This patchset contains the pinmux (IOMUX) and GPIO/PINCONF support for
Broadcom Cygnus SoC.
The Cygnus IOMUX controller supports group based mux
configuration and allows certain pins to be muxed to GPIO function
individually. The IOMUX controller is supported by the pinctrl-cygnus-mux.c
driver.
Cygnus has 3 GPIO controllers: 1) the ASIU GPIO; 2) the chipCommonG GPIO;
and 3) the ALWAYS-ON GPIO. All 3 Cygnus GPIO controllers support basic PINCONF
functions such as bias pull up, pull down, and drive strength configuration,
when pins are muxed to GPIO. GPIO/PINCONF support is in the
pinctrl-cygnus-gpio.c driver.
Note pins from the ASIU GPIO can be individually muxed to GPIO function,
through interaction with the Cygnus IOMUX controller.
Changes from v5:
- Remove ngpios device tree property. Instead, determine the number of GPIO
based on compaitble string in the driver
- Remove all MODULE_* related macros in the driver since the driver will never
be compiled as a kernel loadable module
Changes from v4:
- Rebased to Linux 4.0-rc2
- Switched to use the newly available pinconf_generic_dt_node_to_map_group
function for mapping DT mux properties in the IOMUX driver. This helps
to get rid of customized device tree parsing code in the driver
- Consolidated the other Cygnus GPIO/PINCONF patchset into one single patchset
- Tuned up the GPIO/PINCONF driver a bit more, based on code review comments
from Linus Walleij
Changes from v3:
- Fix the driver to have more proper use of "const" in various places
- Other minor improvements
Changes from v2:
- Consolidate all Broadcom pinctrl drivers into drivers/pinctrl/bcm/*
- Change the Cygnus IOMUX driver to use standard Linux pinctrl subnode
properties such as "function" and "groups" for pinmux configuration, instead
of non-standard properties such as "brcm,function" and "brcm,group"
- Use real function names like "spi0", "lcd", "key", and etc. instead of HW
specific mux names like "alt1", "alt2", "alt3", and etc.
- Add suffix "grp" to all group names
- Add support to allow individual pins to be muxed to GPIO function through
subsystem callbacks "gpio_request_enable" and "gpio_disable_free", and get rid
of all GPIO groups
- Other minor improvements in the driver
Changes from v1:
- Fix a typo in device tree binding document
Ray Jui (8):
pinctrl: bcm: consolidate Broadcom pinctrl drivers
pinctrl: Broadcom Cygnus pinctrl device tree binding
pinctrl: cygnus: add initial IOMUX driver support
ARM: dts: enable IOMUX for Broadcom Cygnus
pinctrl: Cygnus: define Broadcom Cygnus GPIO/PINCONF binding
pinctrl: cygnus: add gpio/pinconf driver
ARM: dts: enable GPIO for Broadcom Cygnus
ARM: dts: cygnus: enable GPIO based hook detection
.../bindings/pinctrl/brcm,cygnus-gpio.txt | 98 ++
.../bindings/pinctrl/brcm,cygnus-pinmux.txt | 132 +++
arch/arm/boot/dts/bcm-cygnus.dtsi | 36 +
arch/arm/boot/dts/bcm911360_entphn.dts | 13 +
drivers/pinctrl/Kconfig | 19 +-
drivers/pinctrl/Makefile | 3 +-
drivers/pinctrl/bcm/Kconfig | 56 ++
drivers/pinctrl/bcm/Makefile | 6 +
drivers/pinctrl/{ => bcm}/pinctrl-bcm281xx.c | 4 +-
drivers/pinctrl/{ => bcm}/pinctrl-bcm2835.c | 0
drivers/pinctrl/bcm/pinctrl-cygnus-gpio.c | 907 +++++++++++++++++
drivers/pinctrl/bcm/pinctrl-cygnus-mux.c | 1017 ++++++++++++++++++++
12 files changed, 2269 insertions(+), 22 deletions(-)
create mode 100644 Documentation/devicetree/bindings/pinctrl/brcm,cygnus-gpio.txt
create mode 100644 Documentation/devicetree/bindings/pinctrl/brcm,cygnus-pinmux.txt
create mode 100644 drivers/pinctrl/bcm/Kconfig
create mode 100644 drivers/pinctrl/bcm/Makefile
rename drivers/pinctrl/{ => bcm}/pinctrl-bcm281xx.c (99%)
rename drivers/pinctrl/{ => bcm}/pinctrl-bcm2835.c (100%)
create mode 100644 drivers/pinctrl/bcm/pinctrl-cygnus-gpio.c
create mode 100644 drivers/pinctrl/bcm/pinctrl-cygnus-mux.c
--
1.7.9.5
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
