxxxxxxxxx> wrote: > > > > > > > > > > > > > > > > Il 25/07/24 12:34, Chen-Yu Tsai ha scritto: > > > > > > > > > Hi, > > > > > > > > > > > > > > > > > > On Mon, Jul 22, 2024 at 11:27 PM Nícolas F. R. A. Prado > > > > > > > > > <nfraprado@xxxxxxxxxxxxx> wrote: > > > > > > > > > > > > > > > > > > > > Currently if the xhci1 controller happens to probe before the pcie1 > > > > > > > > > > controller then it fails with the following errors: > > > > > > > > > > > > > > > > > > > > xhci-mtk 11290000.usb: clocks are not stable (0x1003d0f) > > > > > > > > > > xhci-mtk 11290000.usb: can't setup: -110 > > > > > > > > > > xhci-mtk: probe of 11290000.usb failed with error -110 > > > > > > > > > > > > > > > > > > > > The issue has been tracked down to the CLK_INFRA_AO_PCIE_P1_TL_96M > > > > > > > > > > clock, although exactly why this pcie clock is needed for the usb > > > > > > > > > > controller is still unknown. Add the clock to the xhci1 controller so it > > > > > > > > > > always probes successfully and use a placeholder clock name for it. > > > > > > > > > > > > > > > > > > > > Reported-by: Nícolas F. R. A. Prado <nfraprado@xxxxxxxxxxxxx> #KernelCI > > > > > > > > > > Closes: https://lore.kernel.org/all/9fce9838-ef87-4d1b-b3df-63e1ddb0ec51@notapiano/ > > > > > > > > > > Signed-off-by: Nícolas F. R. A. Prado <nfraprado@xxxxxxxxxxxxx> > > > > > > > > > > > > > > > > > > So I asked MediaTek about this, and it seems the correct thing to do is > > > > > > > > > disable USB 3 on this host controller using the following snippet. The > > > > > > > > > snippet is copy-pasted from our issue tracker and won't apply directly. > > > > > > > > > > > > > > > > > > This is also seen in mt8395-kontron-3-5-sbc-i1200.dts, on which xhci1 > > > > > > > > > is used only for USB 2.0 on an M.2 slot. > > > > > > > > > > > > > > > > > > > > > > > > > Uhm, okay, but why should USB3 be disabled on a controller that supports USB3? > > > > > > > > > > > > > > > > I agree about disabling it on specific boards that use only the USB 2.0 lines of > > > > > > > > this controller, but doing that globally looks wrong... and looks like being a > > > > > > > > workaround for an error that gets solved with adding a clock as well. > > > > > > > > > > > > > > > > In short, the question is: why would that be the correct thing to do? > > > > > > > > > > > > > > We can disable it in mt8195-cherry.dtsi then? > > > > > > > > > > > > That device does not use this controller, so yes we can disable it, but that still > > > > > > doesn't resolve the issue pointed out by Nicolas...! > > > > > > > > > > No. I mean disable USB3 on this port. Also see the next paragraph. > > > > > > > > > > > > > Yes, sorry I was meaning the same - but I effectively wrote "disable controller" > > > > instead, my bad. > > > > > > > > > > Please note that the issue that he sees doesn't happen only on Tomato, but also on > > > > > > other MediaTek MT8195/MT8395 boards - and applying this commit makes disabling the > > > > > > controller, or disabling the USB 3 lines on the controller, kinda redundant, as > > > > > > this will effectively fix probing it... but again, fixing the actual issue with > > > > > > this controller is something that must be done. > > > > > > > > > > If those other boards use the XHCI1 USB3 lines for ... USB3, then the USB3 > > > > > PHY should also be tied to XHCI1, right now due to the Cherry Chromebook > > > > > design, only the USB2 PHY is tied to it. > > > > > > > > > > > > > Yes, I am aware of that. > > > > > > > > > > Disabling the controller on Tomato is a different topic - here we are discussing > > > > > > about fixing the issue, and that will happen, again, on any board that has this > > > > > > controller enabled with USB3 lines. :-) > > > > > > > > > > > > So, unless there is any specific reason for which applying this commit is a bad > > > > > > idea, or any alternative fix to this that is better than the proposed one, and > > > > > > not a workaround... I'm applying this