Re: [PATCH v2 04/10] dt-bindings: iio: adc: adi,ad7606: improve descriptions

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Fri, 28 Jun 2024 14:48:22 +0000
Guillaume Stols <gstols@xxxxxxxxxxxx> wrote:

> Reword a few descriptions, and normalize the text width to 80 characters.
> 
> Signed-off-by: Guillaume Stols <gstols@xxxxxxxxxxxx>

One minor comment inline.  I can tidy it up whilst applying if
everything else is fine in the rest of the series.

Jonathan

> ---
>  .../devicetree/bindings/iio/adc/adi,ad7606.yaml    | 33 +++++++++++++---------
>  1 file changed, 20 insertions(+), 13 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml
> index 32caa9fc00e4..509970922cda 100644
> --- a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml
> +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml
> @@ -36,6 +36,9 @@ properties:
>    avcc-supply: true
>  
>    interrupts:
> +    description:
> +      The BUSY pin falling edge indicates that the conversion is over, and thus
> +      new data is available.
>      maxItems: 1
>  
>    adi,conversion-start-gpios:
> @@ -48,8 +51,9 @@ properties:
>    reset-gpios:
>      description:
>        Must be the device tree identifier of the RESET pin. If specified, it will
> -      be asserted during driver probe. As the line is active high, it should be
> -      marked GPIO_ACTIVE_HIGH.
> +      be asserted during driver probe. On the AD7606x, as the line is active
> +      high, it should be marked GPIO_ACTIVE_HIGH. On the AD7616, as the line is
> +      active low, it should be marked GPIO_ACTIVE_LOW.
>      maxItems: 1
>  
>    standby-gpios:
> @@ -62,36 +66,39 @@ properties:
>  
>    adi,first-data-gpios:
>      description:
> -      Must be the device tree identifier of the FRSTDATA pin.  The FRSTDATA
> +      Must be the device tree identifier of the FRSTDATA pin. The FRSTDATA
>        output indicates when the first channel, V1, is being read back on either
> -      the parallel, byte or serial interface.  As the line is active high, it
> +      the parallel, byte or serial interface. As the line is active high, it
>        should be marked GPIO_ACTIVE_HIGH.
>      maxItems: 1
>  
>    adi,range-gpios:
>      description:
> -      Must be the device tree identifier of the RANGE pin. The polarity on this
> +      Must be the device tree identifier of the RANGE pin. The state on this
>        pin determines the input range of the analog input channels. If this pin
>        is tied to a logic high, the analog input range is ±10V for all channels.
> -      If this pin is tied to a logic low, the analog input range is ±5V for all
> -      channels. As the line is active high, it should be marked
> +      On the AD760X, if this pin is tied to a logic low, the analog input range
> +      is ±5V for all channels. As the line is active high, it should be marked
>        GPIO_ACTIVE_HIGH.
>      maxItems: 1
>  
>    adi,oversampling-ratio-gpios:
>      description:
>        Must be the device tree identifier of the over-sampling mode pins. As the
> -      line is active high, it should be marked GPIO_ACTIVE_HIGH.
> +      line is active high, it should be marked GPIO_ACTIVE_HIGH. On the AD7606X
> +      parts that support it, if all 3 pins are tied to a logic high, software
> +      mode is enabled.
>      maxItems: 3
>  
>    adi,sw-mode:
>      description:
> -      Software mode of operation, so far available only for ad7616 and ad7606b.
> +      Software mode of operation, so far available only for AD7616 and AD7606b.
>        It is enabled when all three oversampling mode pins are connected to high
> -      level. The device is configured by the corresponding registers. If the
> -      adi,oversampling-ratio-gpios property is defined, then the driver will set
> -      the oversampling gpios to high. Otherwise, it is assumed that the pins are
> -      hardwired to VDD.
> +      level for the AD7606B, or all two range selection pins are connected to
If rolling again for some reason 

       level for the AD7606B, or both the range selections are connected to high
       level for the AD7616.

> +      high level for the AD7616. The device is configured by the corresponding
> +      registers. If the adi,oversampling-ratio-gpios property is defined, then
> +      the driver will set the oversampling gpios to high. Otherwise, it is
> +      assumed that the pins are hardwired to VDD.
>      type: boolean
>  
>  required:
> 






[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux