On Wed, Jun 26, 2024 at 06:07:50PM GMT, Krishna chaitanya chundru wrote:
> QPS615 switch power is controlled by GPIO's. Once the GPIO's are
> enabled, switch power will be on.
>
> Make all GPIO's as fixed regulators and inter link them so that
> enabling the regulator will enable power to the switch by enabling
> GPIO's.
>
> Enable i2c0 which is required to configure the switch.
>
> Signed-off-by: Krishna chaitanya chundru <quic_krichai@xxxxxxxxxxx>
> ---
> arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts | 55 ++++++++++++++++++++++++++++
> 1 file changed, 55 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
> index a085ff5b5fb2..5b453896a6c9 100644
> --- a/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
> +++ b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
> @@ -511,6 +511,61 @@ vreg_bob_3p296: bob {
> regulator-max-microvolt = <3960000>;
> };
> };
> +
> + qps615_0p9_vreg: qps615-0p9-vreg {
Keep nodes sorted by address, node name, then label.
Perhaps name the nodes "regulator-<name>" to group static regulators
together.
> + compatible = "regulator-fixed";
> + regulator-name = "qps615_0p9_vreg";
Is this the name used for the output of the regulator in the schematics?
> + gpio = <&pm8350c_gpios 2 0>;
Replace that 0 with GPIO_ACTIVE_HIGH.
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + enable-active-high;
> + regulator-enable-ramp-delay = <4300>;
> + };
> +
> + qps615_1p8_vreg: qps615-1p8-vreg {
> + compatible = "regulator-fixed";
> + regulator-name = "qps615_1p8_vreg";
> + gpio = <&pm8350c_gpios 3 0>;
> + vin-supply = <&qps615_0p9_vreg>;
This makes me curious, &qps615_0p9_vreg provides 1V, which we feed into
another regulator (which typically would be an LDO) to provide 1.8V...
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + enable-active-high;
> + regulator-enable-ramp-delay = <10000>;
> + };
> +
> + qps615_rsex_vreg: qps615-rsex-vreg {
> + compatible = "regulator-fixed";
> + regulator-name = "qps615_rsex_vreg";
> + gpio = <&pm8350c_gpios 1 0>;
> + vin-supply = <&qps615_1p8_vreg>;
...which is then fed to another LDO(?) which provides 1.8V.
Please double check the schematics and make sure this represents what's
on the board. Feel free to ping me offline and I can help review the
schematics.
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + enable-active-high;
> + regulator-enable-ramp-delay = <10000>;
> + };
> +};
> +
> +&i2c0 {
> + clock-frequency = <100000>;
> + status = "okay";
> +};
> +
> +&pcie1 {
> + pcie@0 {
> + device_type = "pci";
> + reg = <0x0 0x0 0x0 0x0 0x0>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> +
> + bus-range = <0x01 0xff>;
> +
> + qps615@0 {
> + compatible = "pci1179,0623";
> + reg = <0x1000 0x0 0x0 0x0 0x0>;
> + vdda-supply = <&qps615_rsex_vreg>;
I presume you didn't "make qcom/qcs6490-rb3gen2.dtb CHECK_DTBS=1" this,
as "vdda-supply" is not listed as a valid supply in the binding (also
the driver is looking for vdd-supply...)
Regards,
Bjorn
> + switch-i2c-cntrl = <&i2c0>;
> + };
> + };
> };
>
> &gcc {
>
> --
> 2.42.0
>
