Hi Heiko,
On Mon, 15 Jul 2024 at 16:35, Heiko Stuebner <heiko@xxxxxxxxx> wrote:
>
> The Rock 5 ITX uses two PCIe controllers to drive both a M.2 slot and its
> SATA controller with 2 lanes each. The supply for the refclk oscillator is
> the same that supplies the M.2 slot, but the SATA controller port is
> supplied by a different rail.
>
> This leads to the effect that if the PCIe30x4 controller for the M.2
> probes first, everything works normally. But if the PCIe30x2 controller
> that is connected to the SATA controller probes first, it will hang on
> the first DBI read as nothing will have enabled the refclock before.
>
I just checked the rk3588-rock-5-itx.dts in the linux-next.
You have not enabled sata0 and sata2, which might be the problem
for the SATA controller not getting initialized.
Thanks
-Anand
> Fix this by describing the clock generator with its supplies so that
> both controllers can reference it as needed.
>
> Signed-off-by: Heiko Stuebner <heiko@xxxxxxxxx>
> ---
> .../boot/dts/rockchip/rk3588-rock-5-itx.dts | 38 ++++++++++++++++++-
> 1 file changed, 36 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/rockchip/rk3588-rock-5-itx.dts b/arch/arm64/boot/dts/rockchip/rk3588-rock-5-itx.dts
> index d0b922b8d67e8..37bc53f2796fc 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3588-rock-5-itx.dts
> +++ b/arch/arm64/boot/dts/rockchip/rk3588-rock-5-itx.dts
> @@ -72,6 +72,15 @@ hdd-led2 {
> };
> };
>
> + /* Unnamed voltage oscillator: 100MHz,3.3V,3225 */
> + pcie30_port0_refclk: pcie30_port1_refclk: pcie-voltage-oscillator {
> + compatible = "voltage-oscillator";
> + #clock-cells = <0>;
> + clock-frequency = <100000000>;
> + clock-output-names = "pcie30_refclk";
> + vdd-supply = <&vcc3v3_pi6c_05>;
> + };
> +
> fan0: pwm-fan {
> compatible = "pwm-fan";
> #cooling-cells = <2>;
> @@ -146,13 +155,14 @@ vcc3v3_lan: vcc3v3_lan_phy2: regulator-vcc3v3-lan {
> vin-supply = <&vcc_3v3_s3>;
> };
>
> - vcc3v3_mkey: regulator-vcc3v3-mkey {
> + /* The PCIE30x4_PWREN_H controls two regulators */
> + vcc3v3_mkey: vcc3v3_pi6c_05: regulator-vcc3v3-pi6c-05 {
> compatible = "regulator-fixed";
> enable-active-high;
> gpios = <&gpio1 RK_PA4 GPIO_ACTIVE_HIGH>;
> pinctrl-names = "default";
> pinctrl-0 = <&pcie30x4_pwren_h>;
> - regulator-name = "vcc3v3_mkey";
> + regulator-name = "vcc3v3_pi6c_05";
> regulator-min-microvolt = <3300000>;
> regulator-max-microvolt = <3300000>;
> startup-delay-us = <5000>;
> @@ -513,6 +523,18 @@ &pcie30phy {
>
> /* ASMedia ASM1164 Sata controller */
> &pcie3x2 {
> + /*
> + * The board has a "pcie_refclk" oscillator that needs enabling,
> + * so add it to the list of clocks.
> + */
> + clocks = <&cru ACLK_PCIE_2L_MSTR>, <&cru ACLK_PCIE_2L_SLV>,
> + <&cru ACLK_PCIE_2L_DBI>, <&cru PCLK_PCIE_2L>,
> + <&cru CLK_PCIE_AUX1>, <&cru CLK_PCIE2L_PIPE>,
> + <&pcie30_port1_refclk>;
> + clock-names = "aclk_mst", "aclk_slv",
> + "aclk_dbi", "pclk",
> + "aux", "pipe",
> + "ref";
> pinctrl-names = "default";
> pinctrl-0 = <&pcie30x2_perstn_m1_l>;
> reset-gpios = <&gpio4 RK_PB0 GPIO_ACTIVE_HIGH>;
> @@ -522,6 +544,18 @@ &pcie3x2 {
>
> /* M.2 M.key */
> &pcie3x4 {
> + /*
> + * The board has a "pcie_refclk" oscillator that needs enabling,
> + * so add it to the list of clocks.
> + */
> + clocks = <&cru ACLK_PCIE_4L_MSTR>, <&cru ACLK_PCIE_4L_SLV>,
> + <&cru ACLK_PCIE_4L_DBI>, <&cru PCLK_PCIE_4L>,
> + <&cru CLK_PCIE_AUX0>, <&cru CLK_PCIE4L_PIPE>,
> + <&pcie30_port0_refclk>;
> + clock-names = "aclk_mst", "aclk_slv",
> + "aclk_dbi", "pclk",
> + "aux", "pipe",
> + "ref";
> num-lanes = <2>;
> pinctrl-names = "default";
> pinctrl-0 = <&pcie30x4_perstn_m1_l>;
> --
> 2.39.2
>
>
> _______________________________________________
> Linux-rockchip mailing list
> Linux-rockchip@xxxxxxxxxxxxxxxxxxx
> http://lists.infradead.org/mailman/listinfo/linux-rockchip