one. > > > > > > > > > > Didn't I just relay what MediaTek says is the correct fix? Disable USB3 > > > > > for this port on devices where the serial pairs are used for PCIe instead > > > > > of USB3. > > > > > > > > > > > > > I think there must've been some misunderstanding here. > > > > > > > > Yes you did relay what MediaTek is the correct fix, and I agree that the USB3 must > > > > be disabled on devices where those serial pairs are used for PCIe instead of USB, > > > > or on devices where those are completely unused. > > > > > > OK. I will send a patch for Tomato as you asked. > > > > > > > This, though, will fix the issue only on those devices (because we are disabling > > > > those lines entirely, so depending on how we see it, this might not be a fix but > > > > rather a workaround). > > > > > > I would say that is a more accurate description of the hardware, so a fix. > > > > > > > I can accept a patch for Tomato with a Fixes tag. Yes. > > > > > > If we don't apply this fix, any board that uses those pairs for USB 3 instead will > > > > still show the same "clocks are not stable" error, leaving them with a broken port. > > > > > > > > And I believe that because the clocks are not routed externally but rather are > > > > internal to the SoC, so, if INFRA_AO_PCIE_P1_TL_96M is necessary for that USB 3 > > > > port to work, a board that intends to use those pairs for USB3 would still need > > > > this exact clock to actually get that port to work. > > > > > > I couldn't reproduce the issue by disabling pcie1 as Nicolas mentioned. > > > I don't have any more to add to this though. Sorry for the noise. > > Huh, that's surprising. FWIW I just reproduced with kernel next-20240729, > upstream defconfig (besides a CONFIG_USB_ONBOARD_DEV=n to be able to boot from > my USB drive), and the pcie1 node in mt8195-cherry.dtsi disabled. Hardware is > mt8195-cherry-tomato-r2. > > Also, I just tested adding > > diff --git a/arch/arm64/boot/dts/mediatek/mt8195-cherry.dtsi b/arch/arm64/boot/dts/mediatek/mt8195-cherry.dtsi > index fe5400e17b0f..a60c4d1419df 100644 > --- a/arch/arm64/boot/dts/mediatek/mt8195-cherry.dtsi > +++ b/arch/arm64/boot/dts/mediatek/mt8195-cherry.dtsi > @@ -1401,6 +1401,7 @@ &xhci0 { > &xhci1 { > status = "okay"; > > + mediatek,u3p-dis-msk = <0x1>; > rx-fifo-depth = <3072>; > vusb33-supply = <&mt6359_vusb_ldo_reg>; > vbus-supply = <&usb_vbus>; > > And that fixed the issue as well. So as far as fixing the error on Tomato, this > patch works too, and makes more sense. Could you also try adding the USB3 PHY instead of disabling U3 on the controller? As: diff --git a/arch/arm64/boot/dts/mediatek/mt8195.dtsi b/arch/arm64/boot/dts/mediatek/mt8195.dtsi index 2ee45752583c..61b3c202a8cd 100644 --- a/arch/arm64/boot/dts/mediatek/mt8195.dtsi +++ b/arch/arm64/boot/dts/mediatek/mt8195.dtsi @@ -1444,7 +1444,7 @@ xhci1: usb@11290000 { <0 0x11293e00 0 0x0100>; reg-names = "mac", "ippc"; interrupts = <GIC_SPI 530 IRQ_TYPE_LEVEL_HIGH 0>; - phys = <&u2port1 PHY_TYPE_USB2>; + phys = <&u2port1 PHY_TYPE_USB2>, <&u3port1 PHY_TYPE_USB3>; assigned-clocks = <&topckgen CLK_TOP_USB_TOP_1P>, <&topckgen CLK_TOP_SSUSB_XHCI_1P>; assigned-clock-parents = <&topckgen CLK_TOP_UNIVPLL_D5_D4>, I wanted to test this, but I couldn't actually reproduce the error. > However I agree with Angelo that a board that does use USB3 on this controller > would still need the original patch adding the PCIE clock to work. But such a > board doesn't currently exist, does it? And we don't actually know if USB3 > really works in that case. Or why this clock is needed. So there are a few > unknowns... MacPaul seems to have one. He mentioned to me that he doesn't need the patch adding the PCIE clock, but needs "mediatek,force-mode" instead. Looking at the comments around "mediatek,force-mode" in the driver, it seems that the PHY defaults to PCIe mode. A combination of not initializing the PHY to USB3 and turning on the PCIe related clock might be what is allowing the PHY to