[PATCH 4/5] arm64: dts: rockchip: use generic Ethernet PHY reset bindings for Lunzn Fastrhino R68S

[Chukun Pan <amadeus@xxxxxxxxxx>]

Replace the deprecated snps,reset-xxx bindings to the generic Ethernet PHY
reset GPIO bindings. Also fixed the PHY address and reset GPIOs (does not
match the corresponding pinctrl). Since we use rgmii-id as the phy mode,
remove the useless tx_delay and rx_delay.

Fixes: b9f8ca655d80 ("arm64: dts: rockchip: Add Lunzn Fastrhino R68S")
Signed-off-by: Chukun Pan <amadeus@xxxxxxxxxx>
---
 .../dts/rockchip/rk3568-fastrhino-r68s.dts    | 26 +++++++------------
 1 file changed, 10 insertions(+), 16 deletions(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk3568-fastrhino-r68s.dts b/arch/arm64/boot/dts/rockchip/rk3568-fastrhino-r68s.dts
index a3339186e89c..d27eb37b5b35 100644
--- a/arch/arm64/boot/dts/rockchip/rk3568-fastrhino-r68s.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3568-fastrhino-r68s.dts
@@ -39,12 +39,6 @@ &gmac0_tx_bus2
 		     &gmac0_rx_bus2
 		     &gmac0_rgmii_clk
 		     &gmac0_rgmii_bus>;
-	snps,reset-gpio = <&gpio0 RK_PB0 GPIO_ACTIVE_LOW>;
-	snps,reset-active-low;
-	/* Reset time is 15ms, 50ms for rtl8211f */
-	snps,reset-delays-us = <0 15000 50000>;
-	tx_delay = <0x3c>;
-	rx_delay = <0x2f>;
 	status = "okay";
 };
 
@@ -61,30 +55,30 @@ &gmac1m1_tx_bus2
 		     &gmac1m1_rx_bus2
 		     &gmac1m1_rgmii_clk
 		     &gmac1m1_rgmii_bus>;
-	snps,reset-gpio = <&gpio0 RK_PB1 GPIO_ACTIVE_LOW>;
-	snps,reset-active-low;
-	/* Reset time is 15ms, 50ms for rtl8211f */
-	snps,reset-delays-us = <0 15000 50000>;
-	tx_delay = <0x4f>;
-	rx_delay = <0x26>;
 	status = "okay";
 };
 
 &mdio0 {
-	rgmii_phy0: ethernet-phy@0 {
+	rgmii_phy0: ethernet-phy@1 {
 		compatible = "ethernet-phy-ieee802.3-c22";
-		reg = <0>;
+		reg = <0x1>;
 		pinctrl-0 = <&eth_phy0_reset_pin>;
 		pinctrl-names = "default";
+		reset-assert-us = <20000>;
+		reset-deassert-us = <100000>;
+		reset-gpios = <&gpio1 RK_PB0 GPIO_ACTIVE_LOW>;
 	};
 };
 
 &mdio1 {
-	rgmii_phy1: ethernet-phy@0 {
+	rgmii_phy1: ethernet-phy@1 {
 		compatible = "ethernet-phy-ieee802.3-c22";
-		reg = <0>;
+		reg = <0x1>;
 		pinctrl-0 = <&eth_phy1_reset_pin>;
 		pinctrl-names = "default";
+		reset-assert-us = <20000>;
+		reset-deassert-us = <100000>;
+		reset-gpios = <&gpio1 RK_PB1 GPIO_ACTIVE_LOW>;
 	};
 };
 
-- 
2.25.1