Adds bootph-* properties to the leaf nodes to enable U-boot to
utilise them.
Signed-off-by: Manorit Chawdhry <m-chawdhry@xxxxxx>
---
.../arm64/boot/dts/ti/k3-j721e-common-proc-board.dts | 20 ++++++++++++++++++++
arch/arm64/boot/dts/ti/k3-j721e-main.dtsi | 2 ++
arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi | 10 ++++++++++
arch/arm64/boot/dts/ti/k3-j721e-sk.dts | 18 ++++++++++++++++++
arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi | 5 +++++
5 files changed, 55 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
index 8230d53cd696..ebc9ab3b6790 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
@@ -193,6 +193,7 @@ J721E_IOPAD(0x1c0, PIN_OUTPUT, 1) /* (AA2) SPI0_CS0.UART0_RTSn */
J721E_IOPAD(0x1e8, PIN_INPUT, 0) /* (AB2) UART0_RXD */
J721E_IOPAD(0x1ec, PIN_OUTPUT, 0) /* (AB3) UART0_TXD */
>;
+ bootph-all;
};
main_uart1_pins_default: main-uart1-default-pins {
@@ -234,6 +235,7 @@ J721E_IOPAD(0x240, PIN_INPUT, 0) /* (R26) MMC1_DAT3 */
J721E_IOPAD(0x258, PIN_INPUT, 0) /* (P23) MMC1_SDCD */
J721E_IOPAD(0x25c, PIN_INPUT, 0) /* (R28) MMC1_SDWP */
>;
+ bootph-all;
};
vdd_sd_dv_alt_pins_default: vdd-sd-dv-alt-default-pins {
@@ -247,6 +249,7 @@ main_usbss0_pins_default: main-usbss0-default-pins {
J721E_IOPAD(0x290, PIN_OUTPUT, 0) /* (U6) USB0_DRVVBUS */
J721E_IOPAD(0x210, PIN_INPUT, 7) /* (W3) MCAN1_RX.GPIO1_3 */
>;
+ bootph-all;
};
main_usbss1_pins_default: main-usbss1-default-pins {
@@ -272,6 +275,7 @@ main_i2c0_pins_default: main-i2c0-default-pins {
J721E_IOPAD(0x220, PIN_INPUT_PULLUP, 0) /* (AC5) I2C0_SCL */
J721E_IOPAD(0x224, PIN_INPUT_PULLUP, 0) /* (AA5) I2C0_SDA */
>;
+ bootph-all;
};
main_i2c1_pins_default: main-i2c1-default-pins {
@@ -342,6 +346,7 @@ wkup_uart0_pins_default: wkup-uart0-default-pins {
J721E_WKUP_IOPAD(0xa0, PIN_INPUT, 0) /* (J29) WKUP_UART0_RXD */
J721E_WKUP_IOPAD(0xa4, PIN_OUTPUT, 0) /* (J28) WKUP_UART0_TXD */
>;
+ bootph-all;
};
mcu_uart0_pins_default: mcu-uart0-default-pins {
@@ -351,6 +356,7 @@ J721E_WKUP_IOPAD(0xec, PIN_OUTPUT, 0) /* (J27) WKUP_GPIO0_15.MCU_UART0_RTSn */
J721E_WKUP_IOPAD(0xe4, PIN_INPUT, 0) /* (H28) WKUP_GPIO0_13.MCU_UART0_RXD */
J721E_WKUP_IOPAD(0xe0, PIN_OUTPUT, 0) /* (G29) WKUP_GPIO0_12.MCU_UART0_TXD */
>;
+ bootph-all;
};
sw11_button_pins_default: sw11-button-default-pins {
@@ -370,6 +376,7 @@ J721E_WKUP_IOPAD(0x4c, PIN_INPUT, 0) /* (C23) MCU_OSPI1_D3 */
J721E_WKUP_IOPAD(0x3c, PIN_INPUT, 0) /* (B23) MCU_OSPI1_DQS */
J721E_WKUP_IOPAD(0x38, PIN_INPUT, 0) /* (A23) MCU_OSPI1_LBCLKO */
>;
+ bootph-all;
};
mcu_cpsw_pins_default: mcu-cpsw-default-pins {
@@ -427,6 +434,7 @@ wkup_gpio_pins_default: wkup-gpio-default-pins {
pinctrl-single,pins = <
J721E_WKUP_IOPAD(0xd0, PIN_INPUT, 7) /* (C14) WKUP_GPIO0_8 */
>;
+ bootph-all;
};
};
@@ -435,12 +443,14 @@ &wkup_uart0 {
status = "reserved";
pinctrl-names = "default";
pinctrl-0 = <&wkup_uart0_pins_default>;
+ bootph-all;
};
&mcu_uart0 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&mcu_uart0_pins_default>;