respond to the controller? This is just a guess though. > Anyway, I really don't know what option would be better. Just let me know if I > should resend a patch or CC me in any alternative patch. I'll send the patches to fix up pure USB2 usage. Given we have conflicting reports on whether the PCIe clock is needed, I ask that you try the PHY assignment change first. Thanks ChenYu > Thanks, > Nícolas > > > > > > > > Sometimes the noise actually opens some eyes around (be it mine or whoever else's), > > so as long as it is constructive, I don't see it as noise. > > > > In short: no worries! :-) > > > > > > As for Tomato itself - I agree that we must add the u3p-dis-msk=0x1 flag, yes, > > > > and we will, but I'm purely talking about - again - an eventual board that would > > > > not have that property because USB3 is exposed/used for real. > > > > > > I think it would make more sense to fix the `phys = ` statement in mt8195.dtsi > > > to list both the USB2 and USB3 PHYs. At the board level, for boards only > > > using USB2, we would have the overriding `phys = ` statement alongside the > > > `mediatek,u3p-dis-mask` property. Does that make sense to you? > > > > > > > Yeah, that'd make sense, though I'm not sure if the driver can cope with that: in > > that case, we'd obviously need "two" patches and not one :-) > > > > Cheers! > > > > > > > > Thanks > > > ChenYu > > > > > > > Cheers, > > > > Angelo > > > > > > > > > > > > > > Regards > > > > > ChenYu > > > > > > > > > > > Cheers, > > > > > > Angelo > > > > > > > > > > > > > > > > > > > > ChenYu > > > > > > > > > > > > > > > Cheers, > > > > > > > > Angelo > > > > > > > > > > > > > > > > > > > > > > > > > > ChenYu > > > > > > > > > > > > > > > > > > index 8b7307cdefc6..2dac9f706a58 > > > > > > > > > --- a/arch/arm64/boot/dts/mediatek/mt8195.dtsi > > > > > > > > > +++ b/arch/arm64/boot/dts/mediatek/mt8195.dtsi > > > > > > > > > @@ -1447,6 +1447,7 @@ > > > > > > > > > "xhci_ck"; > > > > > > > > > mediatek,syscon-wakeup = <&pericfg 0x400 104>; > > > > > > > > > wakeup-source; > > > > > > > > > + mediatek,u3p-dis-msk = <0x1>; > > > > > > > > > status = "disabled"; > > > > > > > > > }; > > > > > > > > > > > > > > > > > > > --- > > > > > > > > > > arch/arm64/boot/dts/mediatek/mt8195.dtsi | 10 ++++++++-- > > > > > > > > > > 1 file changed, 8 insertions(+), 2 deletions(-) > > > > > > > > > > > > > > > > > > > > diff --git a/arch/arm64/boot/dts/mediatek/mt8195.dtsi b/arch/arm64/boot/dts/mediatek/mt8195.dtsi > > > > > > > > > > index 2ee45752583c..cc5169871f1c 100644 > > > > > > > > > > --- a/arch/arm64/boot/dts/mediatek/mt8195.dtsi > > > > > > > > > > +++ b/arch/arm64/boot/dts/mediatek/mt8195.dtsi > > > > > > > > > > @@ -1453,9 +1453,15 @@ xhci1: usb@11290000 { > > > > > > > > > > <&topckgen CLK_TOP_SSUSB_P1_REF>, > > > > > > > > > > <&apmixedsys CLK_APMIXED_USB1PLL>, > > > > > > > > > > <&clk26m>, > > > > > > > > > > - <&pericfg_ao CLK_PERI_AO_SSUSB_1P_XHCI>; > > > > > > > > > > + <&pericfg_ao CLK_PERI_AO_SSUSB_1P_XHCI>, > > > > > > > > > > + /* > > > > > > > > > > + * This clock is required due to a hardware > > > > > > > > > > + * bug. The 'frmcnt_ck' clock name is used as a > > > > > > > > > > + * placeholder. > > > > > > > > > > + */ > > > > > > > > > > + <&infracfg_ao CLK_INFRA_AO_PCIE_P1_TL_96M>; > > > > > > > > > > clock-names = "sys_ck", "ref_ck", "mcu_ck", "dma_ck", > > > > > > > > > > - "xhci_ck"; > > > > > > > > > > + "xhci_ck", "frmcnt_ck"; > > > > > > > > > > mediatek,syscon-wakeup = <&pericfg 0x400 104>; > > > > > > > > > > wakeup-source; > > > > > > > > > > status = "disabled"; > > > > > > > > > > > > > > > > > > > > --- > > > > > > > > > > base-commit: dee7f101b64219f512bb2f842227bd04c14efe30 > > > > > > > > > > change-id: 20240722-usb-1129-probe-pci-clk-fix-ef8646f46aac > > > > > > > > > > > > > > > > > > > > Best regards, > > > > > > > > > > -- > > > > > > > > > > Nícolas F. R. A. Prado <nfraprado@xxxxxxxxxxxxx> > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > >
