This adds support for Freescale NAND flash controller (NFC) found on various devices such as Vybrid (VF610), MPC5125, MCF54418 (ColdFire) and Kinetis K70. The patchset is based on the patchset by Bill Pringlemeir, see: http://thread.gmane.org/gmane.linux.ports.arm.kernel/295419 A variant of this driver is in upstream U-Boot now. During this process, various points have been discussed and changed. Those changes are also incorporated in this patchset, including the change to the name "vf610_nfc" (discussion in first patchset). http://thread.gmane.org/gmane.comp.boot-loaders.u-boot/192465 http://thread.gmane.org/gmane.comp.boot-loaders.u-boot/193142 http://thread.gmane.org/gmane.comp.boot-loaders.u-boot/193351 http://thread.gmane.org/gmane.comp.boot-loaders.u-boot/195441 http://thread.gmane.org/gmane.comp.boot-loaders.u-boot/195513 MTD tests worked, except mtd_nandecctest.ko: The test stopped already after changing the first bit. I guess this is due to not properly working raw page read/write implementation. However, implementing those functions is not feasible since ECC is always done on-the-fly. Performance keypoints (slightly less for page write/reads): [ 1782.284398] mtd_speedtest: testing eraseblock write speed [ 1963.472907] mtd_speedtest: eraseblock write speed is 2877 KiB/s [ 1963.478913] mtd_speedtest: testing eraseblock read speed [ 2004.906267] mtd_speedtest: eraseblock read speed is 12586 KiB/s The driver has only been tested on Freescale Vybrid. Tests on other platforms welcome, especially on big endian architectures... Changes since v1: - Nest nfc_config struct within the main nfc struct - Use assigned clock binding to specify NFC clock - Rebased ontop of MSCM IR patchset (driver parts have been merged) - Split out arch Kconfig in a seperate config - Fix module license - Updated MAINTAINERS Changes since RFC (Bill Pringlemeir): - Renamed driver from fsl_nfc to vf610_nfc - Use readl/writel for all register in accessor functions - Optimized field accessor functions - Implemented PM (suspend/resume) functions - Implemented basic support for ECC strength/ECC step size from dt - Improved performance of count_written_bits by using hweight32 - Support ECC with 60-bytes to correct up to 32 bit errors - Changed to in-band BBT (NAND_BBT_NO_OOB) which also allows ECC modes which uses up to 60 bytes on 64 byte OOB - Removed custom (downstream) BBT pattern since BBT table won't be compatible anyway (due to the change above) Stefan Agner (6): mtd: nand: vf610_nfc: Freescale NFC for VF610, MPC5125 and others mtd: nand: vf610_nfc: add hardware BCH-ECC support mtd: nand: vf610_nfc: add device tree bindings ARM: vf610: enable NAND Flash Controller ARM: dts: vf610: add NAND flash controller peripherial ARM: dts: vf-colibri: enable NAND flash controller .../devicetree/bindings/mtd/vf610-nfc.txt | 39 + MAINTAINERS | 6 + arch/arm/boot/dts/vf-colibri.dtsi | 32 + arch/arm/boot/dts/vf610-twr.dts | 44 ++ arch/arm/boot/dts/vfxxx.dtsi | 8 + arch/arm/mach-imx/Kconfig | 1 + drivers/mtd/nand/Kconfig | 14 + drivers/mtd/nand/Makefile | 1 + drivers/mtd/nand/vf610_nfc.c | 856 +++++++++++++++++++++ 9 files changed, 1001 insertions(+) create mode 100644 Documentation/devicetree/bindings/mtd/vf610-nfc.txt create mode 100644 drivers/mtd/nand/vf610_nfc.c -- 2.3.1 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