+ bootph-all;
};
&main_uart0 {
@@ -449,6 +459,7 @@ &main_uart0 {
pinctrl-0 = <&main_uart0_pins_default>;
/* Shared with ATF on this platform */
power-domains = <&k3_pds 146 TI_SCI_PD_SHARED>;
+ bootph-all;
};
&main_uart1 {
@@ -473,6 +484,7 @@ &wkup_gpio0 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&wkup_gpio_pins_default>;
+ bootph-all;
};
&main_gpio0 {
@@ -489,6 +501,7 @@ &main_sdhci0 {
non-removable;
ti,driver-strength-ohm = <50>;
disable-wp;
+ bootph-all;
};
&main_sdhci1 {
@@ -500,10 +513,12 @@ &main_sdhci1 {
pinctrl-0 = <&main_mmc1_pins_default>;
ti,driver-strength-ohm = <50>;
disable-wp;
+ bootph-all;
};
&usb_serdes_mux {
idle-states = <1>, <0>; /* USB0 to SERDES3, USB1 to SERDES1 */
+ bootph-all;
};
&serdes_ln_ctrl {
@@ -513,6 +528,7 @@ &serdes_ln_ctrl {
<J721E_SERDES3_LANE0_USB3_0_SWAP>, <J721E_SERDES3_LANE1_USB3_0>,
<J721E_SERDES4_LANE0_EDP_LANE0>, <J721E_SERDES4_LANE1_EDP_LANE1>,
<J721E_SERDES4_LANE2_EDP_LANE2>, <J721E_SERDES4_LANE3_EDP_LANE3>;
+ bootph-all;
};
&serdes_wiz3 {
@@ -534,6 +550,7 @@ &usbss0 {
pinctrl-names = "default";
pinctrl-0 = <&main_usbss0_pins_default>;
ti,vbus-divider;
+ bootph-all;
};
&usb0 {
@@ -541,6 +558,7 @@ &usb0 {
maximum-speed = "super-speed";
phys = <&serdes3_usb_link>;
phy-names = "cdns3,usb3-phy";
+ bootph-all;
};
&usbss1 {
@@ -569,6 +587,7 @@ flash@0 {
cdns,tchsh-ns = <60>;
cdns,tslch-ns = <60>;
cdns,read-delay = <2>;
+ bootph-all;
partitions {
compatible = "fixed-partitions";
@@ -650,6 +669,7 @@ exp2: gpio@22 {
reg = <0x22>;
gpio-controller;
#gpio-cells = <2>;
+ bootph-all;
p09-hog {
/* P11 - MCASP/TRACE_MUX_S0 */
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
index 0da785be80ff..584badcb796d 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
@@ -226,6 +226,7 @@ secure_proxy_main: mailbox@32c00000 {
<0x00 0x32800000 0x00 0x100000>;
interrupt-names = "rx_011";
interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ bootph-all;
};
smmu0: iommu@36600000 {
@@ -2854,5 +2855,6 @@ main_esm: esm@700000 {
compatible = "ti,j721e-esm";
reg = <0x0 0x700000 0x0 0x1000>;
ti,esm-pins = <344>, <345>;
+ bootph-all;
};
};
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
index 6b6ef6a30614..ff9d8a7c405c 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
@@ -17,20 +17,24 @@ dmsc: system-controller@44083000 {
reg-names = "debug_messages";
reg = <0x00 0x44083000 0x0 0x1000>;
+ bootph-all;
k3_pds: power-controller {
compatible = "ti,sci-pm-domain";
#power-domain-cells = <2>;
+ bootph-all;
};
k3_clks: clock-controller {
compatible = "ti,k2g-sci-clk";
#clock-cells = <2>;
+ bootph-all;
};
k3_reset: reset-controller {
compatible = "ti,sci-reset";
#reset-cells = <2>;
+ bootph-all;
};
};
@@ -61,6 +65,7 @@ wkup_conf: bus@43000000 {
chipid: chipid@14 {
compatible = "ti,am654-chipid";
reg = <0x14 0x4>;
+ bootph-all;
};
};
@@ -115,6 +120,7 @@ mcu_timer0: timer@40400000 {
ti,timer-pwm;
/* Non-MPU Firmware usage */
status = "reserved";
