Il 11/07/24 18:33, Nícolas F. R. A. Prado ha scritto:
On Thu, Jul 11, 2024 at 11:21:14AM +0200, AngeloGioacchino Del Regno wrote:
Il 11/07/24 06:13, Macpaul Lin ha scritto:
On 7/11/24 03:15, Nícolas F. R. A. Prado wrote:
On Fri, Jan 19, 2024 at 10:12:07AM +0100, AngeloGioacchino Del Regno wrote:
Il 18/01/24 19:36, Nícolas F. R. A. Prado ha scritto:
Hi,
KernelCI has identified a failure in the probe of one of the USB controllers on
the MT8195-Tomato Chromebook [1]:
[ 16.336840] xhci-mtk 11290000.usb: uwk - reg:0x400, version:104
[ 16.337081] xhci-mtk 11290000.usb: xHCI Host Controller
[ 16.337093] xhci-mtk 11290000.usb: new USB bus
registered, assigned bus number 5
[ 16.357114] xhci-mtk 11290000.usb: clocks are not stable (0x1003d0f)
[ 16.357119] xhci-mtk 11290000.usb: can't setup: -110
[ 16.357128] xhci-mtk 11290000.usb: USB bus 5 deregistered
[ 16.359484] xhci-mtk: probe of 11290000.usb failed with error -110
A previous message [2] suggests that a force-mode phy property that has been
merged might help with addressing the issue, however it's not clear to me how,
given that the controller at 1129000 uses a USB2 phy and the phy driver patch
only looks for the property on USB3 phys.
Worth noting that the issue doesn't always happen. For instance the test did
pass for next-20240110 and then failed again on today's next [3]. But it does
seem that the issue was introduced, or at least became much more likely, between
next-20231221 and next-20240103, given that it never happened out of 10 runs
before, and after that has happened 5 out of 7 times.
Note: On the Tomato Chromebook specifically this USB controller is not connected
to anything.
[1] https://urldefense.com/v3/__https://linux.kernelci.org/test/case/id/659ce3506673076a8c52a428/__;!!CTRNKA9wMg0ARbw!jtg5drII8WUPwTiL4sWZiSRPXN-EBN8ctTGI85sirqvkmaUbA5z-wrLqPPfxlZZkQ7NItOWDT97OSdENT5oGHKY$
[2] https://lore.kernel.org/all/239def9b-437b-9211-7844-af4332651df0@xxxxxxxxxxxx/
[3] https://urldefense.com/v3/__https://linux.kernelci.org/test/case/id/65a8c66ee89acb56ac52a405/__;!!CTRNKA9wMg0ARbw!jtg5drII8WUPwTiL4sWZiSRPXN-EBN8ctTGI85sirqvkmaUbA5z-wrLqPPfxlZZkQ7NItOWDT97OSdENi-d0sVc$
Thanks,
Nícolas
Hey Nícolas,
I wonder if this is happening because of async probe... I have seen those happening
once in a (long) while on MT8186 as well with the same kind of flakiness and I am
not even able to reproduce anymore.
For MT8195 Tomato, I guess we can simply disable that controller without any side
effects but, at the same time, I'm not sure that this would be the right thing to
do in this case.
Besides, the controller at 11290000 is the only one that doesn't live behind MTU3,
but I don't know if that can ring any bell....
An update on this issue: it looks like it only happens if "xhci-mtk
11290000.usb" probes before "mtk-pcie-gen3 112f8000.pcie". What they have in
common is that both of those nodes use phys that share the same t-phy block:
pcie uses the usb3 phy while xhci uses the usb2 phy. So it seems that some of
the initialization done by the pcie controller might be implicitly needed by the
usb controller.
This should help to narrow down the issue and find a proper fix for it.
Thanks,
Nícolas
'force-mode' should only applied to the boards which require XHCI
function instead of a PCIE port.
For example, mt8395-genio-1200-evk.dts requires property 'force-mode' to
fix probe issue for USBC @11290000.
https://git.kernel.org/pub/scm/linux/kernel/git/mediatek/linux.git/commit/?h=v6.10-next/dts64&id=666e6f39faff05fe12bfc64c64aa9015135ce783
'force-mode' should be no need for tomato boards and the behavior should
be the same as before.
Another possibility is the firmware change on tomato boards. I'm not
sure if there is any changes on tomato's recent firmware for tphy of
this port, which could also be a reason causes this kind of failure.
I don't have tomato boards on hand.
Hello Macpaul,
it's just about the usb node missing a power domain: as the PCIE_MAC_P1 domain
seems to be shared between USB and PCIe, adding it to the USB node fixes the
setup phase.
I'll send a devicetree fix soon.
Hi,
As I replied to that patch
(https://lore.kernel.org/all/20240711093230.118534-1-angelogioacchino.delregno@xxxxxxxxxxxxx)
it didn't fix the issue for me, but I have more updates:
I confirmed the pcie was doing some required setup since disabling the pcie1
node made the issue always happen, and that also made it easier to test.
I was able to track the issue down to the following clock:
<&infracfg_ao CLK_INFRA_AO_PCIE_P1_TL_96M>
Adding it to the clocks property of the xhci1 node fixed the issue.
Clocks is what I tried first, and didn't do anything for me...
..anyway, can you at this point try to run that solution on the multiple
devices that we have in the lab through KernelCI?
That would help validating that you're not facing the same false positive
as mine from yesterday...
I'm just not sure from a DT perspective what's the right way to describe this
clock. The node doesn't have the frmcnt_ck, is this that clock? Or is it
another clock that currently isn't described in the dt-bindings and driver?
That's the PCI-Express Root Port (RP) Transaction Layer (TL) clock... and I have
no idea why this has anything to do with USB.
MediaTek, is that a hardware quirk? What is the relation between this clock and
the USB controller at 11290000?
Thanks,
Angelo
Thanks,
Nícolas
