Hi Jonas,
On Fri, 12 Jul 2024 at 22:16, Anand Moon <linux.amoon@xxxxxxxxx> wrote:
>
> Add missing pinctrl settings for PCIe 3.0 x4 clock request and wake
> signals. Each component of PCIe communication have the following control
> signals: PERST, WAKE, CLKREQ, and REFCLK. These signals work to generate
> high-speed signals and communicate with other PCIe devices.
> Used by root complex to endpoint depending on the power state.
>
> PERST is referred to as a fundamental reset. PERST should be held low
> until all the power rails in the system and the reference clock are stable.
> A transition from low to high in this signal usually indicates the
> beginning of link initialization.
>
> WAKE signal is an active-low signal that is used to return the PCIe
> interface to an active state when in a low-power state.
>
> CLKREQ signal is also an active-low signal and is used to request the
> reference clock.
>
> Rename node from 'pcie3' to 'pcie30x4' to align with schematic
> nomenclature.
>
> Signed-off-by: Anand Moon <linux.amoon@xxxxxxxxx>
> ---
> V3: use pinctrl local to board
> V2: Update the commit messge to describe the changs.
> use pinctl group as its pre define in pinctrl dtsi
> ---
> .../arm64/boot/dts/rockchip/rk3588-rock-5b.dts | 18 ++++++++++++------
> 1 file changed, 12 insertions(+), 6 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts b/arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts
> index 966bbc582d89..721e87a3a464 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts
> +++ b/arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts
> @@ -338,7 +338,7 @@ &pcie30phy {
>
> &pcie3x4 {
> pinctrl-names = "default";
> - pinctrl-0 = <&pcie3_rst>;
> + pinctrl-0 = <&pcie30x4_pins>;
> reset-gpios = <&gpio4 RK_PB6 GPIO_ACTIVE_HIGH>;
> vpcie3v3-supply = <&vcc3v3_pcie30>;
> status = "okay";
> @@ -377,14 +377,20 @@ pcie2_2_rst: pcie2-2-rst {
> };
> };
>
> - pcie3 {
> - pcie3_rst: pcie3-rst {
> - rockchip,pins = <4 RK_PB6 RK_FUNC_GPIO &pcfg_pull_none>;
> - };
> -
> + pcie30x4 {
> pcie3_vcc3v3_en: pcie3-vcc3v3-en {
> rockchip,pins = <1 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>;
> };
> +
> + pcie30x4_pins: pcie30x4-pins {
> + rockchip,pins =
> + /* PCIE30X4_CLKREQn_M1_L */
> + <4 RK_PB4 4 &pcfg_pull_up>,
Should -------------^ replace with
RK_FUNC_GPIO ? since its a gpio controlled?
> + /* PCIE30X4_PERSTn_M1_L */
> + <4 RK_PB6 RK_FUNC_GPIO &pcfg_pull_down>,
> + /* PCIE30X4_WAKEn_M1_L */
> + <4 RK_PB5 4 &pcfg_pull_down>;
> + };
> };
>
Thanks
-Anand
