On 2024-07-02 16:25, Philipp Puschmann wrote:
On 2024-07-02 14:46, Philipp Puschmann wrote:
Providing ethernet aliases solves a subtle problem for the rk3568.
The
bus_id used for the sysfs directory name of the mdio. Without
ethernet
alias the bus_id is always 0 and so creating the sysfs directory for
the
second mdio fails with a duplicate filename error and by this the
setup
of the second ethernet port fails too.
Note: The alias numbering is inverted as gmac1 comes from more
generic
rk356x.dtsi but gmac0 comes from specialised rk3568.
Please see the following commits and the discussions on the
rockchip-linux
mailing list that are linked in them:
- b0140a1b3b1d ("arm64: dts: rockchip: Add ethernet0 alias to the dts
for RK3588(S) boards")
- 36d9b3ae708e ("arm64: dts: rockchip: Add ethernet0 alias to the dts
for RK3566 boards")
- 5d90cb1edcf7 ("arm64: dts: rockchip: Remove ethernet0 alias from the
SoC dtsi for RK3399")
- c900fef5deff ("arm64: dts: rockchip: Remove ethernet0 alias from the
SoC dtsi for RK3368")
To sum it up, ethernetX aliases are considered board-level features,
because not all boards/devices actually expose the Ethernet interfaces
built into the SoCs. Thus, adding ethernetX aliases to the SoC dtsi
files, unfortunately, isn't an acceptable option.
Are ethernet aliases are handled differently than i2c, serial and spi
aliases?
There are aliases for each of them, without doing any harm. And even if
the gmac
nodes are disabled with status property?
In a word, yes; they are handled a bit differently, which I already
tried
to sum up. As Krzysztof already noted, please read the discussions
linked
in the patches listed above.
On my rk3568-based custom board i had no ethernet aliases and
networking was
enabled normally with the status properties of the gmac nodes. Either
one or
the other or both network devices were initialized. Would be strange if
an
alias would be used without regard to initializing a device driver.
It's also about following the TRMs and the aliases (or common names)
defined
in them, as described in the above-mentioned discussions.
The sysfs issue that you've discovered should be instead solved in
some
other, more systemic way.
The bus_id value comes from stmmac_platform.c and of_alias_get_id()
with
"ethernet" as parameter is used, what is a common way in the kernel. It
delivers unique ints starting with 0. stmmac_mdio then uses the bus_id
to
create a mdio bus id string stmmac-${bus_id} to register a mdio_bus.
From my understanding this kind of bus id is commonly used to name
devices
and paths in the sysfs. Viewed only this problem it would be possible
to use other information like the node address or some unique
information to use it as unique part of the mdio bus id. But doesn't
break
things too, at least some kind of convention?
Another hack i tried first, was to use a static increasing int to get
the bus_id. This would keep the resulting sysfs tree probably unchanged
but would drop the connection between dts and bus numbering in sysfs.
Wouldn't those issues be solved by simply defining the needed ethernetX
aliases in the dts file for your board?
Signed-off-by: Philipp Puschmann <p.puschmann@xxxxxxxxxxx>
---
arch/arm64/boot/dts/rockchip/rk3568.dtsi | 4 ++++
arch/arm64/boot/dts/rockchip/rk356x.dtsi | 1 +
2 files changed, 5 insertions(+)
diff --git a/arch/arm64/boot/dts/rockchip/rk3568.dtsi
b/arch/arm64/boot/dts/rockchip/rk3568.dtsi
index f1be76a54ceb..42018c8666e0 100644
--- a/arch/arm64/boot/dts/rockchip/rk3568.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3568.dtsi
@@ -8,6 +8,10 @@
/ {
compatible = "rockchip,rk3568";
+ aliases {
+ ethernet1 = &gmac0;
+ };
+
sata0: sata@fc000000 {
compatible = "rockchip,rk3568-dwc-ahci", "snps,dwc-ahci";
reg = <0 0xfc000000 0 0x1000>;
diff --git a/arch/arm64/boot/dts/rockchip/rk356x.dtsi
b/arch/arm64/boot/dts/rockchip/rk356x.dtsi
index d8543b5557ee..e13bd7b24752 100644
--- a/arch/arm64/boot/dts/rockchip/rk356x.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk356x.dtsi
@@ -43,6 +43,7 @@ aliases {
spi1 = &spi1;
spi2 = &spi2;
spi3 = &spi3;
+ ethernet0 = &gmac1;
};
cpus {