+ bootph-pre-ram;
};
mcu_timer1: timer@40410000 {
@@ -475,6 +481,7 @@ mcu_ringacc: ringacc@2b800000 {
ti,sci = <&dmsc>;
ti,sci-dev-id = <235>;
msi-parent = <&main_udmass_inta>;
+ bootph-all;
};
mcu_udmap: dma-controller@285c0000 {
@@ -499,6 +506,7 @@ mcu_udmap: dma-controller@285c0000 {
ti,sci-rm-range-rchan = <0x0a>, /* RX_CHAN */
<0x0b>; /* RX_HCHAN */
ti,sci-rm-range-rflow = <0x00>; /* GP RFLOW */
+ bootph-all;
};
};
@@ -515,6 +523,7 @@ secure_proxy_mcu: mailbox@2a480000 {
* firmware on non-MPU processors
*/
status = "disabled";
+ bootph-pre-ram;
};
mcu_cpsw: ethernet@46000000 {
@@ -687,6 +696,7 @@ wkup_vtm0: temperature-sensor@42040000 {
<0x00 0x43000300 0x00 0x10>;
power-domains = <&k3_pds 154 TI_SCI_PD_EXCLUSIVE>;
#thermal-sensor-cells = <1>;
+ bootph-pre-ram;
};
mcu_esm: esm@40800000 {
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-sk.dts b/arch/arm64/boot/dts/ti/k3-j721e-sk.dts
index 89fbfb21e5d3..b63d48719090 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721e-sk.dts
@@ -346,6 +346,7 @@ J721E_IOPAD(0x244, PIN_INPUT, 0) /* (R25) MMC1_DAT2 */
J721E_IOPAD(0x240, PIN_INPUT, 0) /* (R26) MMC1_DAT3 */
J721E_IOPAD(0x258, PIN_INPUT, 0) /* (P23) MMC1_SDCD */
>;
+ bootph-all;
};
main_uart0_pins_default: main-uart0-default-pins {
@@ -355,6 +356,7 @@ J721E_IOPAD(0x1f4, PIN_OUTPUT, 0) /* (AB1) UART0_RTSn */
J721E_IOPAD(0x1e8, PIN_INPUT, 0) /* (AB2) UART0_RXD */
J721E_IOPAD(0x1ec, PIN_OUTPUT, 0) /* (AB3) UART0_TXD */
>;
+ bootph-all;
};
main_uart1_pins_default: main-uart1-default-pins {
@@ -390,12 +392,14 @@ main_usbss0_pins_default: main-usbss0-default-pins {
J721E_IOPAD(0x290, PIN_OUTPUT, 0) /* (U6) USB0_DRVVBUS */
J721E_IOPAD(0x210, PIN_INPUT, 7) /* (W3) MCAN1_RX.GPIO1_3 */
>;
+ bootph-all;
};
main_usbss1_pins_default: main-usbss1-default-pins {
pinctrl-single,pins = <
J721E_IOPAD(0x214, PIN_OUTPUT, 4) /* (V4) MCAN1_TX.USB1_DRVVBUS */
>;
+ bootph-all;
};
main_csi_mux_sel_pins_default: main-csi-mux-sel-default-pins {
@@ -594,6 +598,7 @@ J721E_WKUP_IOPAD(0x24, PIN_INPUT, 0) /* (B22) MCU_OSPI0_D6 */
J721E_WKUP_IOPAD(0x28, PIN_INPUT, 0) /* (G21) MCU_OSPI0_D7 */
J721E_WKUP_IOPAD(0x8, PIN_INPUT, 0) /* (D21) MCU_OSPI0_DQS */
>;
+ bootph-all;
};
vdd_mmc1_en_pins_default: vdd-mmc1-en-default-pins {
@@ -622,6 +627,7 @@ J721E_WKUP_IOPAD(0xf4, PIN_OUTPUT, 2)/* (D25) MCU_I3C0_SDA.MCU_UART0_RTSn */
J721E_WKUP_IOPAD(0xe4, PIN_INPUT, 0) /* (H28) WKUP_GPIO0_13.MCU_UART0_RXD */
J721E_WKUP_IOPAD(0xe0, PIN_OUTPUT, 0)/* (G29) WKUP_GPIO0_12.MCU_UART0_TXD */
>;
+ bootph-pre-ram;
};
wkup_i2c0_pins_default: wkup-i2c0-default-pins {
@@ -629,6 +635,7 @@ wkup_i2c0_pins_default: wkup-i2c0-default-pins {
J721E_WKUP_IOPAD(0xf8, PIN_INPUT_PULLUP, 0) /* (J25) WKUP_I2C0_SCL */
J721E_WKUP_IOPAD(0xfc, PIN_INPUT_PULLUP, 0) /* (H24) WKUP_I2C0_SDA */
>;
+ bootph-all;
};
mcu_mcan0_pins_default: mcu-mcan0-default-pins {
@@ -657,6 +664,7 @@ &wkup_uart0 {
status = "reserved";
pinctrl-names = "default";
pinctrl-0 = <&wkup_uart0_pins_default>;
