On Sat Jun 29, 2024 at 6:39 PM CEST, Jonathan Cameron wrote:
> On Thu, 27 Jun 2024 13:59:13 +0200
> Esteban Blanc <eblanc@xxxxxxxxxxxx> wrote:
>
> > This adds a new driver for the Analog Devices INC. AD4030-24 ADC.
> >
> > The driver implements basic support for the AD4030-24 1 channel
> > differential ADC with hardware gain and offset control.
> >
> > Signed-off-by: Esteban Blanc <eblanc@xxxxxxxxxxxx>
...
> > +static int ad4030_spi_read(void *context, const void *reg, size_t reg_size,
> > + void *val, size_t val_size)
> > +{
> > + struct ad4030_state *st = context;
> > +
> > + struct spi_transfer xfer = {
> > + .tx_buf = st->tx_data,
> > + .rx_buf = st->rx_data.raw,
> > + .len = reg_size + val_size,
> > + };
> > + int ret;
> > +
> > + memcpy(st->tx_data, reg, reg_size);
> > +
> > + ret = spi_sync_transfer(st->spi, &xfer, 1);
> > + if (ret)
> > + return ret;
> > +
> > + memcpy(val, &st->rx_data.raw[reg_size], val_size);
>
> Can you just use spi_write_then_read() here?
>
I was planning on doing that. But I'm getting a timeout issue when
using `spi_write_then_read`. I can see the tx_data going out, rx_data
is recived but CS is kept asserted. I need to investigate more but in
the meantime I'm using this as it is working. I will remove this
workaround if I can find a fix and add a comment for now.
> > + if (ret)
> > + return ret;
> > +
> > + if (st->chip->precision_bits == 16)
> > + offset <<= 16;
> > + else
> > + offset <<= 8;
>
> As below. This is hard tor read. Just use appropriate unaligned gets for the
> two cases to extract the write bytes directly.
>
> > + *val = be32_to_cpu(offset);
> > +
> > + return 0;
> > +}
> > +
> > +static int ad4030_set_chan_gain(struct iio_dev *indio_dev, int ch, int gain_int,
> > + int gain_frac)
> > +{
> > + struct ad4030_state *st = iio_priv(indio_dev);
> > + __be16 val;
> > + u64 gain;
> > +
> > + gain = mul_u32_u32(gain_int, MICRO) + gain_frac;
> > +
> > + if (gain > AD4030_REG_GAIN_MAX_GAIN)
> > + return -EINVAL;
> > +
> > + val = cpu_to_be16(DIV_ROUND_CLOSEST_ULL(gain * 0x8000, MICRO));
> > +
> > + return regmap_bulk_write(st->regmap, AD4030_REG_GAIN_CHAN(ch), &val,
> > + AD4030_REG_GAIN_BYTES_NB);
> > +}
> > +
> > +static int ad4030_set_chan_offset(struct iio_dev *indio_dev, int ch, int offset)
> > +{
> > + struct ad4030_state *st = iio_priv(indio_dev);
> > + __be32 val;
> > +
> > + if (offset < st->min_offset || offset > st->max_offset)
> > + return -EINVAL;
> > +
> > + val = cpu_to_be32(offset);
> > + if (st->chip->precision_bits == 16)
> > + val >>= 16;
> > + else
> > + val >>= 8;
>
> I 'think' I get what this is doing but not 100% sure as it's a bit too unusual
> and I'm not even sure what happens if we shift a __be32 value on a little endian
> system. I would instead split this into appropriate cpu_to_be24() and cpu_to_be16()
> to put the value directly in the right place rather than shifting in place.
cpu_to_be24 does not exist yet. I will have a look on how to add them.
All the other comments will be addressed in V2.
Best regards,
--
Esteban "Skallwar" Blanc
BayLibre
