On Thu, Jul 18, 2024 at 06:26:33PM +0800, Xu Yang wrote:
> Per IC engineer request, we need to keep USBPHY2's clk always on,
"IP require keep keep USBPHY2's clk always on."
Not personal request, even it is IC expert. It should base on the "fact"
instead of personal's opinion.
> in this way, the USBPHY2 (PLL7) power can be controlled by
> hardware suspend signal totally. It is benefit of USB remote wakeup
> case which needs the resume signal be sent out as soon as
> possible (without software interfere). Without this, we may see usb
> remote wakeup issue since the host does not send resume in time.
So USBPHY2 (PLL7) power can be controlled by suspend signal. USB remote
wakeup needs resume signal be sent out as soon as possible to match
"spec requirement" or some other requirement.
>
> Signed-off-by: Xu Yang <xu.yang_2@xxxxxxx>
> ---
> drivers/usb/phy/phy-mxs-usb.c | 36 ++++++++++++++++++++++++++++-------
> 1 file changed, 29 insertions(+), 7 deletions(-)
>
> diff --git a/drivers/usb/phy/phy-mxs-usb.c b/drivers/usb/phy/phy-mxs-usb.c
> index 42fcc8ad9492..b6868cc22c1e 100644
> --- a/drivers/usb/phy/phy-mxs-usb.c
> +++ b/drivers/usb/phy/phy-mxs-usb.c
> @@ -150,6 +150,16 @@
> #define MXS_PHY_TX_D_CAL_MIN 79
> #define MXS_PHY_TX_D_CAL_MAX 119
>
> +/*
> + * At some versions, the PHY2's clock is controlled by hardware directly,
It better declear which version, for example, which chip use if no version
info in IP.
> + * eg, according to PHY's suspend status. In these PHYs, we only need to
> + * open the clock at the initialization and close it at its shutdown routine.
> + * It will be benefit for remote wakeup case which needs to send resume
> + * signal as soon as possible, and in this case, the resume signal can be sent
> + * out without software interfere.
These PHYs can send resume signal without software interfere if not gate
clock.
> + */
> +#define MXS_PHY_HARDWARE_CONTROL_PHY2_CLK BIT(4)
> +
> struct mxs_phy_data {
> unsigned int flags;
> };
> @@ -161,12 +171,14 @@ static const struct mxs_phy_data imx23_phy_data = {
> static const struct mxs_phy_data imx6q_phy_data = {
> .flags = MXS_PHY_SENDING_SOF_TOO_FAST |
> MXS_PHY_DISCONNECT_LINE_WITHOUT_VBUS |
> - MXS_PHY_NEED_IP_FIX,
> + MXS_PHY_NEED_IP_FIX |
> + MXS_PHY_HARDWARE_CONTROL_PHY2_CLK,
> };
>
> static const struct mxs_phy_data imx6sl_phy_data = {
> .flags = MXS_PHY_DISCONNECT_LINE_WITHOUT_VBUS |
> - MXS_PHY_NEED_IP_FIX,
> + MXS_PHY_NEED_IP_FIX |
> + MXS_PHY_HARDWARE_CONTROL_PHY2_CLK,
> };
>
> static const struct mxs_phy_data vf610_phy_data = {
> @@ -175,7 +187,8 @@ static const struct mxs_phy_data vf610_phy_data = {
> };
>
> static const struct mxs_phy_data imx6sx_phy_data = {
> - .flags = MXS_PHY_DISCONNECT_LINE_WITHOUT_VBUS,
> + .flags = MXS_PHY_DISCONNECT_LINE_WITHOUT_VBUS |
> + MXS_PHY_HARDWARE_CONTROL_PHY2_CLK,
> };
>
> static const struct mxs_phy_data imx6ul_phy_data = {
> @@ -206,6 +219,7 @@ struct mxs_phy {
> u32 tx_reg_set;
> u32 tx_reg_mask;
> struct regulator *phy_3p0;
> + bool hardware_control_phy2_clk;
Needn't it. just check MXS_PHY_HARDWARE_CONTROL_PHY2_CLK flag is enough.
> };
>
> static inline bool is_imx6q_phy(struct mxs_phy *mxs_phy)
> @@ -518,12 +532,17 @@ static int mxs_phy_suspend(struct usb_phy *x, int suspend)
> }
> writel(BM_USBPHY_CTRL_CLKGATE,
> x->io_priv + HW_USBPHY_CTRL_SET);
> - clk_disable_unprepare(mxs_phy->clk);
> + if (!(mxs_phy->port_id == 1 &&
> + mxs_phy->hardware_control_phy2_clk))
> + clk_disable_unprepare(mxs_phy->clk);
> } else {
> mxs_phy_clock_switch_delay();
> - ret = clk_prepare_enable(mxs_phy->clk);
> - if (ret)
> - return ret;
> + if (!(mxs_phy->port_id == 1 &&
> + mxs_phy->hardware_control_phy2_clk)) {
> + ret = clk_prepare_enable(mxs_phy->clk);
> + if (ret)
> + return ret;
> + }
> writel(BM_USBPHY_CTRL_CLKGATE,
> x->io_priv + HW_USBPHY_CTRL_CLR);
> writel(0, x->io_priv + HW_USBPHY_PWD);
> @@ -819,6 +838,9 @@ static int mxs_phy_probe(struct platform_device *pdev)
> if (mxs_phy->phy_3p0)
> regulator_set_voltage(mxs_phy->phy_3p0, 3200000, 3200000);
>
> + if (mxs_phy->data->flags & MXS_PHY_HARDWARE_CONTROL_PHY2_CLK)
> + mxs_phy->hardware_control_phy2_clk = true;
> +
Needn't it.
> platform_set_drvdata(pdev, mxs_phy);
>
> device_set_wakeup_capable(&pdev->dev, true);
> --
> 2.34.1
>