+ bootph-all;
};
&wkup_i2c0 {
@@ -821,6 +829,7 @@ &mcu_uart0 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&mcu_uart0_pins_default>;
+ bootph-all;
};
&main_uart0 {
@@ -829,6 +838,7 @@ &main_uart0 {
pinctrl-0 = <&main_uart0_pins_default>;
/* Shared with ATF on this platform */
power-domains = <&k3_pds 146 TI_SCI_PD_SHARED>;
+ bootph-all;
};
&main_uart1 {
@@ -846,6 +856,7 @@ &main_sdhci1 {
pinctrl-0 = <&main_mmc1_pins_default>;
ti,driver-strength-ohm = <50>;
disable-wp;
+ bootph-all;
};
&ospi0 {
@@ -864,6 +875,7 @@ flash@0 {
cdns,tchsh-ns = <60>;
cdns,tslch-ns = <60>;
cdns,read-delay = <4>;
+ bootph-all;
partitions {
compatible = "fixed-partitions";
@@ -1003,6 +1015,7 @@ &wkup_gpio0 {
&usb_serdes_mux {
idle-states = <1>, <1>; /* USB0 to SERDES3, USB1 to SERDES2 */
+ bootph-all;
};
&serdes_ln_ctrl {
@@ -1012,6 +1025,7 @@ &serdes_ln_ctrl {
<J721E_SERDES3_LANE0_USB3_0_SWAP>, <J721E_SERDES3_LANE1_USB3_0>,
<J721E_SERDES4_LANE0_EDP_LANE0>, <J721E_SERDES4_LANE1_EDP_LANE1>,
<J721E_SERDES4_LANE2_EDP_LANE2>, <J721E_SERDES4_LANE3_EDP_LANE3>;
+ bootph-all;
};
&serdes_wiz3 {
@@ -1051,6 +1065,7 @@ &usbss0 {
pinctrl-names = "default";
pinctrl-0 = <&main_usbss0_pins_default>;
ti,vbus-divider;
+ bootph-all;
};
&usb0 {
@@ -1058,6 +1073,7 @@ &usb0 {
maximum-speed = "super-speed";
phys = <&serdes3_usb_link>;
phy-names = "cdns3,usb3-phy";
+ bootph-all;
};
&serdes2 {
@@ -1074,6 +1090,7 @@ &usbss1 {
pinctrl-names = "default";
pinctrl-0 = <&main_usbss1_pins_default>;
ti,vbus-divider;
+ bootph-all;
};
&usb1 {
@@ -1081,6 +1098,7 @@ &usb1 {
maximum-speed = "super-speed";
phys = <&serdes2_usb_link>;
phy-names = "cdns3,usb3-phy";
+ bootph-all;
};
&mcu_cpsw {
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
index 5ba947771b84..86bfc5e21eed 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
@@ -151,6 +151,7 @@ wkup_i2c0_pins_default: wkup-i2c0-default-pins {
J721E_WKUP_IOPAD(0xf8, PIN_INPUT_PULLUP, 0) /* (J25) WKUP_I2C0_SCL */
J721E_WKUP_IOPAD(0xfc, PIN_INPUT_PULLUP, 0) /* (H24) WKUP_I2C0_SDA */
>;
+ bootph-all;
};
pmic_irq_pins_default: pmic-irq-default-pins {
@@ -173,6 +174,7 @@ J721E_WKUP_IOPAD(0x0024, PIN_INPUT, 0) /* MCU_OSPI0_D6 */
J721E_WKUP_IOPAD(0x0028, PIN_INPUT, 0) /* MCU_OSPI0_D7 */
J721E_WKUP_IOPAD(0x002c, PIN_OUTPUT, 0) /* MCU_OSPI0_CSn0 */
>;
+ bootph-all;
};
mcu_fss0_hpb0_pins_default: mcu-fss0-hpb0-default-pins {
@@ -192,6 +194,7 @@ J721E_WKUP_IOPAD(0x20, PIN_INPUT, 1) /* MCU_HYPERBUS0_DQ5 */
J721E_WKUP_IOPAD(0x24, PIN_INPUT, 1) /* MCU_HYPERBUS0_DQ6 */
J721E_WKUP_IOPAD(0x28, PIN_INPUT, 1) /* MCU_HYPERBUS0_DQ7 */
>;
+ bootph-all;
};
};
@@ -378,6 +381,7 @@ flash@0 {
cdns,tchsh-ns = <60>;
cdns,tslch-ns = <60>;
cdns,read-delay = <0>;
+ bootph-all;
partitions {
compatible = "fixed-partitions";
@@ -440,6 +444,7 @@ &hbmc {
flash@0,0 {
compatible = "cypress,hyperflash", "cfi-flash";
reg = <0x00 0x00 0x4000000>;
+ bootph-all;
partitions {
compatible = "fixed-partitions";
--
2.45.1
