This implements a set of drivers for the MCU used on QNAP NAS devices.
Of course no documentation for the serial protocol is available, so
thankfully QNAP has a tool on their rescue-inird to talk to the MCU and
I found interceptty [0] to listen to what goes over the serial connection.
In general it looks like there are two different generations in general,
an "EC" device and now this "MCU" - referenced in the strings of the
userspace handlers for those devices.
For the MCU "SPEC3" and "SPEC4" are listed which is configured in
the model.conf of the device. When setting the value from SPEC4 to
SPEC3 on my TS433, the supported commands change, but the command
interface stays the same and especially the version command is the
same.
The binding also does not expose any interals of the device that
might change, so hopefully there shouldn't be big roadblocks to
support different devices, apart from possibly adapting the commands.
changes in v2:
binding:
- rename to qnap,ts433-mcu.yaml (Krzysztof)
- drop "preserve formatting" indicator (Krzysztof)
- add Krzysztof's Review tag
mfd:
- fix checkpatch --strict CHECKs
- add a MAINTAINERS entry for all qnap-mcu-parts
hwmon:
address Guenter's review comments:
- fix checkpatch strict warnings
I've kept the devm_thermal_of_cooling_device_register alignment,
because that line is so long that aligning to the "(" would make
things way too long and unreadable
- add hwmon documentation
- spelling corrections
- report actual pwm value, not last-set one
- make some cmd arrays static
- drop pwm_enable as the pwm-mode is not controllable
- actually handle error returns from mcu commands
- fix calculation of fan-rpm (I read my notes wrong)
- fix temperature calculation to return millicelsius as expected
- only bail at obviously wrong pwm values, but clamp to min,max
- only register cooling-device if cooling-levels are available
[0] https://github.com/geoffmeyers/interceptty
Heiko Stuebner (7):
dt-bindings: mfd: add binding for qnap,ts433-mcu devices
mfd: add base driver for qnap-mcu devices
leds: add driver for LEDs from qnap-mcu devices
Input: add driver for the input part of qnap-mcu devices
hwmon: add driver for the hwmon parts of qnap-mcu devices
arm64: dts: rockchip: hook up the MCU on the QNAP TS433
arm64: dts: rockchip: set hdd led labels on qnap-ts433
.../bindings/mfd/qnap,ts433-mcu.yaml | 43 ++
Documentation/hwmon/index.rst | 1 +
Documentation/hwmon/qnap-mcu-hwmon.rst | 27 ++
MAINTAINERS | 9 +
.../boot/dts/rockchip/rk3568-qnap-ts433.dts | 58 +++
drivers/hwmon/Kconfig | 12 +
drivers/hwmon/Makefile | 1 +
drivers/hwmon/qnap-mcu-hwmon.c | 375 ++++++++++++++++++
drivers/input/misc/Kconfig | 12 +
drivers/input/misc/Makefile | 1 +
drivers/input/misc/qnap-mcu-input.c | 156 ++++++++
drivers/leds/Kconfig | 11 +
drivers/leds/Makefile | 1 +
drivers/leds/leds-qnap-mcu.c | 247 ++++++++++++
drivers/mfd/Kconfig | 10 +
drivers/mfd/Makefile | 2 +
drivers/mfd/qnap-mcu.c | 358 +++++++++++++++++
include/linux/mfd/qnap-mcu.h | 28 ++
18 files changed, 1352 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/qnap,ts433-mcu.yaml
create mode 100644 Documentation/hwmon/qnap-mcu-hwmon.rst
create mode 100644 drivers/hwmon/qnap-mcu-hwmon.c
create mode 100644 drivers/input/misc/qnap-mcu-input.c
create mode 100644 drivers/leds/leds-qnap-mcu.c
create mode 100644 drivers/mfd/qnap-mcu.c
create mode 100644 include/linux/mfd/qnap-mcu.h
--
2.39.2
