On Sat, Jul 20, 2024 at 12:37:27PM +0100, Jonathan Cameron wrote:
> On Thu, 11 Jul 2024 23:15:57 +0200
> Vasileios Amoiridis <vassilisamir@xxxxxxxxx> wrote:
>
> > The BMP3xx and BMP5xx sensors have an interrupt pin which can be used as
> > a trigger for when there are data ready in the sensor for pick up.
> >
> > This use case is used along with NORMAL_MODE in the sensor, which allows
> > the sensor to do consecutive measurements depending on the ODR rate value.
> >
> > The trigger pin can be configured to be open-drain or push-pull and either
> > rising or falling edge.
> >
> > No support is added yet for interrupts for FIFO, WATERMARK and out of range
> > values.
> >
> > Signed-off-by: Vasileios Amoiridis <vassilisamir@xxxxxxxxx>
>
> A few minor things inline.
>
> It might be worth thinking a bit about future fifo support as that can
> get a little messy in a driver that already supports a dataready trigger.
> We end up with no trigger being set meaning use the fifo. Sometimes
> it makes more sense to not support triggers at all.
>
> What you have here is fine though as we have a bunch of drivers
> that grew dataready trigger support before adding fifos later
> particularly as often it's a 'new chip' that brings the fifo
> support but maintains backwards compatibility if you don't use it.
>
Hi Jonathan,
Thank you very much for your thorough review again!
What I could do to make the code even better to be able to accept
FIFO irq support are the following:
1) in the bmp{380/580}_trigger_handler() currently, the data registers
are being read. What I could do is to move the reading of registers
to a separe function like bmpxxx_drdy_trigger_handler() and calling
it inside the bmp{380/580}_trigger_handler() when I have DRDY or
sysfs irq. In order to check the enabled irqs I propose also no.2
2) in the following bmp{380/580}_trigger_probe() functions instead of
just doing:
irq = fwnode_irq_get_byname(fwnode, "DRDY");
if (!irq) {
dev_err(data->dev, "No DRDY interrupt found\n");
return -ENODEV;
}
I could also use some type of variable like we do for the active
channels in order to track "active/existing irqs".
Like this it would be easier to track the active irqs of the sensor.
Let me know what you think, or if I manage to have time I might send
a v2 with those changes even earlier :)
Cheers,
Vasilis
> > +
> > +static int bmp380_trigger_probe(struct iio_dev *indio_dev)
> > +{
> > + struct bmp280_data *data = iio_priv(indio_dev);
> > + struct fwnode_handle *fwnode;
> > + int ret, irq, irq_type;
> > + struct irq_data *desc;
> > +
> > + fwnode = dev_fwnode(data->dev);
> > + if (!fwnode)
> > + return -ENODEV;
> > +
> > + irq = fwnode_irq_get_byname(fwnode, "DRDY");
> > + if (!irq) {
> > + dev_err(data->dev, "No DRDY interrupt found\n");
> > + return -ENODEV;
> As below. return dev_err_probe() for anything that is only
> called from probe()
>
> > + }
> > +
> > + desc = irq_get_irq_data(irq);
> > + if (!desc)
> > + return -EINVAL;
> > +
> > + irq_type = irqd_get_trigger_type(desc);
> > + switch (irq_type) {
> > + case IRQF_TRIGGER_RISING:
> > + data->trig_active_high = true;
> > + break;
> > + case IRQF_TRIGGER_FALLING:
> > + data->trig_active_high = false;
> > + break;
> > + default:
> > + dev_err(data->dev, "Invalid interrupt type specified\n");
> > + return -EINVAL;
> > + }
> > +
> > + data->trig_open_drain = fwnode_property_read_bool(fwnode,
> > + "int-open-drain");
> > +
> > + ret = bmp380_int_config(data);
> > + if (ret)
> > + return ret;
> > +
> > + data->trig = devm_iio_trigger_alloc(data->dev, "%s-dev%d",
> > + indio_dev->name,
> > + iio_device_id(indio_dev));
> > + if (!data->trig)
> > + return -ENOMEM;
> > +
> > + data->trig->ops = &bmp380_trigger_ops;
> > + iio_trigger_set_drvdata(data->trig, data);
> > +
> > + ret = devm_request_irq(data->dev, irq,
> > + &iio_trigger_generic_data_rdy_poll,
> > + IRQF_ONESHOT, indio_dev->name, data->trig);
> > + if (ret) {
> > + dev_err(data->dev, "request irq failed\n");
> > + return ret;
> > + }
> > +
> > + ret = devm_iio_trigger_register(data->dev, data->trig);
> > + if (ret) {
> > + dev_err(data->dev, "iio trigger register failed\n");
> > + return ret;
> > + }
> > +
> > + indio_dev->trig = iio_trigger_get(data->trig);
> > +
> > + return 0;
> > +}
> > +
> > +
> One blank line only.
>
> > static irqreturn_t bmp380_trigger_handler(int irq, void *p)
>
>
> > +
> > +static int bmp580_trigger_probe(struct iio_dev *indio_dev)
> > +{
> > + struct bmp280_data *data = iio_priv(indio_dev);
> > + struct fwnode_handle *fwnode;
> > + int ret, irq, irq_type;
> > + struct irq_data *desc;
> > +
> > + fwnode = dev_fwnode(data->dev);
> > + if (!fwnode)
> > + return -ENODEV;
> > +
> > + irq = fwnode_irq_get_byname(fwnode, "DRDY");
> > + if (!irq) {
> > + dev_err(data->dev, "No DRDY interrupt found\n");
>
> As this only gets called from probe(), use return dev_err_probe() throughout.
>
> > + return -ENODEV;
> > + }
> > +
> > + desc = irq_get_irq_data(irq);
> > + if (!desc)
> > + return -EINVAL;
> > +
> > + irq_type = irqd_get_trigger_type(desc);
> > + switch (irq_type) {
> > + case IRQF_TRIGGER_RISING:
> > + data->trig_active_high = true;
> > + break;
> > + case IRQF_TRIGGER_FALLING:
> > + data->trig_active_high = false;
> > + break;
> > + default:
> > + dev_err(data->dev, "Invalid interrupt type specified\n");
> > + return -EINVAL;
> > + }
> > +
> > + data->trig_open_drain = fwnode_property_read_bool(fwnode,
> > + "int-open-drain");
> > +
> > + ret = bmp580_int_config(data);
> > + if (ret)
> > + return ret;
> > +
> > + data->trig = devm_iio_trigger_alloc(data->dev, "%s-dev%d",
> > + indio_dev->name,
> > + iio_device_id(indio_dev));
> > + if (!data->trig)
> > + return -ENOMEM;
> > +
> > + data->trig->ops = &bmp580_trigger_ops;
> > + iio_trigger_set_drvdata(data->trig, data);
> > +
> > + ret = devm_request_irq(data->dev, irq,
> > + &iio_trigger_generic_data_rdy_poll,
> > + IRQF_ONESHOT, indio_dev->name, data->trig);
> > + if (ret) {
> > + dev_err(data->dev, "request irq failed\n");
> > + return ret;
> > + }
> > +
> > + ret = devm_iio_trigger_register(data->dev, data->trig);
> > + if (ret) {
> > + dev_err(data->dev, "iio trigger register failed\n");
> > + return ret;
> > + }
> > +
> > + indio_dev->trig = iio_trigger_get(data->trig);
> > +
> > + return 0;
> > +}
> >
> >
>
